Users Guide & Installation Manual USHR-0819L
- Content 1. General Information 2. System Components 3. Installation 4. Trouble Shooting 5. Specification 6. Certificates 7. Memo This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions; This device complies with the Industry Canada license-exempt RSS standard(s). Operation is subject to the following conditions; (1) This device may not cause harmful interference.
1. General Information 1.1. Precautions Reference : Direction/Information for the proper operation Cautions : Information for users to avoid malfunctions Warning : Instruction for users to avoid unexpected hazard 1.1.1 Do not drop the device - It may damage the product and its function 1.1.2 Do not place near magnetic material - It may cause of possible malfunction 1.1.3 Product is recommended to be used with original AC/DC adapter 1.1.
1.2 . Features 1.2.1. Summary This device may be installed on residential area, office, warehouse etc. . Following is advantage of using in-building repeater system. I. II. III. IV. V. Decrease dropped call rate Increase signal strength Improve Data / Voice quality Prolong hand phone battery life Improve data Communication Rate This is RF type amplifier for Cellular800MHz and PCS1900MHz signal enhancement. It covers GSM, EDGE, CDMA, WCDMA mobile phone users.
2.
3. Installation 3.1. Installation diagram USHR-0819L 3.1.1. Install Donor Antenna on higher location to avoid any signal interference. 3.1.2. Install service antenna at appropriate location such as wall or roof ceiling. Make sure service antenna is not blocked by furniture or hope appliance. 3.1.3. Use enclosed bolt to fix repeater on the wall and plug in power adaptor. 3.2.
3.3. Repeater and Antenna connection 3.3.1. Connect donor antenna to RVS connector as shown below. 3.3.2. Connect Service antenna to FWD connector as shown below. 3.3.3. Plug in power adaptor to power outlet.
3.3.4. Plug in AD/CD adaptor to connector listed as DC5.6V 3.3.5. Once power is on, it will show 3 green LED light on the front of product as shown below.
4. Trouble Shooting 4.1. LED Status Item GREEN LED RED LED Problem Reference ON - See 4.1.1 OFF OFF See 4.1.2 ON - See 4.1.3 - ON See 4.1.4 OFF OFF See 4.1.5 ON - See 4.1.6 - ON See 4.1.7 OFF OFF See 4.1.8 PWR Cellular PCS 4.1.1. 4.1.2. 4.1.3. 4.1.4. 4.1.5. 4.1.6. 4.1.7. 4.1.8.
5. Specification 5.1. Amplifier Specification Item Operating Frequency Specifications Note Down Link 1930 ~ 1990 MHz Up Link 1850 ~ 1910 MHz PCS1900 BW: 60MHz Down Link 869 ~ 894 MHz Up Link Modulation Type Input Power Output Power Gain Cellular800 BW: 25 MHz 824 ~ 849 MHz GSM, EDGE, CDMA, WCDMA -28dBm max Down Link +12dBm Up Link +15dBm Down Link +12dBm Up Link +15dBm Down Link 65dB (±1.0dB) Up Link 65dB (±1.0dB) Down Link 65dB (±1.0dB) Up Link 65dB (±1.
4. 2. Mechanical Specification Item Specifications Note Dimensions (L W H) 151mm x 191mm x 35mm (5.95 x 7.5 x 1.38 inch) Weight 2Kg 4. 3. Environment Specification Item Specifications Note Temperature -30 ~ 55℃(-22 ~ 131℉) Humidity 10 ~ 95% 4. 4. AC/DC Adaptor Specification No Items Spec 1 AC input power 90VAC ~ 264VAC, 47Hz ~ 63Hz 2 Output rated Voltage +5.5VDC/1.3A 3 Voltage Current range 2.5A ~ 0.
5. Certificates 5.1 FCC Certification Model : USHR-0819L ▪ Certificate Date : Oct. 2012 ▪ Certificate Number : Q4EUSHR-0819L 5.2 IC Certification Model : USHR-0819L ▪ Certificate Date : Oct.
6.
Guide de l'utilisateur & Manuel d’installation USHR-0819L
- Table des matières 1. Informations générales 2. Éléments du système inclus 3. Installation 4. Dépannage 5. Spécifications 6. Certificats 7. Mémo Cet appareil est conforme au paragraphe 15 de la règlementation FCC. Son fonctionnement est sujet aux conditions suivantes ; cet appareil est conforme à la licence Industry Canada-à l’exception des normes RSS. Son fonctionnement est sujet aux conditions suivantes ; (1) cet appareil ne provoque pas d’interférences nocives.
