Bond Bridge - User manual for Bond Home application Page 1
Setup (Android) ***Note*** The Bond Home application requires the Android device to be on version 6 or greater. 1. 2. 3. 4. Make sure that you have a stable and working wireless network. Plug the Bond into an outlet. The Bond center ring light will be white while the Bond is in boot up mode. The Bond center ring light will be flashing green when the Bond is ready to be used. If the Bond light ring is not flashing green, try performing a WiFi (Green) reset. 5. Download the Bond application at 6.
Setup (Android) *** Important note *** If the Bond is unable to connect to your WiFi network, the Bond center ring light will turn orange. Please try the following: 1. 2. 3. 4. 5. Make sure you are correctly entering your password. Try a WiFi reset and try the setup process again. Try resetting your WiFi router. Unplug your Bond, wait 30 seconds, and plug it back in. If you are still having issues connecting to WiFi, please contact us at customerservice@bondhome.io.
Setup (Android) 3. Choose your Bond. 4.
Setup (Android) 5. Set Device Name & location. 6. Select Continue. 7. Choose the function/button that best represents the function of your remote to be programmed into the bond – i.e. Power On/Off, Speed, Light, etc.
Setup (Android) *** Important Note*** If your remote is an IR remote, please select “Advanced Settings”, change Signal Type to IR and click Save. 8. Begin the scanning process on the application by following the on-screen instructions and selecting Start. 9. Aim your remote at the Bond and press the button repeatedly until the Bond center ring light turns green. Please have the remote about 2 feet away from the Bond.
Setup (Android) 10. Once the Bond center ring lights turn blue, you will be asked to choose your remote from a list of remotes that matched the signal. Test them and select the best fit. 11. Select “Use this remote”. 12. Select Done.
Setup (iOS) *** Important note *** If the bond is unable to connect to your WiFi network, the Bond center ring light will turn orange. Please try the following: 1. 2. 3. 4. 5. Make sure you are correctly entering your password. Try a WiFi reset and try the setup process again. Try resetting your WiFi router. Unplug your Bond, wait 30 seconds, and plug it back in. If you are still having issues connecting to WiFi, please contact us at customerservice@bondhome.io. Adding a New device (iOS) 1.
Setup (iOS) 2. Choose your bond under and select a device type. 3. Once you are on the “About your fan” screen, where you can set the device name & location, then select Continue. 4. Choose the function/button that best represents the function of your remote to be programmed into the bond – i.e. Power On/Off, Speed, Light, etc.
Setup (iOS) *** Important Note*** If your remote is an IR remote, please select “Advanced”, change Signal Type to IR and click Save.
Setup (iOS) 5. Begin the scanning process on the application by following the on-screen instructions and selecting Start. 6. Aim your remote at the Bond and press the button repeatedly until the bond center ring light turns green. Please have the remote about 2 feet away from the Bond. 7. Once the Bond center ring lights turn blue, you will be asked to choose your remote from a list of remotes that matched the signal. Test them and select the best fit. 8. Select “Use this remote”. 9. Select Done.
*** Important note *** If you were unable to program your remote please try the following: 1. 2. 3. 4. Try changing the remote batteries. Instead of pressing and holding the function, try pressing the function repeatedly. Get closer (1 foot) or further away (4 feet) from the Bond and try again. Try pointing the remote directly at the Bond front or sides when recording. 1. The front part of the Bond unit is opposite the USB port. 5.
FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.