Installation Instructions

ManualsBrandsOnLogic ManualsElectronicsOnLogic Go

8-inch ultra-thin Face Temperature Detection Terminal

FCC WARNING

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation. Changes or

modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable

protection against harmful interference in aresidential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Summary of content (10 pages)

PAGE 1
8-inch ultra-thin Face Temperature Detection Terminal FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 2
FCC RF warning statement: RF exposure warning: This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
PAGE 3
Aperture 4.0mm Focus 0 to 2 meters White balance Auto size 8-inch, screen Resolution 1280*800，400cd 1280 * 800, brightness 400cd Processor CPU RK3288 RAM DDR3 2GB ROM EMMC 8GB OS Andoid Android8.1 Accessories Fill light Infrared, LED lights Card reader (Reserved) card reader, ID card reader and thermal imaging temperature detection module Screen Port module full-view IPS LCD Network module Support wired, 2.4Gwifi Audio line out 1 Audio line out USB port USB2.
PAGE 4
buttons OTG port Protection level General parameters 1 port For semi-outdoor or pure outdoor use Power DC12V Operating temperature -10℃-60℃ Working humidity 10%-90% Static electricity 4K/8K Battery radiation Not exceeded Power consumption 5W MAX Equipment weight About3.5 lbs Equipment size 373.7*135*85mm Dimensions Standard body temperature Installation instructions A Instructions for appearance The schematic diagram of the gate is shown in the figure below.
PAGE 5
B Instructions for appearance ①According to the requirements of the installation site, a space of 35mm in diameter is generally opened in the middle or front of the gate, as shown in the figure, ⊕ is the recommended opening position. Single channel gate Double channel gate Note: The position of the opening should be based on the actual application and the type of gate， 35mm is only a reference .
PAGE 6
Connect the power and network cable, and the screen will start Hold the post with both hands and turn it gently to adjust the angle of the gate, as shown in the figure. According to the recognition interface, adjust the gate to the proper recognition angle For Desktop The nut needs to be removed, the tail wire is passed through the stainless steel bracket and the nut in sequence, and the angle is tightly tightened; it is suitable for program debugging.
PAGE 7
For wall-mounted ① Rotary type : Firstly, put the white 86 switch back box on the wall at 1400mm，and the specific height should depend on the actual use.And then mark the four corners of the back box with a pen, drill four holes with an impact drill, place the rubber plug in the hole, fix the back box with screws, and then do the cable.（This method is installed for surface ）If concealed installation is required, draw a hole in the four sides of the size of the back box with an impact drill.
PAGE 8
If there is any mistake with hand measure, subject to the actual product. Note: Before tightening the screws, please ensure that all the tail wires are not crushed by the screws, causing a short circuit. ②Wall-hanging type：Firstly,remove the stainless steel wall hangings from the device. And then put the stainless steel plate on the wall at an appropriate height, drill four holes with an impact drill, place the rubber plug in the hole, fix the stainless steel plate to the wall with tapping screws.
PAGE 9
outlet on the back Cable wiring diagram, as follows Switch signal Wiegand input outlet at the bottom Wiegand output signal 232 8-inch face recognition tail wire description seven gate tail wires USB2.
PAGE 10
signal 232 RJ45 wired network port 5 Wall-mounted tail wires USB2.