Network Bullet Cameras Quick Guide V1.
Safety and Compliance Information Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the Safety Instructions supplied with your equipment before installation and operation. Installation This device is a class B product and may cause radio interference. Take measures if necessary. Make sure the camera operates in an environment where the temperature and humidity meet requirements.
mounting is finished, remove the film before the device is powered on. Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. Maintenance Caution: There will be risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Regulatory Compliance FCC statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. LVD/EMC/RE Directive This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU and 2014/53/EU.
Default IP, Username and Password Default IP address: 192.168.1.13 Default username: admin Default password: 123456 The default password is used for your first login. To ensure account security, please change the password after your first login. You are recommended to set a strong password (no less than eight characters). Packing List Contact your local dealer if the package is damaged or incomplete. The attachments may vary with models, please see the actual model for details.
62.42mm 90.10mm 62.67mm 39.00mm 39.00mm 162.45mm 31.00mm 8.
For specifications, see the latest product datasheets. Press and hold the RESET button for at least 15 seconds to restore factory default settings. Perform this operation within 10 minutes after the device is powered on or the reset will fail otherwise. Mount Your Camera (Optional) Insert the Micro SD Card For cameras that support Micro SD, you need to insert the Micro SD card after opening the bottom cover of camera. Do not hot plug the Micro SD card after it is inserted.
Wall Mount You can adopt wall mount or ceiling mount and purchase hardware accessories by yourself. The following part takes wall mount as an example. Ceiling mount is similar to wall mount and therefore is omitted here. 1. Locate the positions of the holes. 2. Drill holes on the wall. 1 Paste installation positioning 1 Use a Ø 6-6.5mm drill bit. stickers on the wall and align the cross center to the hole in the wall. 2 Drill 30 mm-depth guide 2 Lead the cables across the hole on the wall. 3.
Knock the plastic rivets into the guide holes and ensure that they are tightened up. Locknut 5. Mount your camera onto the wall and connect all cables. 6. Rotate the antenna to the antenna interface according to clockwise direction. Antenna Interface Antenna Reset Lead tapping screws through the guide holes in the base and fix them on the wall by using a screwdriver. 7. Adjust the monitoring direction. 8. Power on your camera and adjust images.
1 3 2 1 Adjust the opening of the universal joints as required. 2 Rotate the spherical hinge of the camera to get the desired monitoring direction. 3 Tighten the locknut. The preceding installation process is for concealed installation, during which holes are punched on the wall and cables are penetrated into the wall. If open installation is adopted, cables are not penetrated into the wall but threaded out from the outlet on one side of the base.
Open your browser, input the IP address of your camera in the address bar and then press Enter to open the login page. Enter the username and password and then click Login. Install the ActiveX at your first login. When the installation of the ActiveX is completed, open your IE to log in. For your first login with Windows 7, if the system does not prompt you to install ActiveX, follow these steps to turn off UAC: click the Start button, and then click Control Panel.