User's Manual

ManualsBrandsOmega Research and Development ManualsElectronicsSecurity/Remote Control Transmitter

Omega

RS-210-DP

OPERATION MANUAL

Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT,

INC. (the "Company"), are warranted to be free from defects in materials and

workmanship under normal use. If a product sold by the Company proves to be

defective, the Company will repair or replace it free of charge within the first year

and thereafter all parts to be repaired will be free with only a nominal charge for

Omega's labor and return shipping, to the original owner during the lifetime of the

car in which it was originally installed.

All products for warranty repair must be sent postage prepaid to Omega

Research & Development, Inc., P.O. Box 508, Douglasville, Georgia 30133, or

send via UPS to: 981 N. Burnt Hickory Rd., Douglasville, Georgia 30134, with

bill of sale or other dated proof of purchase. This warranty is nontransferable and

does not apply to any product damaged by accident, physical or electrical misuse

or abuse, improper installation, alteration, any use contrary to its intended

function, unauthorized service, fire, flood, lightning, or other acts of God.

This warranty limits the Company's liability to the repair or replacement of

the product. The Company shall not be responsible for removal and/or reinstallation

charges, damage to or theft of the vehicle or its contents, or any incidental or

consequential damages caused by any failure or alleged failure of the product to

function properly. UNDER NO CIRCUMSTANCES SHOULD THIS

WARRANTY, OR THE PRODUCT COVERED BY IT, BE CONSTRUED

AS A GUARANTEE OR INSURANCE POLICY AGAINST LOSS. The

Company neither assumes nor authorizes any person or organization to make any

warranties or assume any liability in connection with the sale, installation, or use

of this product.

This device complies with F.C.C Rules part 15. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference

and, (2) This device must accept any interference that may be received, including

interference that may cause undesired operation.

The manufacturer is not responsible for any radio TV interference caused by

unauthorized modifications to this equipment. Such modifications could void the

user’s authority to operate the equipment.

L I M I T E D L I F E T I M E W A R R A N T Y

Omega Research and Development, Inc.

P. O. Box 508

Douglasville, Georgia 30133

www.caralarm.com

07/08 MO-RS-210-DP REV0

Summary of content (9 pages)

PAGE 1
LIMITED LIFETIME WARRANTY Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the "Company"), are warranted to be free from defects in materials and workmanship under normal use.
PAGE 2
Complete Programmable Features Matrix Table of Contents Introduction/System Overview ................................................ 3-4 Valet Switch Overview ................................................................ 3 Transmitter Overview ................................................................... 4 Using the RS-210-DP System ................................................. 5 Unlocking The Doors ................................................................... 5 Remote Starting ........
PAGE 3
duration of the starter output’s for the 1st start attempt. If the engine doesn’t start on the first attempt, the system will retry up to 3 more times. With each attempt, the output will be extended by 0.2 seconds. There are four different base starter output settings. While the default-set minimum is sufficient for most vehicles; the Extended Starter Cranking Time can be used for difficult-to-start engines. This feature should only be programmed by the installer.
PAGE 4
Feature #3 Gasoline Or Diesel Engine The Blue Status Lights report the operational status of the system at all times, and also serves as a visual deterrent to break-ins and theft. Specific description of the Status Light operation may be found on pages 7-8. The Valet Switch has three main functions: • The Valet Switch can be used to turn off the remote engine starting functions of the system placing it in “Remote Start Valet Mode”.
PAGE 5
Feature #1 Remote Start Activation Pulses Factory Default Setting: 1 pulse Options: 2 pulses 3 pulses 4 pulses (press brake pedal 1x to program) (press brake pedal 2x to program) (press brake pedal 3x to program) (press brake pedal 4x to program) This feature allows you to choose the number of pulses required on the White/Blue activation wire to activate the remote start feature. This allows you to activate the remote start with external devices.
PAGE 6
Using The Valet Switch Valet Mode The system may be placed into a “valet mode” which prevents the remote start feature from being activated. It also disables confirmation chirps when unlocking the doors. Valet Mode should always be used when you do not wish for remote starting to be operated, such as when you have your vehicle serviced.
PAGE 7
Change the Feature: Step 5 After accessing the desired feature, within 10 seconds Press & Release the brake pedal equal to the option desired. • Pressing the brake pedal once typically turns the feature on; or sets the feature’s first option. The Status Light and the parking lights will flash once when this option is chosed. • Pressing brake pedal twice also typically turns the feature off; or, sets the feature’s second option. The Status Light and the parking lights will flash twice.
PAGE 8
Starting System Status The Status Light also indicates the remote start status: 4) Off = The remote starter system is off and in standby mode. 5) Flashing Slow (after sending the remote start command) = The engine is running via the remote starting system. 6) Flashing Fast (after starting the remote start sequence) = A remote start command has been received, and the system is in the process of starting the engine.
PAGE 9
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.