Vst/Pst Controller Ver. A1.
Vst/Pst Controller Ver. A1.00 FCC Compliance FCC Compliance Labeling Requirements CFR 47, FCC part 15, Sections 15, 19, 109. A device shall bear the following label in a conspicuous location on the device. a) VST/PST Controller OTI GMS FCC ID: JNX-13560M915MCON Manufacturer: On Track Innovations Ltd. This device complies with Part 15, of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
Vst/Pst Controller Ver. A1.00 Table of Contents Table of Contents FCC COMPLIANCE ............................................................................................................A TABLE OF CONTENTS............................................................................................................. 1-1 1. SAFETY REQUIREMENT ........................................................................................ 1-2 1.1 2. USA............................................................
Vst/Pst Controller Ver. A1.00 Safety Requirement 1. Safety Requirement 1.1 USA Installation of 120VAC supply to the VST/PST Controller must be done in accordance with National Electric Code (NEC) requirements. The VST/PST controller uses 120VAC power supply connected terminals in a partitioned area marked by a yellow triangle with lightning bolt indicating presence of hazardous voltage. Keep hand off this area! Warning! Unit is supplied with 120VAC plug-in power cord.
Vst/Pst Controller Ver. A1.00 VST/PST System ETU Product Overview 2. VST/PST System ETU Product Overview 2.1 Product Description The VST/PST Controller supports both long-range vehicle smart tags operating at 900 MHz and passive proximity transponders operating at 13.56MHz. It’s main use is Smart Card/Tag Payment System. It can serve as interface to a host computer or be used as a standalone unit. At the heart of the VST/PST controller lies OTI’s MCI2 PCB.
Vst/Pst Controller Ver. A1.00 VST/PST System ETU Product Overview 2.3.2 Communication: VST tag: • 915MHz. • Normal bi-directional, transmit/receive, half-duplex. • Digital data, Binary FSK. PST tag: • 13.56 MHz. • Special bi-directional, half duplex: o Controller to tag communication – AM. o Tag to controller communication – Load modulation. • Digital data, pulse width coding. 2.3.3 Antennas: 2.3.3.1 VST channel: Controller: • Detachable directional antenna. VST tag: • Integral “L” antenna. 2.3.3.
Vst/Pst Controller Ver. A1.00 Installation Requirements 3. Installation Requirements • The intended application of the system is for the commercial and or industrial uses. • The product can not be sold to the general public, but only to the system’s Operating Company. When the system is sold by the Operating Company to the customers, the Product is installed only by the professional installers, qualified (“licensed”) by the company for this purpose.
Vst/Pst Controller Ver. A1.00 Installation Requirements 3.1 PST Antenna Wiring. The PST antenna in the window panel is wired to the VST/PST Controller via BNC connector near the window panel. Wiring should be performed by qualified technetium only. The PST antenna in the window panel has a 23” coax cable terminated with a BNC connector.
Vst/Pst Controller Ver. A1.00 Installation Requirements 3.3.1 Installation Guide Lines The VST antenna should be mounted outside window counter. The antenna should be mounted horizontal facing down approximately 10 feet above road level. Connect mounting brackets to VST antenna mounting bolts. Anchor Mounting brackets to wall or ceiling using 6mm KS-Anchors. Drill and mount the anchors through the mounting bracket holes. 3.3.2 Wiring Guidelines The VST antenna panel is supplied with an SMA connector.
Vst/Pst Controller Ver. A1.00 Installation Requirements 3.4.2 Installation Guidelines The VST/PST Controller is supplied in a metal enclosure. The dimensions of the box are W = 200mm, H = 300mm, D = 80mm. Weight: 4.2Kg. The VST/PST Controller should be mounted inside the the drive thru payment window counter. The unit should be mounted at least 3 feet above floor level. 3.4.3 Wiring Guidelines 3.4.3.
Vst/Pst Controller Ver. A1.00 Installation Requirements 3.4.3.
Vst/Pst Controller Ver. A1.00 Installation Requirements 3.4.3.3 VST/PST Layout VST Transceiver LEDs LOCK REC REC MCI LEDs +7.
Vst/Pst Controller Ver. A1.00 Mechanical Installation 4. Mechanical Installation 160 mm VST/PST Controoler 220mm 340mm Box Dimensions: W = 200mm, H = 300mm, D = 80mm 8mm Cable Entries Figure 4-1: VST PST - Enclosure Layout The VST/PST Controller is intended for wall mounting. The unit should be fixed to the wall with four mounting screws through the 4x 8mm mounting holes. Unit can be mounted either indoors or outdoors. To prevent overheating the unit should not on a wall fully exposed to sunlight.
Vst/Pst Controller Ver. A1.00 Electrical Installation 5. Electrical Installation VST Antenna PST/VST Controller MCI2 In8 GND VST Transceiver P3 BK GN RG174 Coax cable Metal Partition BK 1 5 1 5 Y/GN 5 OR BN BL W R 1A H C 120VAC H C 4 120V Y/GN 4 120V Transformer 2x120VAC Input 12V3.