Network Bullet Cameras Quick Guide V1.
Waterproof Requirements Please waterproof cables in accordance with the following instructions. User shall assume all responsibility for device damage caused by water due to improper waterproof measures. NOTE! Before you start, connect all the needed cables and cut off the copper wires for the cables that you don't use. Please use self-adhesive waterproof tape (supplied with some products) to protect the cables. Use waterproof components to protect the network cable.
. Install the supplied waterproof components to the network cable in sequence. CAUTION! You need to mount the rubber ring onto the network cable interface first. 4. If your camera has a DC cable and you will not use it, insert the plug into the interface. DC interface Plug 5. (Optional) After the waterproof treatment is completed, put the cables into a waterproof junction box (purchased separately). CAUTION! The cable connector must not be exposed and must be kept away from water.
1 Packing List Contact your local dealer if the package is damaged or incomplete. The attachments may vary with models, please see the actual model for details. No. Name Qty Unit 1 Camera 1 PCS 2* Screw components（1） 1 Set 3* Mount accessory （2） 1 Set 4 User manual 1 Set Remarks: * means optional and supplied with certain models only. (1)Including one or more accessories such as screws and hex key.
proper margin reserved to avoid poor port contact or loosening caused by shock or shake. During transportation, special attention is required to protect the transparent dome cover from friction, scratch and stain, etc. Do not remove the protective film from the cover until mounting is finished. Remove the protective film before powering on the device. Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself.
3.2 Cable Connection The appearance and tail cable may vary with device model. Power interface Network interface IP Network 4 Mount Your Camera 4.1 (Optional) Insert Micro SD Card For cameras that support Micro SD, you need to insert the Micro SD card after opening the bottom cover of camera. Do not hot plug the Micro SD card after it is inserted. Otherwise the camera or the SD card might be damaged. For recommended SD card specifications, please contact your dealer or technical support. 1.
Micro SD slot 4.2 Wall Mount You can adopt wall mount or ceiling mount and purchase hardware accessories by yourself. The following part takes wall mount as an example. Ceiling mount is similar to wall mount and therefore is omitted here. 1. Locate the positions of the holes. (1) Paste the drill template on the wall and align the cross center to the hole in the wall. 1 Paste the installation positioning sticker(2) on theLead wall and the across thealign cables cross center to the hole on the wall.
3. Mount the plastic rivets of self-tapping screws. Knock the plastic anchors of self-tapping screws into the guide holes and ensure that they are tightened up. 4. Screw the locknut to loosen the universal joint before attaching your camera to the wall. Locknut 5. Mount your camera onto the wall and connect all cables. Lead tapping screws through the guide holes in the base and fix them on the wall by using a screwdriver. 6. Attach the rubber sheath to the antenna.
Antenna Interface Rubber Sheath 7. Rotate the antenna to the antenna interface according to clockwise direction. Antenna Interface Antenna Reset 8. Adjust the monitoring direction. (1) Adjust the opening of the universal joints as required. (2) Rotate the spherical hinge of the camera to get the desired monitoring direction. (3) Tighten the locknut. 1 3 2 1 Adjust the opening of the universal joints as required.
5 Startup After you have installed the device, connect one end of the power adapter (purchased separately) to power supply, and then connect the other end to the power interface to start up the device. 6 Access Your Camera 1. Open your Web browser, enter the camera's IP address in the address bar, and then press Enter. The default IP is 192.168.1.13. 2. In the login page, enter the default username and password (admin/123456), then click Login. NOTE! DHCP is enabled by default.
Disclaimer and Safety Warnings Copyright Statement No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from our company (referred to as us hereafter). The product described in this manual may contain proprietary software owned by our company and its possible licensors.
and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for a particular purpose, and noninfringement. Users must assume total responsibility and all risks for connecting the product to the Internet, including, but not limited to, network attack, hacking, and virus.
Choose username and password discretely: Avoid using the username and password of your social media, bank, email account, etc, as the username and password of your device, in case your social media, bank and email account information is leaked. Restrict user permissions: If more than one user needs access to your system, make sure each user is granted only the necessary permissions.
Use a UL certified power supply that meets LPS requirements if an adapter is used. Use the recommended cordset (power cord) in accordance with the specified ratings. Only use the power adapter supplied with your device. Use a mains socket outlet with a protective earthing (grounding) connection. Ground your device properly if the device is intended to be grounded.
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
