UNO Specifications Version 1.9 Notice This manual contains intellectual property including, but not limited to, trade secrets and know-how, operation procedures and production procedures that belong solely to oti. Disclosure, use, and/or production of any part of the above are strictly forbidden, except under a written license from oti. Confidential & Proprietary Version 1.
Uno Specifications FCC Compliance Version 1.9 FCC Compliance This device (Saturn 6700) complies with Part 15, of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15, subpart C of the FCC Rules.
Uno Specifications Table of Contents Version 1.9 Table of Contents FCC COMPLIANCE ......................................................................................................................................1 TABLE OF CONTENTS ................................................................................................................................2 TABLE OF FIGURES ...............................................................................................................................
Uno Specifications Table of Figures Version 1.9 Table of Figures Figure 2-1: Card Presentation ............................................................................................................8 Figure 5-1: Front View.....................................................................................................................15 Figure 5-2: Side View ......................................................................................................................
Uno Specifications Versions Table Version 1.9 Versions Table Version 1.1 1.2 Description First version Supporting operation voltage Date 2014-11-02 2014-11-10 of 8 - 45VDC instead of 2 15 VDC Adding a note regarding "Behind Panel" mounting Having only one thickness configuration (17mm thickness) instead of 17 or 25 mm 1.
Uno Specifications Introduction Version 1.9 1 Introduction The UNO is an ultra-compact, certified payment NFC Reader based on oti’s field proven technology which is specifically designed for payment and mass transit applications. Its compact design enables easy integration and installation in unattended self-service payment stations, such as ATMs, AVMs, TVMs, gaming and gambling machines, kiosks, access control gates and more. The UNO uses oti’s patented matched antenna technology.
Uno Specifications Introduction Version 1.9 1.
Uno Specifications Introduction Version 1.9 1.
Uno Specifications Basic Contactless Operation Version 1.9 2 Basic Contactless Operation When a valid contactless payment card is presented to the reader, the reader performs a payment transaction with the contactless card. If the transaction is accepted, the unit will display a row of 4 LEDs that light up in sequence and the reader buzzer will inform the user about the transaction verdict. The reader then communicates the transaction data to the Host (POS).
Uno Specifications Technical Specifications Version 1.9 3 Technical Specifications 3.
Uno Specifications Technical Specifications Version 1.9 3.2 Product Technical Specifications The performance/electrical specifications for each feature of the UNO reader are given in the table below. Table 3-1: Performance/Electrical Specifications Feature Specification RF Interface: RF Carrier Frequency 13.56 MHz RF Output 450mW ISO/IEC 14443 A&B and Mifare Full compliance ISO/IEC 15693 Vicinity Optional Micro SIM push-push Interface Communication Links: USB, RS232 USB: 2.
Uno Specifications Technical Specifications Version 1.9 Warning: Power supply minimum requirements Keeping the DC supply voltage within the specified allowed range is crucial to guarantee proper operation of the equipment. The use of AC rectified power supply source, which is not properly filtered, forms a risk of too low voltage dips and hence should be avoided. It is highly recommended to check this issue with proper tools (e.g. oscilloscope) during the reader installation.
Uno Specifications Reader models Version 1.9 4 Reader models 4.1 RS232 model The RS232 interface is implemented using a JST 10 pin connector (JST P/N BM10B-ZPDSS). The connector exposes 10 lines according to the following: 1. RS223 Rx 2. RS232 Tx 3. USB D4. Buzser 1 5. USB D+ 6. Buzzer 2 7. GND (direct) 8. Vin 9. 5V 10. GND Ext (via common mode chock) Note: the 10 pin connector optionaly support USB communication and extranl buzzer activation. This option is not in OTI standard products portfolio. 4.
Uno Specifications Reader models Version 1.9 4.3 Interface cables 4.3.1 RS232 cable A JST 10 pin connector (JST P/N BM10B-ZPDSS) is available to access the reader full interface.
Uno Specifications Reader models Version 1.9 4.3.2 USB Cable The USB cable (1.8m) has a mini-USB upstream connector on the reader side and a USB downstream connector on the host side. This cable can be in use while the reader is in USB only configuration. In this hardware configuration, the reader is USB powered, no additional power supply is required.
Uno Specifications Dimensions Version 1.9 5 Dimensions The reader’s front and side view dimensions are given in this chapter. 5.1 Front View The reader’s front view is illustrated in the figure below.
Uno Specifications Dimensions Version 1.9 5.2 Side View The reader’s side view dimensions are illustrated in the figure below.
Uno Specifications UNO Mounting Version 1.9 6 UNO Mounting While the UNO can be placed simply on the counter as a countertop reader connected to a terminal, the UNO can also be mounted as part of an unattended machine. This chapter specifies the mounting options and procedures. The UNO mounting possibilities include 3 main options, as illustrated below: 1. On panel mounting 2. Flush mounting 3.
Uno Specifications UNO Mounting Version 1.9 6.1 On Panel Mounting The image below illustrates the UNO’s on panel mounting option. Figure 6-2: UNO Mounting Studs 1. The UNO is equipped with 4 mounting studs for front panel mounting. 2. The studs and cable are inserted through holes in the front panel. The nuts are fastened over the studs from the back of the front panel, protecting against potential attempts to dismantle the unit from the front.
Uno Specifications UNO Mounting Version 1.9 3.
Uno Specifications UNO Mounting Version 1.9 6.2 Flush Mounting The image below illustrates the UNO’s flush mounting option.
Uno Specifications UNO Mounting Version 1.9 Figure 6-6: UNO Flush Mounting – Side View 1. The UNO can be mounted flush with the front panel surface. 2. The flush mounting option requires a 63x80 mm cutout in the center of the non-metallic section of the front panel. 3. A mounting holder (green) in the back of the reader is tighten the device to the panel. A gasket that is separated between the device cover and the panel keep it waterproof.
Uno Specifications UNO Mounting Version 1.
Uno Specifications UNO Mounting Version 1.
Uno Specifications UNO Mounting Version 1.
Uno Specifications UNO Mounting Version 1.9 6.3 Countertop (Desktop) mounting As the product software supports both attended and unattended usage profiles, the UNO can be used also as attended reader. In order to use the UNO in its countertop configuration you should connect it to the POS using the full interface to via the USB interface and to place it over the counter or alternatively in its cradle (if available).
Uno Specifications Contact Us Version 1.9 7 Contact Us For oti America Technical Support (US and Canada): Phone: +1-732-429-1900 9:00 am to 5:00 pm Eastern time Monday – Friday Email: support@otiamerica.com For oti Technical Support (International): Phone: +972-4-6868000 (Ext. 8090) Email: info@otiglobal.