1. Informations générales 1.1. Précautions Référence : Instruction/Information pour un fonctionnement correct ATTENTION : Information aux utilisateurs afin d’éviter tout mauvais fonctionnement Avertissement : Instruction aux utilisateurs afin d’éviter tout danger inattendu 1.1.1 Ne pas faire tomber l’appareil - Risque d’endommager l’appareil et son fonctionnement 1.1.2 Ne pas installer près de source magnétique - Risque possible de mauvais fonctionnement 1.1.
1.2 . caractéristiques 1.2.1. Sommaire Cet appareil peut être installé dans des zones résidentielles, des bureaux, des entrepôts etc. . Voici une liste des avantages à se servir d’un Système de répéteur en intérieur. I. II. III. IV. Baisse le taux d’appels déconnectés Renforce le signal Améliore la qualité des données / Voix Prolonge la durée de vie des batteries des téléphones portables V.
2.
3. Installation 3.1. Schéma d’installation USHR-0819L 3.1.1. Installer l’antenne extérieure sur un point élevé afin d’éviter toute interférence de signal. 3.1.2. Installer l’antenne de service à un endroit approprié, tel qu’un mur ou un plafond. S’assurer que l’antenne n’est pas bloquée par un meuble ou un appareil domestique. 3.1.3. Utiliser les vis fournies pour installer le répéteur sur un mur et brancher l’adaptateur. 3.2.
3.3. Connexion du répéteur et de l’antenne 3.3.1. Connecter l’antenne extérieure au connecteur RVS tel qu'indiqué ci-dessous. 3.3.2. Connecter l’antenne de service au connecteur FWD tel qu'indiqué ci-dessous. 3.3.3. Brancher l’adaptateur sur une prise électrique.
3.3.4. Brancher l’adaptateur AC/DC sur le connecteur référencé DC5.6V 3.3.5. Une fois branché, 3 LED vertes vont s’allumer sur la façade avant de l’appareil, tel qu'indiqué ci-dessous.
4. Dépannage 4.1. Statut LED Élément LED VERTE LED ROUGE Référence Problème ON - Voir 4.1.1 OFF OFF Voir 4.1.2 ON - Voir 4.1.3 - ON Voir 4.1.4 OFF OFF Voir 4.1.5 ON - Voir 4.1.6 - ON Voir 4.1.7 OFF OFF Voir 4.1.8 PWR Cellulaire PCS 4.1.1. État : allumé 4.1.2. État : éteint 4.1.3. Conditions normales de fonctionnement du cellulaire 4.1.4.
5. Spécifications 5.1.
4. 2. Spécifications de l’appareil Appareil Spécifications Note Dimensions (L l H) 151mm x 191mm x 35mm (5.95 x 7.5 x 1.38 inch) Poids 2 Kg 4. 3. Spécifications du milieu Élément Spécifications Note Température -30 ~ 55℃ (-22 ~ 131℉) Humidité 10 ~ 95% 4. 4. Spécifications de l’adaptateur AC/DC No Éléments Spec 1 Puissance d'entrée AC 90VAC ~ 264VAC, 47Hz ~ 63Hz 2 Tension de sortie nominale +5.5VDC/1.3A 3 Plage courant/tension 2.5A ~ 0.
5. Certificats 5.1 Certification FCC Modèle : USHR-0819L ▪ Date du Certificat : Oct. 2012 ▪ Numéro de Certificat : Q4EUSHR-0819L 5.2 Certification IC Modèle : USHR-0819L ▪ Date du Certificat : Oct.
6.
Service Antenna Specification Model Name : PAT-CPWI-M ◆ Specification Item Horizontal Vertical ◆ Photo Specification Frequency Range 824 ∼894 MHz 1750 ∼2400MHz VSWR ≥ 2.0 : 1 ≥ 1.5 : 1 Gain ≥ 4.0 dBi ≥ 7.
Donor Antenna Specification Model Name : ALP-15QD-M ◆ Specification Item Horizontal Vertical ◆ Photo Specification Frequency Range 824 ∼894 MHz 1750 ∼2400MHz VSWR ≥ 1.8 : 1 ≥ 1.5 : 1 Gain ≥ 5.0 dBi ≥ 11.