Order Number : GETEC-C1-17-175 FCC Part 15 subpart C Test Report Number : GETEC-E3-17-014 Page 1 / 1 APPENDIX H : USER’S MANUAL EUT Type: Remote Controller FCC ID.
B702 Manual Contents 1 - Mechanical Requirements 1.1 - Design 1.2 - Picture …………………………………………………………… Page 2 …………………………………………………………… Page 2 …………………………………………………………… Page 2 2 - Electrical Requirements 2.1 - Electrical Characteristic …………………………………………………………… Page 3 …………………………………………………………… Page 3 3 - Software Requirements …………………………………………………………… 3.1 - Bluetooth 4.0 LE Identification …………………………………………………………… 3.2 - Pairing mode …………………………………………………………… 3.3 - Re-pairing mode …………………………………………………………… 3.
B702 Manual 1 - Mechanical Requirements 1.1 - Design - Dimensions : 160 x 47 x 17.8mm 1.2 - Picture (for reference only) Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.
B702 Manual 2 - Electrical Requirements 2.1 - Electrical Characteristic Parameter Condition [GHz] 2.402 ~ 2.480 Frequency Range Bluetooth Low Energy Specification Channel [Num] 40 RF Power 0 Test channel 19 [dBm] [Num] [dBm] PAvg 0±5 PMax +5 Pmin -5 ∆f1 avg 225~275 [KHz] 225~275 [KHz] 0.
B702 Manual 3 - Software Requirements 3.1 - Bluetooth 4.0 LE identification a) Device Name: LMT Remote b) Vender ID: 0x02AF c) Product ID: 0x2008 3.2 - Pairing mode a) At first time pairing or after Factory Reset, RCU works only in IR. b) Press [OK] and Google [HOME] keys for longer than 4 seconds. LED stays ON while pressing [OK] and Google [HOME] keys. c) After 4 seconds, the LED starts blinking so that to confirm the remote has entered into pairing mode.
B702 Manual e) If the user presses any key during pairing mode, excepted Up, Down, Left, Right and OK keys, the remote stops pairing and the previous paired status is restored, f) If pairing with new device is not successfully made for 90 seconds, the LED goes ON for 4 seconds and then goes OFF. The previous paired status is restored. 3.4 - Factory Reset mode a) Press [Google] and [OK] keys for longer than 4 seconds. LED stays ON while pressing [Google] and [OK] keys.
B702 Manual recommended) c) User selects and validates the voice search on the launcher by using navigation and OK keys. d) STB sends the voice search START command to the remote. e) The LED starts blinking, the remote transmits the voice data for 10sec timeout duration. f) After timeout duration, the remote sends the END command to the STB and the LED is turned off. Note: if any key is pressed within the timeout duration, the remote stops transmitting the voice data and activate the pressed key event. 3.
B702 Manual - Structure of the NEC format: Custom1 - Custom2 – Data – Inverse data For MUTE to be seen as 0x16-0x20-0x25.
B702 Manual 4 - RF Standard Conformity Assesment of compliance of the product to the requirements relating to Electromagnetic Compatibility is based on the following standards: - EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 - ETSI EN 301 489-1 V1.9.2:2011 - ETSI EN 301 489-17 V2.2.1:2012 - ETSI EN 300 328 V1.9.
B702 Manual Federal Communication Commissions (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.