SN29402928A_A-9150_En_1704XX.book 1 ページ ２０１７年５月１８日 木曜日 午後５時５分 Contents INTEGRATED AMPLIFIER A-9150 Introduction ...................................2 Connections.................................12 Turning On & Basic Operations....... 21 Instruction Manual Advanced Operations .................25 Others...........................................28 Thank you for purchasing an Onkyo Integrated Amplifier. Please read this manual thoroughly before making connections and plugging in the unit.
SN29402928A_A-9150_En_1704XX.book 2 ページ ２０１７年５月１８日 木曜日 午後５時５分 Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SN29402928A_A-9150_En_1704XX.book 3 ページ ２０１７年５月１８日 木曜日 午後５時５分 Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer. 3. Care—Occasionally you should dust the unit all over with a soft cloth.
SN29402928A_A-9150_En_1704XX.book 4 ページ ２０１７年５月１８日 For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.
SN29402928A_A-9150_En_1704XX.book 5 ページ ２０１７年５月１８日 木曜日 午後５時５分 Features • Three-stage Inverted Darlington Circuitry • Digital input capable of handling 192 kHz sampling rate (2 COAXIAL/2 Optical) • 384 kHz/32 bit D/A converter from Asahi Kasei • Phase Matching Bass Technology • 1.6 mm Full Flat Chassis • 60 W/ch (4 ohms, from 20 Hz - 20 kHz, 0.
SN29402928A_A-9150_En_1704XX.book 6 ページ ２０１７年５月１８日 Contents Introduction Important Safety Instructions ..........................................2 Precautions .......................................................................3 Supplied Accessories ......................................................4 Features.............................................................................5 Before Using the Integrated Amplifier ............................7 Installing the Batteries.....................
SN29402928A_A-9150_En_1704XX.book 7 ページ ２０１７年５月１８日 木曜日 午後５時５分 Before Using the Integrated Amplifier Installing the Batteries 1 To open the battery compartment, press the small hollow and slide the cover. Using the Remote Controller To use the remote controller, point it at the integrated amplifier’s remote control sensor, as shown below.
SN29402928A_A-9150_En_1704XX.book 8 ページ ２０１７年５月１８日 木曜日 午後５時５分 Getting to Know the Integrated Amplifier Front Panel For detailed information, see the pages in parentheses. 1 ÍON/STANDBY button (Ä page 21) Sets the integrated amplifier to On or Standby. 2 Remote control sensor (Ä page 7) Receives control signals from the remote controller. 3 MAIN IN LED (Ä page 19) Lights when the settings are enabled to use this unit as a power amplifier.
SN29402928A_A-9150_En_1704XX.book 9 ページ ２０１７年５月１８日 木曜日 午後５時５分 Rear Panel 1 DIGITAL IN OPTICAL D3/D4 jack Connects components such as CD players with optical digital audio output. 2 3 4 5 6 7 REMOTE CONTROL jack Connect Onkyo components such as Network Audio Player, Onkyo Docks, CD Players, or Tuner with (Remote Interactive) jacks. PHONO (MM/MC) L/R jacks Connect a turntable with analog audio output. GND screw Connects the turntable’s ground wire.
SN29402928A_A-9150_En_1704XX.book 10 ページ ２０１７年５月１８日 木曜日 午後５時５分 Remote Controller 5 SETUP button (Ä page 25, page 26) Switch to the mode for setting speaker impedance and selecting the jacks for RI docking. 6 RETURN button Returns to the previous display when changing settings. 7 MUTING button (Ä page 24) Mutes or unmutes the integrated amplifier. You can also use the remote controller to control your Onkyo CD Player, Onkyo Network Audio Player, Onkyo Dock, or Onkyo Tuner.
SN29402928A_A-9150_En_1704XX.book 11 ページ ２０１７年５月１８日 木曜日 午後５時５分 Connecting Terminal LINE1/D1 LINE2/D2 Component Button on Remote Controller CD Player TUNER NETWORK AUDIO PLAYER Í Í DIMMER DIMMER 1 Í 2 DIMMER DIMMER D/C D/C B/A B/A B/A (Preset Up/Down) ENTER ENTER 4 Í CD Í 5 DISPLAY Display the current input and settings.
SN29402928A_A-9150_En_1704XX.book 12 ページ ２０１７年５月１８日 木曜日 午後５時５分 Connections Connections The power cord must be connected only after all other cable connections are completed. Connecting Your Speakers Right Left Speakers A Integrated Amplifier Speakers B Right ∫ Screw-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.
