Firmware Updates & Instructions

ManualsBrandsOnkyo ManualsAV Receivers & AmplifiersOnkyo TX-RZ1100 THX-Certified 9.2 Channel Network A/V Receiver

Firmware Update Onkyo TX-RZ1100, TX-

RZ3100 and PR-RZ5100

(10-11-2018)

We are pleased to offer this firmware update for the best possible

performance of your Onkyo AV Receiver.

This update may be installed via USB or Network. We

recommend USB for faster, more reliable installation.

TX-RZ1100, TX-RZ3100, PR-RZ5100

(Current Version

2139-8000-5070-0010)

The 10/11/2018 update will address the following and includes

previous updates:

1. Adds support for Amazon Music.

• Amazon Music service requires that you have Amazon Prime

account or Amazon Music Unlimited account

• Onkyo Controller App is required for initial set-up of Amazon

Music.

For detail about updated function, please refer to the link below.

http://www.onkyo.com/manual/sup/upd/amazon_onk.pdf

2. Adds setting of Preset Volume for Sonos Connect.

For detail about updated function, please refer to the link below.

http://www.onkyo.com/manual/sup/upd/sonosconnect_onk.pdf

3. Adds support for pass-through function of HLG(Hybrid Log-

Gamma) HDR signal.

4.Enhanced security.

Depending on the Firmware version, update will be needed 2 times.

Summary of content (7 pages)

PAGE 1
Firmware Update Onkyo TX-RZ1100, TXRZ3100 and PR-RZ5100 (10-11-2018) We are pleased to offer this firmware update for the best possible performance of your Onkyo AV Receiver. This update may be installed via USB or Network. We recommend USB for faster, more reliable installation. TX-RZ1100, TX-RZ3100, PR-RZ5100 (Current Version 2139-8000-5070-0010) The 10/11/2018 update will address the following and includes previous updates: 1. Adds support for Amazon Music.
PAGE 2
5. Minor bug fixes and improvements stability. Previous Updates: The 8/21/2018 update will address the following and includes previous updates: 1. Enhanced security. 2. Adds support for Deezer HiFi. 3. Depending on the Firmware version, update will be needed 2 times. The 6-5-2018 update will address the following & includes previous updates: 1. Adds support for Sonos Connect (Sonos Connect required) 2. Minor bug fixes and improvements The 4/4/2018 update will address the following: 1.
PAGE 3
• Setup Guide: www.intl.onkyo.com/next_generation/setup.html Introduction of multi-room audio functions: www.intl.onkyo.com/next_generation 3. Minor bug fixes and improvements stability. The 8/31/2017 update will address the following: 1. Adds support for DTS Play-Fi. *To use Play-Fi, you need to download the application. http://www.onkyo.com/manual/sup/upd/playfi_onk.pdf Before starting to use Play-Fi, set "On" at the "Network Standby" ("NET Stby") setting.
PAGE 4
*Note for Bluetooth pairing. If Bluetooth devices were previously paired, you must pair the devices again after the Firmware update is complete. The 2/23/2017 update will address the following: 1. Improved distance measurement from the listening position and Dolby Enabled speakers. 2. Minor bug fixes and performance updates. 3. Adds baseline support for FireConnect. This update will enable streaming from Network Services /USB/ Bluetooth/Music server. *Sampling rates of 44.1 kHz and 48 kHz are supported.
PAGE 5
We hope you enjoy the improved functionality this update provides to your AV Receiver. Precautions for the Firmware Update Please read the update instructions carefully before beginning. The firmware update should take up to 30 minutes. Once the update begins, don't turn off the power supply to the A/V receiver until it is time to restart it. Depending on the conditions of the network, a firmware update via a network may take more than one hour or even fail to finish.
PAGE 6
How to prepare the USB Memory Device: 1. Download the zipped firmware update file and save to the Desktop of your computer. 2. http://download.onkyo.com/AVR0022/ONKAVR0022_HAHAHAHAHAHOHO _114.zip 3. Right click on the file and select “Extract All” and place the extracted folder on the Desktop of your computer: 1. Connect the USB Memory Device to the USB port of your computer and copy the contents of the unzipped/extracted folder onto your USB Memory Device. 2.
PAGE 7
3. Press the “Enter” button on the front panel to begin the update. 4. Do not shut the unit off until “Complete” is shown on the front display. This will take up to 30 minutes. 5. Once the update has completed check the firmware version to confirm that the unit is fully up to date. If it is not, run the update again. To check the firmware version, press the SETUP button on the front panel. Highlight “7.Misc” and press enter. Highlight “F/W Update” and press Enter.