User's Manual

03/13
08/14
※
※
On / Off
Press and hold ( ) for 2 second and the power is off.
OFF display on screen.
Channel Select
Press or button, enter into the select mode.
Lock / Unlock Button
Channel will be locked automatically without any buttons
pressed. LCD displayed lock icon. In lock mode, the
power can be off, but channel number cannot be changed.
When locked, press and button up to 1 sec to unlock.
Unlock icon will not be showing on LCD screen.
LED/ Battery Status
Transmitter:
Receiver:
LED lights blue when the battery is sufficient.
LED lights red when the battery is insufficient.
LED lights off when no signal is received but the battery
is sufficient.
LED lights red when signal is received but the battery
is insufficient.
Battery Saving (receiver only)
The power turns off when no signal is received within 20 mins.
UP / DOWN button
Aux In (Transmitter)
Volume wheel (Receiver)
LCD screen
Antenna
1
4
2
3
5
Battery / Signal indicator
Manual
3
8
10
2
1
4
5
6
7
9
8
13
12
11
Digital Tour Guide System
Mute button
Mic. In (Transmitter)
Earphone jack (Receiver)
Hidden Mic. (Transmitter)
Power
9
6
7
8
Charging contacts
10
Battery cover
13
Strap hole
12
11
Transmitter:
Master(A)/Slave(B) mode switch
(WT-600T)
(WT-600T)
(WT-600R)
(WT-600R)
Press ( )powerkeytoturnonthedevice.Whendevice
turnedon,LCDdisplaysbatterypower, channelnumber
andMaster(A) / Slave(B)mode.
A(Master)/B(Slave) mode setting (transmitteronly)
Channel synchronizationfunction
Mode sets with switch , and reboot is required after.
When set to Master, LCD displays A.
When set to Slave, LCD displays B.
12
Channel synchronizationmodeon
‘ ‘ means channel sync function on, ‘ ‘ meanschannelsync
functionoff.
Press keytoconfirmsetting.
If the receiver failed to sync within 30 seconds, then it will resume
to the previous channel set.
When syncing the devices, the transmitters and the receivers need
to be within 3 meter radius.
※
Transmitter:
1
※
Receiver:
The receivers will receive sync signal for first 30 seconds after
device turned on, once sync successfully, flashes in purple
for 3 second then turns blue. LCD now displays channel number
synced.
Earphone requirement
This model is designed for 3.5mm stereo earphone jack only, we
recommend to use the device with earphone provided by the
supplier.
Channel synchronizationfunction
When the device is turned off, press and atthesame
timetoturnonthedevice.
Then press or tochooseentersyncmodeornot.
FCC INFORMATION
The Federal Communication Commission Radio Frequency Interference Statement includes the following
paragraph:
The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant
to part 15 of the FCC Rules.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful interference to radio communication.
However, there is no grantee that interference will not occur in a particular installation. If this equipment
dose cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user’s authority to operate the device.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operationissubjecttothefollowingtwoconditions:(1) Thisdevicemaynotcauseharmfulinterference,
and(2) thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesired
operation.
Specifications are subject to change without prior notice.
※
In A mode, press mute key to send the sync signals, and
flashes in purple.
In B mode, press mute key to search for A signal, and once
confirmed, press again to connect.
※
Transmitter:
9
9
1
9