SN29402928A_A-9150_En_1704XX.book 13 ページ ２０１７年５月１８日 Note • Make sure that the wires do not touch metal parts on the back panel or elsewhere. • Y plugs cannot be connected. • Two sets of speakers (Speakers A and Speakers B) can be connected to the integrated amplifier. You can select which speakers to output audio to when listening to music. You can also output audio from both sets of speakers. • If you use Speakers A or Speakers B, make sure to use speakers with an impedance of 4 to 16 ohms.
SN29402928A_A-9150_En_1704XX.book 14 ページ ２０１７年５月１８日 木曜日 午後５時５分 Cable and Jacks Optical digital audio OPTICAL Coaxial digital Coaxial digital connections allow you to enjoy digital sound such as Orange PCM. The maximum sampling rate for PCM input is 192 kHz/24 bit, 2ch. The integrated amplifier provides 75-ohm impedance matching. audio* Analog audio (RCA) Optical digital connections allow you to enjoy digital sound such as PCM. The maximum sampling rate for PCM input is 192 kHz/24 bit, 2ch.
SN29402928A_A-9150_En_1704XX.book 15 ページ ２０１７年５月１８日 木曜日 午後５時５分 Analog Connection Connecting a CD Player Integrated Amplifier This is an example of connection using the CD Player. Digital Connection Integrated Amplifier CD Player 1 CD Player 1 Connect the coaxial digital cable to the COAXIAL D1 jack. Tip Connect an audio pin cable to the LINE IN 1 jack. Tip • The CD player can be connected to the LINE IN 1/2/3/4 jack.
SN29402928A_A-9150_En_1704XX.book 16 ページ ２０１７年５月１８日 木曜日 午後５時５分 Analog Connection Connecting a Tuner Integrated Amplifier This is an example of connection using the Tuner. Digital Connection Integrated Amplifier Tuner 1 Connect an audio pin cable to the LINE IN 2 jack. Tuner Tip 1 Connect coaxial digital cable to the COAXIAL D2 jack. Tip • The Tuner can be connected to the COAXIAL D1 or D2 jack or the OPTICAL D3 or D4 jack.
SN29402928A_A-9150_En_1704XX.book 17 ページ ２０１７年５月１８日 Connecting a Network Audio Player and an RI dock 木曜日 午後５時５分 Analog Connection Integrated Amplifier This is an example of connection using the Network Audio Player and Onkyo Dock. Note that when connecting a network audio player and an dock simultaneously, the feature will work with only one of the devices, so connect the cable to the device you have selected to be linked.
SN29402928A_A-9150_En_1704XX.book 18 ページ ２０１７年５月１８日 Connecting a Turntable 木曜日 午後５時５分 Tip This unit is compatible with turntables using either MM cartridges or MC cartridges. You will need to switch the input setting to match the type of cartridge you are using. Refer to “Changing the input setting from a turntable to MC” (Ä page 27) for how to switch. • Connect your cassette tape deck to either of the following jacks: LINE IN 1/2/3/4.
SN29402928A_A-9150_En_1704XX.book 19 ページ ２０１７年５月１８日 Using the Integrated Amplifier as a Preamplifier The integrated amplifier can be used as a preamplifier (Pre mode). This is an example of connection using the power amplifier. Integrated Amplifier 木曜日 午後５時５分 Using the Integrated Amplifier as a Power Amplifier The integrated amplifier can be used as a power amplifier. This is an example of connection using the Onkyo preamplifier (sold separately). Only the MAIN IN jacks and SPEAKERS jacks are used.
SN29402928A_A-9150_En_1704XX.book 20 ページ ２０１７年５月１８日 Connecting the Power Cord Integrated Amplifier Supplied power cord To an AC wall outlet (Plug type varies from country to country.) AC INLET 1 2 Connect all of your speakers and components. 3 Plug the power cord into an AC wall outlet. Connect the supplied power cord to the integrated amplifier’s AC INLET. Tip • To reduce noise, do not tie signal cables together with the power cable. Wire them so that they are away from each other.
SN29402928A_A-9150_En_1704XX.book 21 ページ ２０１７年５月１８日 木曜日 午後５時５分 Turning On & Basic Operations Basic Operations Turning On/Off the Integrated Amplifier ÍON/STANDBY button Turning On the Integrated Amplifier Turning Off the Integrated Amplifier ∫ Operating with the remote controller ∫ Operating with the remote controller 1 1 Press Í. The SPEAKERS (A/B) and Input source LEDs blink, then light up after a short time. Press Í. The integrated amplifier enters Standby mode and the LED goes off.
