Users Manual Part 2

ManualsBrandsOne World Technologies ManualsElectronicsCEILING FAN REMOTE

11 - English

ANGLED CEILING

INSTALLATION

 Carefully feed the fan’s electrical wiring through the pivot

ball, then reinstall the pivot ball on the downrod with the

flat side facing the ceiling.

 Reinstall the ground wire with the wire facing up to ensure

proper grounding, make sure the star washer is reinstalled

in the location shown below.

 Reinstall the retainer pin in the downrod.

For Canada installations, refer to the Canada

Installation Addendum and install the support

cable on the retainer pin now.

 Lift the pivot ball back to the top of the downrod until the

retainer pin is captured. Tighten the screw to secure.

NOTE: When the pivot ball is oriented correctly, it will

also cover the ground screw and will be flush with the

top of the downrod.

PIVOT BALL

FLAT SIDE UP

PIVOT BALL FLUSH WITH

TOP OF DOWNROD

DOWNROD

GROUND

SCREW

GROUND WIRE

STAR WASHER

RETAINER PIN

SCREW

For Canada installations, refer to the Canada

Installation Addendum and test the support

cable connection now.

Summary of content (7 pages)

PAGE 1
INSTALLATION  Carefully feed the fan’s electrical wiring through the pivot ball, then reinstall the pivot ball on the downrod with the flat side facing the ceiling.  Reinstall the retainer pin in the downrod. DOWNROD RETAINER PIN DOWNROD PIVOT BALL FLAT SIDE UP For Canada installations, refer to the Canada Installation Addendum and install the support cable on the retainer pin now.  Lift the pivot ball back to the top of the downrod until the retainer pin is captured. Tighten the screw to secure.
PAGE 2
INSTALLATION HANGING THE CEILING FAN BACK SIDE OF MOUNTING BRACKET WARNING: Once you begin the process of hanging the ceiling fan, do not leave the fan unattended until the installation process is complete. A falling fan could cause serious personal injury or death.  Carefully lift the assembled fan up to the mounting bracket assembly and seat the pivot ball in the mounting bracket socket. Rotate the fan as needed so the tab on the mounting bracket socket seats in the groove in the pivot ball.
PAGE 3
INSTALLATION MAKING THE ELECTRICAL CONNECTIONS WARNING: MOUNTING BRACKET Verify the power has been disconnected to both the room and the wall switch before making the electrical connections. Failure to do so could cause fire, electric shock, serious personal injury, or death. BLACK GROUND CONDUCTOR WHITE NOTICE: When shipped, the electrical wires from the ceiling fan offer enough length to accommodate only the downrod included.
PAGE 4
INSTALLATION  Place the receiver into the top of the mounting bracket with the flat side facing the ceiling. Tuck the receiver antenna and all wiring up into the mounting bracket, making sure the wires don’t become pinched.  Lift the screw cover ring up over the screws and twist counterclockwise to secure in place. SCREWS SLIDES IN FROM THIS DIRECTION ANTENNA MOUNTING BRACKET RECEIVER TOP SCREW COVER RING  Slide the canopy up into place and rotate clockwise to lock to mounting bracket assembly.
PAGE 5
INSTALLATION  Finish the assembly by screwing the finial screw on each arm into the threaded holes in the top lens cover. NOTICE: The decorative arms in the next two steps are not required for fan operation. You may skip these two steps if you do not wish to install the decorative arms. DECORATIVE ARM  Install the decorative arms using a Phillips head screwdriver. Attach one side of each arm to the center arm support using the Phillips cap screws and screw covers as shown.
PAGE 6
OPERATION  Install the CR2032 button cell battery provided into the remote control as shown. UNLOCK NOTE: The brightness of the fan light can only be controlled by the remote control. A wall-mounted dimmer switch will not change the light’s brightness.  To turn the fan on and off, press and release the fan on/off button ( ). Use the up ( ) and down ( ) arrows to cycle through the fan speeds of Low, Medium, and Hi.
PAGE 7
OPERATION SETTING THE AIRFLOW DIRECTION Choosing the correct airflow direction of the ceiling fan will enhance the fan’s performance and make its use more enjoyable. To change the direction of airflow, use the blade direction button ( ) at the top of the ceiling fan’s remote.  In cooler weather, choose a counterclockwise blade direction to provide an upward direction of air travel. This will help circulate warm air off the ceiling and back down into the room.