Order Number : GETEC-C1-17-532 FCC Part 15 subpart C Test Report Number : GETEC-E3-17-052 Page 1 / 1 APPENDIX H : USER’S MANUAL EUT Type: Remote Controller FCC ID.
B526A Manual 1 - Mechanical Requirements 1.1 - Design - Dimensions : 160 x 47 x 17.8mm TOP CASE BOTTOM CASE BATTERY COVER RUBBER BUTTON MATERIAL ABS MATERIAL COLOR BLACK PRINT COLOR SMI-G 715 (BLACK) MATERIAL ABS MATERIAL COLOR BLACK MATERIAL SILICONE RUBBER FORMING COLOR BLACK FORMING COLOR 4-A TRANSLUCENT CLEAR PRINTING COLOR WHITE SURFACE TREATMENT SILICONE COATING Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.
B526A Manual 1.2 - Picture (for reference only) Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.
B526A Manual 1.3 - Batch Number Adhesive label is attached at the inside part of the battery cover 1.4 - Packing 1.4.1 - Packing Process - PE bag dimensions : 83 x 286 mm (LDPE 0.05t) - Quantity Per Box: 140pcs - Box dimensions : W 600 x D 400 x H 200 mm 1.4.
B526A Manual 2 - Electrical Requirements 2.1 - Electrical Characteristic Spec Unit 2.402 ~ 2.480 [GHz] 40 [Num] 0 [dBm] 19 [Num] PAvg 0±1 [dBm] PMax +1 [dBm] Pmin -1 [dBm] ∆f1 avg 225~275 [KHz] ≥ 185 [KHz] Parameter Condition Frequency Range Channel RF Power Bluetooth Low Energy Specification Test channel RF Power ∆f2 avg Modulation Characteristics ∆f2/∆f1 TC-3000 (RF measuring instrument) ∆f2min ≥ 92.
B526A Manual 3 - Software Requirements 3.1 - Bluetooth 4.2 LE identification a) Device Name: Channel Master Remote b) Vender ID: 0x02AF c) Product ID: 0x2025 d) Software Version : V0007 3.2 - Pairing mode a) At first time pairing or after Factory Reset, RCU works only in IR. b) Press [OK] and [APPS] keys for longer than 4 seconds. LED stays ON while pressing [OK] and [APPS] keys. c) After 4 seconds, the LED starts blinking so that to confirm the remote has entered into pairing mode.
B526A Manual d) If pairing is successfully made, the existing pairing table is deleted, the LED goes OFF and the remote works in Bluetooth with the new device. e) If the user presses any key during pairing mode, excepted Up, Down, Left, Right and OK keys, the remote stops pairing and the previous paired status is restored, f) If pairing with new device is not successfully made for 90 seconds, the LED goes ON for 4 seconds and then goes OFF. The previous paired status is restored. 3.
B526A Manual Note: if any key is pressed within the timeout duration, the remote stops transmitting the voice data and activate the pressed key event. 3.7 - Voice Search initiated by the launcher a) For Voice function, it is recommended to be within 5 meters from the receiver. b) Distance between mouth and microphone should be within 40 cm (15~20cm recommended) c) User selects and validates the voice search on the launcher by using navigation and OK keys.
B526A Manual and [V-] keys. b) After 4 seconds, LED will be blink 3 times. c) Press 01 to remove the TV setting. Or press 02 to remove the Audio setting. d) LED will be blink 3 times to confirm the remote has remove the setting. 3.10 - Couch mode a) If a key or multiple keys are pressed continuously for more than 30s, the remote stops transmission (except pairing combination) in order to protect the battery discharge. 3.11 - OAD mode a) OAD proceeds according to the RTK specification. 3.
B526A Manual Volume - - - - - DVR KEYCODE_MEDIA_SELECT_HOME 0xA0 0x0C 0x009A Channel + KEYCODE_CHANNEL_UP 0x33 0x0C 0x009C Channel - KEYCODE_CHANNEL_DOWN 0x34 0x0C 0x009D Rewind KEYCODE_MEDIA_REWIND 0x51 0x0C 0x00B4 Play/Pause KEYCODE_MEDIA_PLAY_PAUSE 0x52 0x0C 0x00CD Fast Forward KEYCODE_MEDIA_FAST_FORWARD 0x53 0x0C 0x00B3 1 KEYCODE_1 0x01 0x07 0x001E 2 KEYCODE_2 0x02 0x07 0x001F 3 KEYCODE_3 0x03 0x07 0x0020 4 KEYCODE_4 0x04 0x07 0x0021 5 KEYCODE_5 0
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
