SCIBA2 User & Installation Manual Version 1.00 On Track Innovations Ltd. (O T I) Z.H.R Industrial Zone P.O.
SCIBA2 User & Installation Manual Revision History Version 1.00 Revision History Version 1.00 1.00 1.00 1.00 1.
SCIBA2 User & Installation Manual NOTICE Version 1.00 NOTICE This manual contains intellectual property, including but not limited, to trade secrets and know-how, operation procedures and production procedures that belong solely to OTI. Disclosure and/or use and/or reproduction of any part of the above are strictly forbidden, except under a written license from OTI.
SCIBA2 User & Installation Manual FCC Compliance Version 1.00 FCC Compliance OTI SCIBA2 FCC ID: JNX-OTI-SCIBA2 Manufacturer: On Track Innovations Ltd. This device complies with Part 15, of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
SCIBA2 User & Installation Manual FCC Declaration of Conformity Version 1.00 FCC Declaration of Conformity We, the undersigned, OTI America Address: Suite 201, 1601 S. De Anza Blvd., Cupertino, CA 95014 Telephone number: 408-252-0333 Fax number: 408-252-8414 are the Responsible Party for this Declaration, certify and declare under our sole responsibility that the following equipment: Brand OTI Type SCIBA2 Product description Contactless card reader complies with Part 15 of the FCC Rules.
SCIBA2 User & Installation Manual Table of Contents Version 1.00 Table of Contents REVISION HISTORY...................................................................................................................................A NOTICE ..........................................................................................................................................................B FCC COMPLIANCE ....................................................................................................
SCIBA2 User & Installation Manual Introduction Version 1.00 1 Introduction The SCIBA2 reader is an inexpensive, compact radio frequency communications electronic interface unit. Bi-directional RF communication to contactless smart cards, serial communication to application controller and rich set of macro commands make it the keystone in contactless smart card systems. The SCIBA2 can be integrated into existing systems.
SCIBA2 User & Installation Manual Introduction Version 1.00 Antennas The SCIBA-2 is supplied with a standard antennas with which the system was EMC certified. WARNING: It is the installer responsibility to ensure that when using the antenna kits in the United States (or where FCC rules apply), only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden in accordance with FCC rules CFR47 part 15.204.
SCIBA2 User & Installation Manual Technical Specifications Version 1.00 2 Technical Specifications Power input from 7.0 to 15VDC. Operating temperature range -20° to 70°C (-4° to 158°F). Up to two antenna RF channels. 13.56 MHz transmission frequency conforming to ISO 14443 standard. ISO 14443 Type A/B and Mifare cards support.
SCIBA2 User & Installation Manual System Configuration Version 1.
SCIBA2 User & Installation Manual System Configuration Version 1.00 3.1 SCIBA2 Reader Enclosure ABS Plastic Protection IP20 3.1.1 Standard Connectors Antenna # 1 RF Connector P8 MCX type coax connector Antenna #1 External LEDs connector P4 6-pin Molex connector pin-to-pin compatible with LEDs connector on Antenna 1. Pin 1 – LED1 2. Pin 2 – LED2 3. Pin 3 – LED3 4. Pin 4 – Buzzer 5. Pin 5 – GND 6.
SCIBA2 User & Installation Manual System Configuration Version 1.00 3.1.2 Optional Connectors External Buzzer connector P3 2-pin Molex Microfit connector 1. Pin 1 – GND/+5V 2. Pin 2 – Open collector output COM1 RS232 connector P1 RJ45 connector. 1. Pin 4 – GND 2. Pin 5 – RXD 3. Pin 6 – TXD External I/O connector P7 (Optional) 10-pin Molex connector 1. Pin 1 –GND 2. Pin 2 – +5V 3. Pin 3 – IN/OUT 4. Pin 4 – IN/OUT 5. Pin 5 – IN/OUT 6. Pin 6 – IN/OUT 7. Pin 7 – IN 8. Pin 8 – IN 9. Pin 9 – IN 10.
SCIBA2 User & Installation Manual System Configuration Version 1.00 3.1.3 LEDs LED1 Green - USB link good LED2 Red – user programmable LED3 Red – user programmable LED4 Red – user programmable LED5 Red – 5V power LED6 Green – channel 1 Antenna ON, optionally user programmable LED7 Green – channel 2 Antenna ON, optionally user programmable 3.1.4 Jumpers J1 Emergency jumper used to reset flash. 3.1.
SCIBA2 User & Installation Manual System Configuration Version 1.
SCIBA2 User & Installation Manual System Configuration Version 1.00 3.2 Antenna The SCIBA-2 is supplied with standard antennas with which the system was EMC certified. The use of other antennas requires re-testing and certification. Enclosure ABS Plastic Protection IP__ The antenna is provided with two cable tails 1. Six-wire cable tail with Molex 6 pole connector connected to the antenna’s three LEDs and buzzer 2. Coax cable tail with the MCX connector which is connected to the antenna’s RF coil.
SCIBA2 User & Installation Manual Installation Instructions Version 1.00 4 Installation Instructions 4.1 Reader Installation Install the reader in a location where it will not be subjected to excessive heat, humidity or vibration. Heavy electrical equipment should not be installed close to the reader. 4.2 Antenna Installation Mount antenna on non-metallic surface. Distance between antenna and closest metal surface should be at least 30 millimeters. Route antenna cables to reader in protective conduit.
SCIBA2 User & Installation Manual Flash Memory Programming Version 1.00 5 Flash Memory Programming 5.1 Introduction The SCIBA2 reader’s program is stored in its non-volatile Flash Memory. Application versions and updates to the SCIBA2 reader’s program may be written only at OTI. The application versions and updates can be programmed into the SCIBA2 reader’s Flash memory by the customer through use of the Flash Memory Programmer software, described in the following paragraphs. 5.
SCIBA2 User & Installation Manual Flash Memory Programming Version 1.00 5.5 Programming 5.5.1 Flash Memory Files The flash memory files, written at OTI can be loaded into the PC from CD or through the Internet. The prefix of the flash memory files is SCI5, followed by a four-character application code, followed by the date. 5.5.2 Programming Procedure 1. Run the Flash Programmer software 2. Choose the communication port 3. Press the “Load” button. A dialogue window opens, 4.