AT-200iD-MT Audio Guide User Manual
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
Preface Thank you for the purchase of Audio Guide AT-200. This user manual contains comprehensive instructions and operation of the unit, please read it over before your use for the first time. Features High fidelity DSP technology, offering up to 20 hours stereo audio playback with built-in 2GB memory card. Access audio content through built-in speaker or external earphone jacks. 2 earphone jacks available for couple or kids and parents. Backlit display and keypad for ease of use.
AT-200 Audio Guide Earphone jack Inbuilt speaker Power/Stop button Triggering module Charging indicator OLED screen Keypad Uploading/Charging connector Battery door Illustration 1. Earphone jack, stereo, 3.5 mm 1 or 2 headphones are valid for more than 1 user. 2. Triggering module In addition to inbuilt IR triggering mode, various triggering options (RFID/RF/ GPS) are offered respectively upon demands. 3. Charging indicator Red/Green LED indicator stands for charging/fully charged status.
AT-200 Audio Guide 4. Inbuilt speaker Users can listen to audio commentaries through the inbuilt speaker. However, this function will be disabled when the player connects with headphones. 5. OLED screen Triggering modes, battery status, volumes, photos of exhibits, and playing tracks/progress will display on the OLED screen. 6.
AT-200 Audio Guide Operation Power ON/OFF Press and hold power button for 1 second until a beep to power on. Press and hold the button for 2 seconds until an OFF sign shown in display and beeps twice to power off. (* Alarm is still working even audio guide is off.) Auto Power OFF When audio guide is not operated for 30 minutes (factory default), it will switch off automatically. (* Alarm is still working.) Auto Power Off can be changed or defined through software “Audio Master G2”.
AT-200 Audio Guide Access to additional audio content ( level) You can listen to additional audio content for a particular track by simply pressing key during the playback and then entering required number code. To exit from level, press key again after the additional audio content stops playing. Audio contents for level can be defined in Audio Master G2. Plan a programmed tour Visitors can follow a pre-programmed audio map to simplify their trips.
AT-200 Audio Guide Information key “ ” key is served as default information. It can be audio and/or picture format. Battery and Charge When battery power is almost exhausted, a low battery icon will blink and show in display. The audio guide will automatically switch off in 20 seconds. Please allocate it onto charger as soon as possible. Alarm When alarm is performed at audio guide, it will generate a continuous beep. The audio guide will be locked and can’t be operated as a result.
Loop Controller LT-200 Alarm Trigger / Alarm Trigger Optional 6 1 2 3 4 1 Power switch 2 Player ON button 3 Player OFF button 4 Alarm 1 button 5 Alarm 2 button 5 10 9 8 7 6 Coverage (trigger) adjustment 7 Loop antenna connection 8 Induction loop connection 9 Output connection, for loop amplifier 10 Power input socket (DC IN) Operation Installation Connect power supply with the device well. Build a triggering zone with supplied loop wire (please refer to installation example).
Loop Controller LT-200 Alarm Trigger / Alarm Trigger Optional OUTPUT Connection When the maximum triggering coverage can’t meet your requirement, you can connect a loop amplifier with this device trough OUTPUT connection jack 9 to increase triggering coverage. Installation of Loop Wire Arrange a triggering zone with factory supplied loop wire is recommended. In order to obtain better triggering performance, the supplied loop wire shall be ran out completely.
Loop Controller LT-200 Alarm Trigger / Alarm Trigger Optional II. Multiple sets antenna layout Antenna A and B shall keep away from each other for at least 4 meters. B >4 m A Example for allocation of antenna and alarm trigger Audioguide will beep when it comes close to alarm trigger within 2 m.
Loop Controller IT-200 IR Trigger/ Alarm Trigger 1 2 3 Optional 4 6 5 1 Power indicator 2 Power switches (DIP) and power mode setup 3 Hanging hole 4 Track number setup 5 Battery door 6 DC input socket Operation Power On Any DIP switch 2 moves to ON position will turn this device on. Power indicator 1 will light up for 2 seconds and then off. Indicator will blink every 2 seconds when device is working. Power OFF When all DIP switches 2 move to OFF (downward) position, the device will be turned off.
Loop Controller IT-200 IR Trigger/ Alarm Trigger COVERAGE setting Set a desired IR triggering range with DIP switch. A table below gives all possible settings and respective functions. DIP Status Power OFF OFF ON P1 ON P2 ON P3 ON P4 Optional IR signal coverage on application (Fig. 1) (Fig. 2) P1 (Max coverage) > P2 > P3 > P4 (Min coverage) Power Supply Insert 2 AA batteries or connect with factory supplied power adapter (5V / 1A). ※ Adapter can't charge battery.
Loop Controller iD-200 RFID Tag / Alarm Trigger Optional RFID (Radio Frequency Identification) Tag; Proximity Tag How to operate RFID (Proximity) Tag Each tag can be programmed with one number code, from 0000 ~ 9999, through RFID tag writer (optional). Following tips of number code are helpful to plan your audio tour. 0000: served as “audio guide OFF”. 951 - 982: served as “language number code”. 0001 - 9999: served as “audio track number”.
Caution / Troubleshooting / Maintenance Caution 1. DON'T operate the device in the rain or in humid circumstance. 2. Prevent the device from dropping. 3. Employ factory supplied Li-Poly battery only, to prevent feasible damage and danger. 4. DON'T tear battery apart in case it explodes. 5. Dispose battery with insulated package in case it explodes. Troubleshooting No Sound Make sure audio guide is uploaded / duplicated with audio content. Make sure memory card is available in device.