Order Number : GETEC-C1-20-742 FCC Part 15 subpart C Test Report Number : GETEC-E3-20-089 Page 1 / 1 APPENDIX H : USER’S MANUAL EUT Type: Remote Controller FCC ID.
C009 RCU MANUAL 1 - Mechanical Address: #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA TEL: 82-54-468-7063 / FAX: 82-54-461-8368 http://www.ohsungec.
C009 RCU MANUAL 1.2 - Dimensions 1.
C009 RCU MANUAL 1.4 – Barcode label It is attached to the PCB and it can be seen into the battery compartment after removing the battery cover. 1.5 - Packing 1.5.1 - Remote Control - PE bag dimensions : 80 x 250mm (LDPE 0.05t) - Weight: 60g (without battery) 1.5.2 - Carton box - Box dimensions : W 600 x D 400 x H 200 mm - Quantity: 140pcs - Box weight: TBD 1.5.
C009 RCU MANUAL - Pallet weight: TBD 2 - Electrical 2.1 - Electrical Characteristic Parameter Condition Spec Unit Frequency Range Bluetooth 2.402 ~ 2.480 [GHz] Channel Low Energy 40 [Num] RF Power Specification 4 [dBm] 19 [Num] PAvg -20~+10 [dBm] PMax +8 [dBm] Pmin -20 [dBm] 225~275 [KHz] ≥ 185 [KHz] Test channel RF Power ∆f1 avg Modulation ∆f2 avg Characteristic ∆f2/∆f1 s ∆f2min TC-3000 (RF measuring instrument) 0.8 ≥ 92.
C009 RCU MANUAL IR Range Direct ≥12 [m] Horizontal 7 (±15°) [m] -30~-14 [dB] -30~-10 [dB] -30~-14 [dB] 300Hz VOICE 2KHz Voice Inspection JIG 3.8KHz 2.2 - Battery Management a) Remote Control sends the information for battery level using Bluetooth battery service. b) Level of LVD is 2.1V ±0.1V. c) If the battery voltage as reached the LVD value, Remote Control cannot enter the pairing mode and the factory reset mode. d) If the battery voltage is under 2.0V, Remote Control does not operate.
C009 RCU MANUAL 3 - Software 3.1 - Bluetooth 5.0 LE identification a) Device Name: RemoteG20 b) Vender ID: 0x0957 c) Product ID: 0x0001 d) Vendor ID Source : Blutooth SIG e) Hardware Version : 'V', '1', ’.’, '0' 3.2 - Pairing mode & Re-pairing mode a) If user presses the [HOME] + [BACK] keys on the Remote Control for more than 4 secs, the Remote Control enters pairing mode. b) The green led stays on while pressing and holding the keys.
C009 RCU MANUAL UUID 0x12, 0x18,0x0F, 0x18 Human Interface Device Battery Complete local name RemoteG20 Device Name 3.4 - Scan Response Data Item Data Complete local name RemoteG20 Detail Device Name 3.5 - Un-Pairing mode a) Un-pairing from the STB clears Remote Control bonding cache. b) Remove Device bonding cache (manual approach - Optional): Press and hold [BACK] key while inserting batteris. 3.
C009 RCU MANUAL key presses may be discarded until the cached event is successfully passed to the STB. 3.8 - Key codes for STB a) In Bluetooth mode, HID Profile is used.
C009 RCU MANUAL Home KEYCODE_HOME 0x47 0x0C 0x0223 TV(Guide) KEYCODE_GUIDE 0x32 0x0C 0x008D Volume + KEYCODE_VOLUME_UP 0x23 0x07 0x0080 Program ∧ KEYCODE_CHANNEL_UP 0x33 0x0C 0x009C Mute KEYCODE_VOLUME_MUTE 0x25 0x0C 0x00E2 Volume - KEYCODE_VOLUME_DOWN 0x24 0x07 0x0081 Program ∨ KEYCODE_CHANNEL_DOWN 0x34 0x0C 0x009D YOUTUBE KEYCODE_F18 0x64 0x0C 0x0077 NETFLIX KEYCODE_F17 0x63 0x0C 0x0078 APP03 KEYCODE_F19 0x67 0x0C 0x0079 APP04 KEYCODE_F20 0x68 0x0C 0x0
C009 RCU MANUAL 3.11 - Voice Search initiated by the Remote Control (On-request, legacy) a) For Voice function, it is recommended to be more than 10meters from the receiver. b) Distance between mouth and microphone should be between 5 to 30cm. c) If [ASSISTANT] key is pressed, the Remote Control sends the START_SEARCH command first followed by the HID_KEY_EVENT to the STB and the STB sends back the MIC_OPEN command to the Remote Control.
