Product Guide

Walkie Talkie
Model: 100068731
PRODUCT GUIDE
CONTROL BUTTONS DISPLAY SCREEN GUIDE
TALKING AND LISTENING MENU OPTIONS
GETTING STARTED
Installing the Three AA Batteries
1.Take the belt clip off.
2.With the back of the radio facing you, lift the battery cover latch up
and remove the cover.
Removing the Three AA alkaline battery
1.Turn the radio off.
2.With the back of the radio facing you, lift the battery cover latch up
and remove the cover.
3.Close the battery cover firmly.
To communicate , all radios in your group must be set to the same
channel and Interference Eliminator Code.
1.To talk, press and hold the PTT button. When transmitting , the
icon is shown .
2.When you are finished talking, release the PTT button.
3.When receiving, the icon is shown.
For maximum clarity, hold the radio 2 to 3 centimeters away from your
mouth and speak directly into the microphone . Do not cover the
microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range . Do not use radios closer than five feet apart.
Monitor Button
Press and hold button for 3 seconds to enter monitor mode and
listen for weak signals on the current channel .
You can also listen to the volume level of the radio when you are not
receiving . This allows you to adjust the volume, if necessary .You can
also press button to check for activity on the current channel
before you talk.
Push-to-Talk Timeout Timer
To prevent accidental transmissions and save battery life, radio will stop
transmitting if you press PTT button for 60 seconds continuously.
Mode Button
Press and hold button for 3 seconds, the user will be
seamlessly switching between two-way and weather mode.
Selecting the Channel
The channel is the frequency of the radio uses to transmit.
1.Press the button until the channel number starts to flash.
2.Press or button to change the channel number.
3.Press the PTT button to exit menu or button to continue setup.
Selecting the Interference Eliminator Code
Sub-Codes help minimize interference by blocking transmission from
unknown sources. Your radio has 121 Sub-Codes.
To set the code for a channel:
1. Press the button until the code number starts to flash.
2. Press or button to select code number.
3. Press the PTT button to exit menu or button to continue setup.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your
group when you pressed button. The radio has 10 call tones.
To set a call tone:
1.Press button until call tone ‘CA’ appears. The current call tone
setting flash.
2.Press or button to change and listen to the call tone.
3.Press the PTT button to exit menu or button to continue setup.
Voice Operated Transmission (VOX)
Transmission is initiated by speaking into the microphone of the radio
instead of pushing the PTT button.
Using the Micro-USB Charger
Note:
● Be careful when removing alkaline batteries. Do not use sharp or
conductive tools to remove either of these batteries.
● Remove the batteries before storing your radio for extended
periods of time. Batteries corrode over time and may cause
permanent damage to your radio.
● Do not mix old and new batteries and Do not mix alkaline, standard
(carbon-zinc) or rechargeable (ni -cad, ni -mh, etc.) batteries.
Note:
● Using a Micro USB charger when rechargeable batteries in place
and please combine all notes together
● Alkaline batteries are provided inside the package, do not use
Micro USB to charge alkaline batteries
● If the nickel metal hydride battery is installed, you can use Micro
USB to charge the nickel hydride battery
● It is recommended to power OFF your radio while charging.
● When moving between hot and cold temperatures, do not charge
the NiMH batteries until the battery temperature acclimates
(usually about 20 minutes).
● For optimal battery life, remove the radio from the charger within 16
hours . Do not store the radio while connected to the charger.
Turning your Radio On and Off
1.Press and hold on the button to turn your radio ON/OFF. In the
ON position ,the radio chirps and briefly shows all feature icons
available on the radio .
2.The display screen then shows the current channel, code and all
features that are enabled . The radio is in Two - Way mode.
Setting the Volume
Press and hold button for three seconds to listen to volume level.
1.First press either or to trigger volume change. You will see
current volume level on screen .
2. Press to increase the volume. Press to decrease the volume.
3. When the volume reached level 0 the mute icon appears
permanently on screen.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Note: Remove the battery from radio for storage purposes．
Radio Battery Meter
The number of bars ( ) on the radio battery icon shown indicates
the battey level . When the radio battery meter shows one segments ,
the radio chirps periodically (Low Battery Alert). In battery low status ,
the radio will sound the alert every 10 minutes or after releasing the
PTT button.
Take the belt clip off
Remove the
battery cover
Insert 3 AA
alkaline
Batteries
Close the battery
Cover firmly
3.Insert the three AA alkaline battery with + and – polarity as shown
inside.
4.Close the battery cover firmly.
Mon
Scan
Mon
Scan
Mon
Scan
LAMP
MENU
MENU
MENU
MENU
MENU
MENU
CALL
CALL
(1)May 11.2021-V1 (2)
(3)
(5)(4) (6)
(7)
The micro – USB charger is a handy port that allows you to conveniently
charge your NiMH battery . Use certified adaptor (5V,≥1A). Do not
attempt to charge alkaline batteries .
1.Make sure your radio is turned OFF.
2.Plug the micro – USB cable into the micro –USB charging port on
your radio . Connect the other end of the micro –USB charger to
wall power outlet.
3.The battery meter on LCD will move to indicate the battery is
Charging.
CALL
Mon
Scan
LAMP
MENU
Microphone
Accessary Port
Lamp
Screen
Push-to-Talk
Power On /Off
Call Tone
Lamp On/Off
Weather Switch
Speaker
Micro-USB
Charging Port
Lock
Menu
Monitor
Scan
Numbers of Channel
Call Tone
Numbers for Codes
Weather
VOX
Dual Watch
Volume Mute
Battery Meter
Scan
Lock
Status
(transmit/ receive)