User Manual MOB1 Maritime Survivor Locating Device English
© 2014 Ocean Signal Ltd The technical data, information and illustrations contained in this manual were believed to be correct at the time of print. Ocean Signal Ltd reserve the right to change specifications and other information contained in this manual as part of our continual improvement process. No part of this manual may be reproduced, stored in a retrieval system or transmitted in any form, electronic or otherwise, without the prior permission of Ocean Signal Ltd.
MOB1 USER MANUAL IN CASE OF EMERGENCY Use only in situations of grave or imminent danger NOTE: Refer to section 5.4 for deactivation instructions. 3 Version 00.
MOB1 USER MANUAL CONTENTS IN CASE OF EMERGENCY ............................................................................................................................3 1. GENERAL ....................................................................................................................................5 1.1 Introduction................................................................................................................. 5 1.2 Exposure to RF Electromagnetic Energy ...............
MOB1 USER MANUAL 1. GENERAL 1.1 Introduction The rescueME range of products provides the user with the latest technology specifically designed for compact size and ease of operation. 1.2 Exposure to RF Electromagnetic Energy This product also complies with EN62479 (EU) and RSS-102 (Canada). This product has been evaluated for compliance with the FCC RF exposure limits given in CFR 47 part 1.307(b) at a distance of greater than 2cms. 1.
MOB1 USER MANUAL 2. Lifejacket Installation If your rescueME MOB1 is not already pre-installed lifejacket, please follow the instructions below carefully. • Loop the strap through the operating clip. • Clip the bracket to the MOB1 so that the MOB will be on the outside of the inflation tube. The following diagrams assume that the mounting is to the left of the inflation tube. On most occasions it is preferable to mount to the outside of the tube.
MOB1 USER MANUAL • Arm the MOB. Once the MOB is fully attached to the life-jacket, you are ready to arm the device. • Testing • MOB Installation sticker 3. MMSI configuration 3.1 Self Identification The MOB1 is supplied with the self identification number pre programmed. This number is specific to each MOB1 and cannot be changed. The MMSI displayed on the AIS receiver will always start with ‘972’ irrespective of the country it was purchased in. 3.
MOB1 USER MANUAL entered, a second box for a group MMSI will appear. Enter you group MMSI here if available. On completion press the Update Device button to proceed. A new screen with further instructions will appear. Slide the arming key down to the armed position and fit the black rubber programming adaptor so that the push button is over the test key and the aperture is over the clear indicator window. To put the MOB1 into programming mode, press the test key for at least fifteen seconds.
MOB1 USER MANUAL 4. MOB1 OVERVIEW 1) Antenna behind activation slide 2) Activation slide 3) Manual Activation Button 4) Arming Slide (in safe position) 5) Strobe and Indicator LED 6) Test (and Off) button 7) Arming Slider (in armed position) 1 2 3 4 3 5 6 7 MOB1 Controls shown in activated condition 9 Version 00.
MOB1 USER MANUAL 5. OPERATION WARNING: Use only in situations of grave and imminent danger. Misuse may result in a severe penalty. Ensure that your MOB1 is always fitted with an unused battery that is within the marked expiry date. Failure to do so may result in reduced operating time when used in a real emergency. Please observe the recommendations on testing in section 06. 5.1 Automatic Activation When correctly packed in a lifejacket the MOB1 will automatically activate when the lifejacket inflates.
MOB1 USER MANUAL • Press and hold the ON key for over 5 seconds to transmit a single DSC All Ships Distress Alert. This should only be done in a dire emergency, if it is obvious that your alert is not being acted upon by you own vessel. After the key is pressed, the Green LED will start flashing then become steady. Release the key to commence transmission of a single DSC transmission.
MOB1 USER MANUAL 6. TESTING Routine testing of your MOB1 is recommended to ensure it is in good working order if needed, but please follow the guidance notes below on the frequency that tests should be carried out. Please remember that each test will reduce the battery capacity slightly and reduce the operation time of your MOB1 during an emergency. 6.1 Beacon test To test your MOB1 is functioning correctly, press and hold the TEST key for one second.
MOB1 USER MANUAL The AIS/GPS test should only be attempted with a clear view of the sky. 13 Version 00.
MOB1 USER MANUAL APPENDIX 6.4 Maintenance and Troubleshooting Your MSLD will require little maintenance except periodic cleaning, if required. Always use a damp cloth to clean the case and dry thoroughly. Do not use solvents or other cleaning fluids as this may cause the plastics to deteriorate. Ensure the antenna is free to unwind. 6.5 Batteries The MOB1 contains Lithium batteries for long operating life.
MOB1 USER MANUAL 6.8 Specifications AIS transmission Transmit Power (EIRP ...............................................................................................................1Watt Frequency ............................................................................................ 161.975/162.025MHz ±500Hz Baud rate ............................................................................................................................ 9600baud Synchronisation ..............................
MOB1 USER MANUAL 6.9 Approvals TBD 6.9.
MOB1 USER MANUAL 17 Version 00.
MOB1 USER MANUAL 6.10 Limited Warranty Your Ocean Signal MOB1 is warranted against manufacturing defects in materials and workmanship for a period of 5 years from the date of purchase and in accordance with the following conditions. Ocean Signal will at its discretion, repair or replace faulty product free of charge excluding the cost of shipping. Proof of purchase shall be required in order for a warranty claim to be valid from the original purchaser.
MOB1 USER MANUAL 19 Version 00.