C009 RCU MANUAL Note: The "On-request" assistant interaction model must be supported by all Remote Control and it should be used by default before any other interaction model is negotiated by GET_CAPS , CAPS_RESP messages exchange. 3.12 - Voice Search initiated by the Remote Control (PTT, Press-to-Talk) a) For Voice function, it is recommended to be more than 10meters from the receiver. b) Distance between mouth and microphone should be between 5 to 30cm.
C009 RCU MANUAL f) Flow chart. 3.13 - Voice Search initiated by the Remote Control (HTT, Hold-to-Talk) a) For Voice function, it is recommended to be more than 10meters from the receiver. b) Distance between mouth and microphone should be between 5 to 30cm. c) If [ASSISTANT] key is pressed and held down, the green led turns on d) The Remote Control sends the AUDIO_START command and transmits the voice data.
C009 RCU MANUAL 3.14 - Voice Search initiated by the launcher a) For Voice function, it is recommended to be within 10meters from the receiver. b) Distance between mouth and microphone should be between 5 to 30cm. c) User selects and validates the voice search on the launcher by using navigation and [DPAD CENTER] keys. d) The Remote Control sends the HID_KEY_EVENT to the STB and the STB sends back the MIC_OPEN command to the Remote Control.
C009 RCU MANUAL 3.15 - Couch mode a) If a key or multiple keys are pressed continuously for more than 30s, the Remote Control stops transmission in order to protect the battery discharge. 3.16 - OAD mode a) OAD proceeds according to the Telink specification.
C009 RCU MANUAL Note1 : OAD Data = Index(2byte) + Data(16byte) + CRC(2byte) Note2 : Check Byte is last index and inverse of last index.
C009 RCU MANUAL b) The green led blinks 2times to confirm that it is deleting the existing pairing table, ir setting value. c) When the factory reset is completed, the green led goes off and the Remote Control operate as ir. 4 - IR over BLE 4.
C009 RCU MANUAL 4.3 - IR Programming Operation Sequence a) ATV writes 0x01 to IR_PROG_CONTROL to START an IR programming session. This invalidates any previously started session. b) For each key that ATV wants to program: 1) ATV writes the corresponding key ID to IR_KEY_ID. The key ID is 2 bytes. Keys are identified by Android key codes and are always written in ascending key code order. The remote should ignore any key codes that it does not support. 2) ATV writes the corresponding IR code to IR_CODE .
C009 RCU MANUAL KEY_DOWN and KEY_UP events. b) Notifications shall be sent only for keys in IR mode. 5 - Environmental Tests 5.1 - Temperatures Conditions - Operating Temperature: 0°C ~ +45°C - Storage Temperature: -10°C ~ +60°C at 95% Humidity 6 - Mechanical Tests 6.1 - Drop Test - Floor Material: Wood - Test Method: Drop the sample from a height of 76cm with batteries instalLED.
C009 RCU MANUAL - Weight: 230g for rubber sheet - Test quantity: 2EA and 2 keys / EA for rubber sheet - Required level: The printing is not faded or destroyed. 7 - Certification Assesment of compliance of the product to the requirements relating to Electromagnetic Compatibility is based on the following standards: - EN 62368-1:2014 + A11:2017 - ETSI EN 301 489-1 V2.1.1:2017 (Published) / ETSI EN 301 489-1 V2.2.0 (Draft) - ETSI EN 301 489-17 V3.1.1:2017 (Published) / ETSI EN 301 489-17 V3.2.
C009 RCU MANUAL ❑Reorient or relocate the receiving antenna. ❑Increase the separation between the equipment and receiver. ❑Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ❑Consult the dealer or an experienced radio/TV technician for help. Warning! Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.