RLP0003 User Manual Module Maker Foxconn Module Maker Model Name NFA765 Manufacturer PN T99H294.02 TP(Chip vendor) Qualcomm TP Product Name WCN6856 F/W Version TBD H/W Version dp25-19296-102_c_design_package,_cca,_wcn6856.m2.hp04. 3,_nfa765-040,_hastingsprime_2x2_11ax_bt_5.2_pcie_usb,_m .2_2230_e_key,_bt_pldr_only,_full_build.zip Standard WLAN 802.11a/b/g/n/ac/ax and BT 5.
System Requirements Laptop/ PC containing: 32-bit PCI Express Bus 32 MB memory or greater 300 MHz processor or higher Microsoft Windows 10 Profile Management Configure the wireless network adapter (wireless card) from the Profile Management tab of the Client Utility.
Create or Modify a Configuration Profile To add a new configuration profile, click New on the Profile Management tab. To modify a configuration profile, select the configuration from the Profile list and click the Modify button. The Profile Management dialog box displays the General tab. In profile management: Edit the General tab. Edit the Security tab. Edit the Advanced tab. To configure a profile for ad hoc or access point (infrastructure) mode, edit the Network Type field on the Advanced tab.
profiles in the Available Profiles box. 3. Highlight the profiles to add to auto profile selection, then click Add. The profiles appear in the Auto Selected Profiles box. Ordering the auto selected profiles: 1. Highlight a profile in the Auto Selected Profiles box. 2. Click Move Up, Move Down, or Remove as appropriate. The first profile in the Auto Selected Profiles box has highest priority, and the last profile has lowest priority. 3. Click OK. 4. Check the Auto Select Profiles box. 5.
Import and Export Profiles Importing a Profile 1. From the Profile Management tab, click the Import button. The Import Profile window appears. 2. Browse to the directory where the profile is located. 3. Highlight the profile name. 4. Click Open. The imported profile appears in the profiles list. Exporting a Profile 1. 2. 3. 4. From the Profile Management tab, highlight the profile to export. Click the Export button. The Export Profile window appears. Browse to the directory to export the profile to.
Scan Available Networks Click the Scan button on the Profile Management tab to scan for available infrastructure and ad hoc networks. On this list, click Refresh to refresh the list at any time.
Tray Icon The tray icon appears at the bottom of the screen, and shows the signal strength using colors and the received signal strength indication (RSSI). Hold the mouse cursor over the tray icon to display the current configuration profile name and association, as well as transmit and receive speed and the wireless adapter name and IP address. Right-click on the tray icon to: Help Open the online help. Open Client Launch the Client Utility (ACU).
Show Connection This window displays connection information: Status Active Profile Displays the active configuration profile name. Auto Profile Shows whether auto profile selection is enabled. Selection Connection Status Displays whether the adapter is connected to a wireless network. Link Quality Lists the quality of the link connection. SSID Displays the SSID of the associated network. Access Point Name Shows the name of the AP the wireless adapter is connected to.
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
6.525-6.875GHz 2.42 6.875-7.125GHz 1.48 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2AQ68RLP0003”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.
OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules.
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 24374-RLP0003".
Avertissement: Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment : (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis pour les dispositifs ut
DETACHABLE ANTENNA USAGE This radio transmitter [IC: 24374-RLP0003] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
6.875-7.125GHz 1.48 The antenna-to-user separation distance must be greater than 20cm. To ensure compliance with the Radio Frequency (RF) exposure guidelines, this device must be used at least 20 cm away from your body or nearby persons. Failure to observe this warning could result in the RF exposure levels exceeding the applicable limits. The distance between each antenna should more than 50 mm when integrated in the host to ensure the simultaneous transmission compliance.
