Manual

ManualsBrandsOptex ManualsElectronicsWireless Photobeam with Inovonics Transmitter

-1-

Warning

Caution

Warning

Caution

N219

INSTALLATION INSTRUCTIONS

No.59-1552-0 090128

BATTERY OPERATED

PHOTOELECTRIC DETECTOR

AX-100TFR/AX-200 TFR

BATTERY OPERATED

PHOTOELECTRIC DETECTOR

AX-100TFR/AX-200 TFR

•AX-100TFR : Detection range: 30 m (100 ft.)

•AX-200TFR : Detection range: 60 m (200 ft.)

CONTENTS

• Battery-operated detector

Batteries are not included.

Use four LSH20 (3.6 V, 13 Ah) batteries manufactured by SAFT.

Battery life: Approximately five years (AX-100TFR)

Approximately three years (AX-200TFR)

• Back box for wireless transmitters

Back box can conceal two wireless transmitters and batteries.

• N.C./N.O. selection switch

Both N.C. and N.O. input wireless transmitters can be used.

• Battery saving function for wireless transmitter

Turning ON the battery saving timer switch reduces the battery

consumption of the wireless transmitter.

• Intermittent output function

Turning ON the intermittent output function forces intermittent

output while the problem status exists.

• 4 channel beam frequency selector

Crosstalk is eliminated with 4, channel selectable, beam

frequencies. Used when stacking beams or for long range

applications.

• International protection

IP55

• LED indicator for an easy alignment

It flickers on/off to help with easy alignment located on the

receiver.

• D.Q. circuit (environmental disqualification)

The environmental compensation circuit is designed to eliminate

false alarms caused by snow, fog, heavy rain, ice and

misalignment.

• Tamper

Form C opens when either cover or back box or chassis is

removed.

• Beam interruption adjustment function

This function allows you to select the suitable beam interruption

time for any environment.

FEATURES

Failure to follow the instructions provided with

this indication and improper handling may cause

death or serious injury.

Failure to follow the instructions provided with

this indication and improper handling may cause

injury and / or property damage.

Do not use the product for purposes other than the detection

of moving objects such as people and vehicles.

Do not use the product to activate a shutter, etc., which may

cause an accident.

Do not touch the unit base or power terminals of the

product with a wet hand (do not touch when the product

is wet with rain, etc.). It may cause electric shock.

Never attempt to disassemble or repair the product. It may

cause fire or damage to the devices.

Do not use batteries other than those specified.

Specified batteries:

Four LSH20 batteries manufactured by SAFT

Do not use batteries that have different levels of power

remaining (i.e., new and used batteries).

Not observing the above may result in an explosion, leakage

of electrolyte, emission of toxic gases or other outcomes that

may be harmful to people and property.

[Handling of Batteries]

Fire, explosion and severe burn hazard. Do not recharge,

short circuit, crush, disassemble, heat above 100°C (212°F),

incinerate, or expose contents to water.

Do not solder directly to the cell.

Do not pour water over the product with a bucket, hose, etc.

The water may enter, which may cause damage to the

devices.

Clean and check the product periodically for safe use. If any

problem is found, do not attempt to use the product as it is

and have the product repaired by a professional engineer or

electrician.

• Read this instruction manual carefully prior to installation.

• After reading, store this manual carefully in an easily accessible

place for reference.

• This manual uses the following warning indications for correct use

of the product, harm to you or other people and damage to your

assets, which are described below. Be sure to understand the

description before reading the rest of this manual.

This symbol indicates prohibition. The specific prohibited

action is provided in and/or around the figure.

This symbol requires an action or gives an instruction.

INTRODUCTION

1-1 BEFORE YOUR OPERATION 1

1-2 PRECAUTIONS 2

1-3 PARTS IDENTIFICATION 2

PREPARATIONS

2-1 ORDERING DETECTOR BATTERIES 2

2-2

CHECKING THE WIRELESS TRANSMITTER SIZE

INSTALLATION

3-1 WALL MOUNTING 3

3-2 POLE MOUNTING 4

3-3 MOUNTING IN THE BEAM TOWER 5

3-4 WIRING 7

SETTING

4-1 FUNCTION 8

4-2

4 CHANNEL BEAM FREQUENCY SELECTOR

4-3 OPTICAL ALIGNMENT 9

4-4 BEAM INTERRUPTION ADJUSTMENT 9

4-5 ADJUSTING OUTPUT 10

OPERATION CHECK

5-1 LED INDICATION 11

5-2 OPERATION CHECK 11

5-3 TROUBLE SHOOTING 11

SPECIFICATIONS

6-1 SPECIFICATIONS 12

6-2 DIMENSIONS & OPTION 12

INTRODUCTION

1-1

BEFORE YOUR OPERATION

Summary of content (12 pages)

