ONGUARD EMERGENCY PHONE MODEL: OGC-7600NA-H USER MANUAL 2021-7-15 VERSION 1-2
Copyright 2010-2012 Author:RW 1. Product Introduction 2. Motherboard Introduction 3. Functions 4. Phone operations 5. Setup 1. Product Introduction ONGUARD model no OGC-7600NA-H Emergency Phone is a LTE emergency phone. The phone covers LTE bands worldwide and can be installed and operated most countries global wise. The phone has a built-in recorder allowing operator to pre-record phone location address to be announced to emergency operator when emergency call placed.
2. The motherboard Introduction 2.1 Appearance ⑿ ⒀ ⒄ ⑾ ⑽ ⑴ ⒁ ⑼ ⑵ ⑻ ⒃ ⑶ ⑷ ⑸ ⑹ ⑺ (15) 2.2 Terminal Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
11. 12. 13. 14. 15. 16. 17. Handset terminal Power board connector Antenna terminal Key pay wire terminal GSM signal LED Power LED Record/play LED 2.3 Install 1 2 3 4 Install SIM Card, SIM card must be inserted or removed when power off. Note: The phone can dial 911 without SIM card. If no SIM card required, proceed to step 2: Connect the 3.7V lithium battery wire into the power board socket Install either a 12V to 24V DC power transformers or a 5.
Password Setup Memory Dial setup 4. Phone operations 4.
4.3: Mike Switch Switch to left position “C” for Carbon handset mike, switch to right position “E” for Electronic handset mike. 4.
Turn Dipswitch No 4 to “off” position Pickup handset, hear one beep sound If this is your FIRST TIME setup, enter the factory default password which is 9999 and hear a long beep. You are now ready to do the following setup command If you have already setup a new password, enter your password XXXX and hear a long beep, you are now ready to so the following setup commands. 5.2: Command 0: Password Setup and Delete 5.2.
operation mode, if you dial 0, the phone will dial to 18884663669 5.3.2: Command 1-2: Delete auto dial setups If you are already in Setup Mode, enter 1***#, hear a long beep, all your Auto Dial setups will be deleted If you are not in Setup Mode, repeat command X to enter Setup Mode ,then enter 1***# , hear a long beep, all your Auto Dial setups will be deleted 5.4: Command 2: Direct dial Setup & Delete 5.4.1: Command 2-1: Setup Direct Dial Numbers You can setup 10 sets of direct dial numbers.
3*0*17132228888# If you are not in setup mode, repeat command x, and enter 3*0*17132228888# Example 2 3*1*12143336666# allows *1 to be speed dialed to 12143336666 Continue to setup *2 to *9 same format as above 5.5.
5.7: Command 6: Forward Dial This command allows 4 special groups of numbers (6*0 to 6*3 )to be forwarded to another destination number. These 4 special numbers being forwarded are: 911, *911, *091 and *0987654321. And you can setup any destination number for each of these 4 numbers. 5.7.1: Command 6-1: Setup Forward Dial If you are already in Setup Mode, setup according to following example.
8*1*1# RINGTONE DETECTION “ON” (FOR FORWARD LOCATIONS) Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.