Order Number : GETEC-C1-20-463 FCC Part 15 subpart C Test Report Number : GETEC-E3-20-070 Page 1 / 1 APPENDIX H : USER’S MANUAL EUT Type: Remote Controller FCC ID.
C008 RCU MANUAL 1 - Mechanical 1.1 - Pictures Address: #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA TEL: 82-54-468-7063 / FAX: 82-54-461-8368 http://www.ohsungec.
C008 RCU MANUAL 1.2 - Dimensions 1.3 - Materials & colours PART NAME TOP/BOTTOM CASE BATTERY COVER NAVI KNOB OK KNOB WINDOW FILTER RUBBER BUTTON DESCRIPTION MATERIAL MATERIAL MATERIAL MATERIAL MATERIAL MATERIAL EXCEPT FOR DESIGNATED FORMING COLOR EXCEPT FOR DESIGNATED PRINT COLOR PRINT COLOR (ASSISTANT/HOME) FORMING COLOR (ASSISTANT/HOME) YOU TUBE hulu NETFLIX DISNEY + SUFACE TREAMENT Address: #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA TEL: 82-54-468-7063 / FAX: 82-54-461-8368 http://www.ohsungec.
C008 RCU MANUAL 1.4 - QR code label It is attached to the PCB and it can be seen into the battery compartment after removing the battery cover. 1.5 - Packing 1.5.1 - Remote Control - PE bag dimensions : 80 x 250mm (LDPE 0.05t) - Weight: 60g (without battery) 1.5.2 - Carton box - Box dimensions : W 600 x D 400 x H 200 mm - Quantity: 140pcs - Box weight: 11.
C008 RCU MANUAL Quantity Date code Purchase Order number Box ID 1.5.3 - Pallet - Pallet itself dimensions: W 1200 x D 800 x H 140mm - Overall pallet dimensions: W 1200 x D 800 x H 1340mm - Quantity per pallet: 2,800pcs (4 boxes / layer - 5 layers) - Pallet weight: 240Kg - Label / Packing list with barcode attached on each pallet - Data as follows: Manufacturer name Manufacturer part number Quantity Date code Purchase Order number Pallet ID 2 - Electrical 2.
C008 RCU MANUAL ∆f2rate ≥ 99 [%] Carrier fTx-fn ≤ 150 [KHz] Frequency ∆f0-fn ≤ 50 [KHz] Offset and f1-f0 ≤ 20 [KHz] Drift ∆fn-f(n-5) ≤ 20 [KHz] Operating Voltage RF (Bluetooth) 2.2~3.6 [V] LVI Voltage Low Voltage Indicate 2.25±0.
C008 RCU MANUAL 3 - Software 3.1 - Bluetooth 5.0 LE identification a) Device Name: RemoteG10 b) Vender ID: 0x (TBD) c) Product ID: 0x (TBD) d) Vendor ID Source : Blutooth SIG e) Hardware Version : 'T', 'L', ' ', 'V', '0', '1' 3.2 - Pairing mode & Re-pairing mode a) If user presses the [HOME] + [BACK] keys on the Remote Control for more than 4 seconds, the Remote Control enters pairing mode. b) The led stays on while pressing and holding the keys.
C008 RCU MANUAL 3.4 - Scan Response Data Item Data Detail Complete local name RemoteG10 3.5 - Un-Pairing mode a) Un-pairing from the STB clears Remote Control bonding cache. b) Remove Device bonding cache (manual approach - Optional): Press and hold [BACK] key while inserting batteris. 3.6 - Connection Parameter (TBD) a) Connection Interval Time: ms b) Connection Slave Latency: (sec) c) Connection Supervision Time Out: sec 3.
C008 RCU MANUAL b) In IR Mode, NEC format is used - Structure of the NEC format: Custom Code - Data - Inverse data - Custom Code : 0x8877 - Code list : IR code Key Name Android key code for BT HID code Costom Code : 0x8877 HID Usage Page Usage ID Power KEYCODE_POWER 0x21 0x0C 0x0030 Input KEYCODE_TV_INPUT 0x60 0x0C 0x01BB Bookmark KEYCODE_BOOKMARK 0x74 0x0C 0x022A Assistant KEYCODE_ASSIST 0x46 0x0C 0x0221 Dashboard KEYCODE_APP_SWITCH 0x71 0x0C 0x01A2 D-pad Up KEYCODE_DPAD_UP
C008 RCU MANUAL AF01F617B664 3.10 - ATV Voice initialization (Capability) a) After the Remote Control device is paired and connected, the STB will send it a command to get capabilities of the Remote Control. b) This command will be sent via the ATVV_CHAR_TX characteristic. c) The Remote Control should then respond back with its capabilities using ATVV_CHAR_CTL notification. d) Flow chart 3.
C008 RCU MANUAL transmits the voice data for 15sec timeout duration. e) After timeout duration or the Remote Control receives the MIC_CLOSE command from the STB, the Remote Control sends the AUDIO_STOP command to the STB and the led goes off. f) Flow chart. Note: The "On-request" assistant interaction model must be supported by all Remote Control and it should be used by default before any other interaction model is negotiated by GET_CAPS , CAPS_RESP messages exchange. 3.
C008 RCU MANUAL e) After timeout duration or the Remote Control receives the MIC_CLOSE command from the STB, the Remote Control sends the AUDIO_STOP command to the STB and the led goes off. f) Flow chart. 3.13 - Voice Search initiated by the Remote Control (HTT, Hold-to-Talk) a) For Voice function, it is recommended to be more than 10 meters from the receiver. b) Distance between mouth and microphone should be between 5 to 30cm.
C008 RCU MANUAL 3.14 - Voice Search initiated by the launcher a) For Voice function, it is recommended to be within 10 meters from the receiver. b) Distance between mouth and microphone should be between 5 to 30cm. c) User selects and validates the voice search on the launcher by using navigation and [DPAD CENTER] keys. d) The Remote Control sends the HID_KEY_EVENT to the STB and the STB sends back the MIC_OPEN command to the Remote Control.
C008 RCU MANUAL 3.15 - Couch mode a) If a key or multiple keys are pressed continuously for more than 30s, the Remote Control stops transmission in order to protect the battery discharge. 3.16 - OAD mode a) OAD proceeds according to the Telink specification.
C008 RCU MANUAL Note1 : OAD Data = Index(2byte) + Data(16byte) + CRC(2byte) Note2 : Check Byte is last index and inverse of last index.
C008 RCU MANUAL c) When the factory reset is completed, the led goes off and the Remote Control operate as ir. 4 - IR over BLE 4.
C008 RCU MANUAL This invalidates any previously started session. b) For each key that ATV wants to program: 1) ATV writes the corresponding key ID to IR_KEY_ID. The key ID is 2 bytes. Keys are identified by Android key codes and are always written in ascending key code order. The remote should ignore any key codes that it does not support. 2) ATV writes the corresponding IR code to IR_CODE . The IR code might be split into multiple consecutive writes. Payloads shall be concatenated in the order of arrival.
C008 RCU MANUAL 5 - Certification 5.1 - FCC Assesment of compliance of the product to the requirements relating to Electromagnetic Compatibility is based on the following standards: - FCC Part 15 subpart C 7.2 – Manufacturer & Importer 5.2.1 – Manufacturer - Name: Ohsung Electronics Co., Ltd. - Address: #181 Gongdan-dong, Gumi, Gyeongbuk Republic of Korea. 5.2.
C008 RCU MANUAL FCC Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.