PAGE 1
No.59-1552-0 090128 1 INSTALLATION INSTRUCTIONS 1-1 BEFORE YOUR OPERATION • Read this instruction manual carefully prior to installation. • After reading, store this manual carefully in an easily accessible place for reference. • This manual uses the following warning indications for correct use of the product, harm to you or other people and damage to your assets, which are described below. Be sure to understand the description before reading the rest of this manual.
PAGE 2
Removing the Back Box >> 1-2 PRECAUTIONS 3 Install the unit on a stable surface. Pull Install the pole in a location where sufficient stability can be ensured. 1 Loosen the back box lock screw. 2 Press Do not install the unit in a location where trees, leaves, or other objects that may swing in the wind may block the beam. Removing the Cover >> Do not install the receiver in a location where it is exposed to direct sunlight.
PAGE 3
4 INSTALLATION Insert the specified batteries into the back box. 3-1 WALL MOUNTING 1 Remove the chassis from the back box. Specified batteries SAFT LSH20 3.6V 13Ah Warning 2 • Do not use batteries other than those specified. Specified batteries: Four LSH20 batteries manufactured by SAFT • Do not mix batteries that have different levels of power remaining (i.e., new and used batteries).
PAGE 4
3-2 POLE MOUNTING -Single set 1 Remove the chassis from the back box. 2 Using a screwdriver or similar tool, break the knockout portion as shown. 5 Take steps 3 through 6 refer to sec. “3-1” to install the wireless transmitters and batteries in the back box, and then install the back box on the chassis. Knockout two locations pairing in a horizontal line. 3 Install three pole mounting brackets on the chassis. Tighten the back box lock screw.
PAGE 5
4 Fix the chassis on the pole. 3-3 MOUNTING IN THE BEAM TOWER Detector 1 Detector 2 M4×30 screw (supplied) Mounting inside optional beam tower. M4×30 screw (supplied) 1 Remove the cover from the detector. 2 Loosen the main unit fixing screw and remove the main unit from the back box. U-bracket (supplied) Loosen the main unit fixing screw. Caution Cables are connected between the back box and the main unit. Do not exert an excessive amount of force on the cables. Handle the main unit with care.
PAGE 6
Fix the chassis and main unit mounting bracket (optional) in the tower. 8 After completing the settings and operation check, insert the tamper bushing into each transmitter/receiver. 250 mm (9.8 inch) or less Tamper bushing (option: MP-4) Caution • The switch selection is not recognized with the tamper bushing inserted. Remove the tamper bushing before selecting a function using the switch. • After completing the settings, be sure to insert the tamper bushing to check that all LEDs are OFF.
PAGE 7
3-4 WIRING -Using the N.C. type transmitter -Using the N.O. type transmitter This product is provided with wiring based on the assumption that N.C. wireless transmitters are used. Connect the cables from the back box (Yellow/Yellow-white, Green/Green-white, and Black/Black-white) to the respective terminals on the wireless transmitters. When N.O. wireless transmitters are used, change the wiring and switch settings from initial setting.
PAGE 8
4 b) Long distance protection SETTING Transmitter A 4-1 FUNCTION Receiver A Receiver B 1 1 1 Transmitter B Transmitter C 3 1 Receiver C 3 (All of the following switch settings are factory default.) Since Receiver C may receive the infrared beam from Transmitter A, select their frequencies as shown in the figure above. Monitor jack (Receiver only) Receiver: 1,2: Beam interruption adjustment switch 3: Battery saving timer switch 4: Intermittent output function switch 5: N.C./N.O.
PAGE 9
4-3 OPTICAL ALIGNMENT Horizontal alignment angle 3 Adjust the horizontal and vertical angles while checking the light receiving status by Alarm indicator LED on the pairing receiver. Vertical alignment angle Low battery LED Alarm indicator LED 5° 5° 90° Light interrupted 90° Alarm indicator LED Adjustment level Optical alignment is an important adjustment to increase reliability.
PAGE 10
-Setting the D.Q. output (environmental disqualification) 4-5 ADJUSTING OUTPUT D.Q. will send a trouble signal when the beam strength is below acceptable levels, for more than 20 seconds, due to rain, snow, or heavy fog. -Setting the battery saving timer Alarm output activation are limited by a timer 2 minutes. Even if there are continuous alarm events, the alarm output operates only once in the timer period. OFF Receiver Transmitter Operating Time Chart ON 2 sec. 20 sec.
PAGE 11
5 5-3 TROUBLE SHOOTING OPERATION CHECK If the alarm indicator LED is OFF or flickering even though the beam is being interrupted, do the following: 5-1 LED INDICATION Receiver Transmitter Alarm indicator LED Low battery LED Low battery LED LED Indications Power ON Detection (beam interruption) Low battery power The power LED turns ON. The alarm LED turns ON. The low battery LED flickers. 5-2 OPERATION CHECK After installation is complete, be sure to check the operation.
PAGE 12
6-2 DIMENSIONS & OPTION SPECIFICATIONS -Dimensions 6-1 SPECIFICATIONS AX-100TFR AX-200TFR 30m (100ft.) 60m (200ft.) Maximum arrival distance 265m (870ft.) 530m (1,740ft.) Detection method Infrared beam interruption detection Power Source Current draw * Battery life Variable between 50, 100, 250, 500msec (4 steps) 3.6V 13.0Ah : LSH20 lithium batteries manufactured by SAFT Transmitter : 2 units Receiver : 2 units 620µA 810µA T:300µA + R:320µA T:490µA + R:320µA (at 25°C,3.6VDC) (at 25°C,3.