SN29402928A_A-9150_En_1704XX.book 22 ページ ２０１７年５月１８日 Selecting Speakers A and Speakers B You can select to output sound from Speakers A, Speakers B, or both A + B (Default value is "Speaker A"). 木曜日 午後５時５分 Adjusting the Volume The default level is 0. ∫ Operating with the remote controller VOLUME / SPEAKERS button 1 A LED B LED Press SPEAKERS repeatedly on the integrated amplifier. The LED of the selected speakers lights. 1 Press VOLUME 3/4 repeatedly.
SN29402928A_A-9150_En_1704XX.book 23 ページ ２０１７年５月１８日 Selecting the Input Source You can switch inputs to select the desired source component. Choose an input from the following: D1 (Default value), D2, D3, D4, LINE1, LINE2, LINE3, LINE4, PHONO, MAIN IN The LED corresponding to the selected input will light up. Tip 木曜日 午後５時５分 Using the Direct Function By bypassing the tone control circuit, the Direct function uses the shortest path for enhanced sound quality (Default value is "On").
SN29402928A_A-9150_En_1704XX.book 24 ページ ２０１７年５月１８日 • When the DIRECT function (Ä page 23) is on, turn the function off to use the PHASE MATCHING BASS effect. Adjusting the Bass, Treble and Balance 木曜日 午後５時５分 Muting the Sound You can temporarily mute the output of the integrated amplifier. You can adjust the bass, treble and left/right output balance respectively (Default value is "Center").
SN29402928A_A-9150_En_1704XX.book 25 ページ ２０１７年５月１８日 木曜日 午後５時５分 Advanced Operations Custom Setup Setting the Auto Standby Function When the Auto Standby (ASb) function is activated, the integrated amplifier will automatically enter Standby mode if there is no operation for 20 minutes with no audio signal input (Default value: "Off" for North American models, "On" for Other Countries).
SN29402928A_A-9150_En_1704XX.book 26 ページ ２０１７年５月１８日 Connecting with Onkyo RI Components 木曜日 4 By connecting an Onkyo component with jack to the unit by using an cable and a digital cable or an RCA cable, you can link the unit's power and input selection and enable operation with this unit's remote controller (*). After connecting the unit and the Onkyo component with a digital cable or RCA cable (Ä page 15 to 17), perform the following operations.
SN29402928A_A-9150_En_1704XX.book 27 ページ ２０１７年５月１８日 木曜日 午後５時５分 ∫ Remote Control You can use the integrated amplifier’s remote controller to control your other -capable Onkyo Components, pointing the remote controller at the integrated amplifier’s remote control sensor instead of the component. To operate the CD player, point the remote controller at the CD player.
SN29402928A_A-9150_En_1704XX.book 28 ページ ２０１７年５月１８日 木曜日 午後５時５分 Others Troubleshooting First check the followings. Since the issue may be caused by other components that are connected, be sure to also check them while referring to their manuals. Further product operating procedures and FAQs (frequently asked questions) are available from the Onkyo web site.
SN29402928A_A-9150_En_1704XX.book 29 ページ ２０１７年５月１８日 Onkyo Dock 午後５時５分 Remote Controller There’s no sound. • Make sure that the Onkyo Dock is connected to the integrated amplifier properly. • Make sure that no video content is being played. • Reset the iPod. Other • When the Auto Standby (ASb) function is activated, the power of the Onkyo Dock connected via is automatically turned off (Ä page 25). Can’t control properly by using the remote controller. • Make sure that the amplifier correctly.
SN29402928A_A-9150_En_1704XX.book 30 ページ ２０１７年５月１８日 木曜日 午後５時５分 Specifications Rated Output Power (North American) (FTC) With 8 ohm loads, both channels driven, from 20 - 20,000 Hz; rated 30 watts per channel minimum RMS power, with no more than 0.08% total harmonic distortion from 250 milliwatts to rated output. (FTC) With 4 ohm loads, both channels driven, from 20 - 20,000 Hz; rated 60 watts per channel minimum RMS power, with no more than 0.
SN29402928A_A-9150_En_1704XX.
SN29402928A_A-9150_En_1704XX.book 32 ページ ２０１７年５月１８日 木曜日 午後５時５分 2-3-12 Yaesu, Chuo-ku, Tokyo 104-0028 JAPAN http://www.onkyo.com/ 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. For Dealer, Service, Order and all other Business Inquiries: Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ For Product Support Team Only: 1-800-229-1687 http://www.us.onkyo.com/ Gutenbergstrasse 3, 82178 Puchheim, Germany Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.eu.onkyo.
