Order Number : GETEC-C1-14-179 FCC Part 15 subpart B Test Report Number : GETEC-E3-14-039 Page 1 / 1 APPENDIX G : USER’S MANUAL EUT Type: CENTRAL PROCESSOR FCC ID.
Owner’s Manual CP-2 Central Processor
ccGEN2 CP-2 Owner’s Manual ©2013 Universal Remote Control, Inc. The information in this owner’s manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this owner’s manual may be subject to change without prior notice.
TABLE OF CONTENTS Introduction 1 Features and Benefits 1 Parts Guide 1 Front Panel Descriptions 2 Rear Panel Descriptions 3 Installing the CP-2 4 Specifications 8 Limited Warranty Statement 9 End User Agreement 11 Federal Communication Commission Interference Statement 12 Declaration of Conformity 13
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Introduction Congratulations on purchasing the ccGEN2 CP-2 Central Processor for automation and control. Using the ccGEN2 line of interfaces provides you full access and control for every compatible device using IR, IP, RS-232, and Relays. This network based control is also compatible with URC sensors, like audio sensor and video sensor, which detects the status of a device and provides automation triggers.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Front Panel Descriptions The front panel consists of two indicator lights which illuminate when in use. Power LED Ethernet LED Power LED: Indicates that the CP-2 is powered on when lit. Ethernet LED: Indicates the network connectivity status: ● On = Connected ● Off = Not connected ● Blinking = Attempting to connect.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Rear Panel Descriptions The rear panel ports are: LAN DC 12V Power IR Outputs: #1-6 Reset RS-232 Ports Relay: NO, NC, COM Sensors RFTX-1 DC 12V Power: Attach the included 12V power supply here. LAN Connection: RJ45 standard Ethernet connection to the local network. Relays (NO, NC, COM): Programmable relay to be normally opened (NO), normally closed (NC) or momentary contact. An application shall require less than 30V/.5A.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Installing the CP-2 Physical Installation of the CP-2 and Accessories The CP-2 Central Processor can be installed anywhere in the home or office network. Once installed, program it to operate all local equipment using IP/Network, IR, RS-232, or Relays. As well as query the status of a device using Sensors. All cables are plugged into their respective ports in the rear of the unit. Network Installation 1.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Optimizing IR Flasher Levels Test a few commands for each device before fixing the flasher in place on the front panel of a device. Since Satellite Receivers and Cable Boxes are extremely sensitive to IR overload or saturation, you should test them thoroughly. Put up the cable or satellite on-screen guide and test the navigation arrows. Compare operation via RF to the original remote control. Operation should be identical.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Using Sensors with the CP-2 The CP-2 uses sensors to detect audio, light, video, voltage, current and contact closures to determine the equipment status, query the state of a device or other automation triggers for the equipment it controls. For example, using a video sensor cable with the CP-2 can detect a video signal from a composite or component video output.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Wiring to the Relay on the CP-2 The CP-2 has a Relay with three contacts, NO, NC, and COM. These can be used as dry contacts or to an electrical switch or motor for use with screens, blinds, curtains, etc. The Relay can be programmed as either a latching or a momentary contact. Using an RFTX-1 for URC One-Way Lighting products The CP-2 can use an RFTX-1, via the available RFTX-1 port. It controls URC One-Way Lighting products at 418 or 433.92 MHz.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Specifications Network: One 10/100 Ethernet port Relay: One relay configurable to be NO, NC or Momentary Sensor: Two Sensors support Video (SEN-VID), Voltage (SEN-VOLT), Audio (SEN-AUD), Current (SEN-CMF), Light (SEN-LITE), and Contact Closure (SEN-CCLS) sensors. RS-232: Two RS-232 ports support TX, RX and GND two-way communication via URC cables.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Limited Warranty Statement 1. Limited Warranty and Disclaimers Universal Remote Control, Inc. (“URC”) warrants that the URC equipment shall be free from defects in material and workmanship under normal usage for one (1) year from purchase when such is purchased from URC. This limited warranty is valid only in the United States of America.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER SKILL AND CARE, OR OUTCOME OR RESULTS. WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE OTHER PROVISIONS HEREIN, WARRANTY DOES NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT OR ACTS OR NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH THIRD PARTY CONTENT (IV) BEYOND THE WARRANTY PERIOD AND/ OR FAILURE TO FOLLOW URC WARRANTY CLAIM PROCEDURE.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER URC’s PC programmable remotes or any of our Total Control® whole-house equipment are authorized for online internet sales. Buying URC’s PC programmable remotes or any of our Total Control® whole-house equipment online means buying equipment that does not have a URC’s limited warranty. Such equipment is not eligible for URC tech support or software support, either. 2.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CCGEN2 CP-2 ADVANCED NETWORK SYSTEM CONTROLLER Declaration of Conformity Company Name : OH SUNG ELECTRONICS CO., LTD.
NOTE Page 14
NOTE Page 15
500 Mamaroneck Avenue, Harrison, NY 8528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.
