NPCS650 INSTRUCTION MANUAL WIRELESS HD RECEIVER
CONTENT WHAT'S INCLUDED...............................................................................................................3 PRODUCT OVERVIEW TRANSMITTER............................................................................3 PRODUCT OVERVIEW RECEIVER.....................................................................................4 TRANSMITTER INSTALLATION.........................................................................................5 RECEIVER INSTALLATION.....................
WHAT'S INCLUDED Digital Wireless HD Transmitter USB Power Cable Digital Wireless HD Receiver Instruction Manual 1 x 100-240V AC Power Adapter to Mini USB Quick Start Guide Right Angle HDMI Adapter Lifetime Customer Support 1 Year Warranty 2 x Screws/Screw Anchors PRODUCT OVERVIEW TRANSMITTER HDMI Input LED Indicator USB Power Input Pairing/Info Button 3
PRODUCT OVERVIEW RECEIVER Power Button with LED Indicator Info Button Status LED Unused LED HDMI Power Input HDMI Out 4
TRANSMITTER INSTALLATION • Connect the Transmitter directly to the HDMI output on a PC, cable box or any HDMI device. • Connect the Transmitter to power using the USB cable provided or connect the power adapter to the mini USB port on the Transmitter and plug it in to an available wall outlet. • HDMI USB You may also connect the Right Angle HDMI Adapter for easier setup with certain computers.
RECEIVER INSTALLATION RCA Receiver VIDEO 1 HDMI CABLE COMPONENT HDTV • Connect the HDMI cable to the HDMI Output of the Receiver and to your HDTV television or HD projector. • Ensure your TV or projector is powered ON and is in "HDMI input" mode. • Connect the power adapter to the DC Input of the Receiver and plug into a wall outlet. When the unit is successfully connected, the Power LED indicator on the POWER button lights up in WHITE.
LED BEHAVIOR FUNCTION STATUS BEHAVIOR SOLID WHITE CONNECTED Transmitter/Receiver is connected. FLASHING WHITE CONNECTING Transmitter/Receiver are searching for connection. SOLID ORANGE STANDBY Receiver is in standby mode. SLOWLY FLASHING ORANGE PAIRING Receiver is in pairing mode • If the system is unable to establish a connection within 80 seconds, the connection has been lost or the Transmitter is out of range. Verify the distance between the Transmitter and Receiver.
STANDBY MODE Press the POWER button on top of the Receiver to go from “Active mode” to “Active Standby mode”. When the transmitter is connected to power the Receiver will wake and reconnect. INFO BUTTON Press the INFO button on the Receiver or Transmitter. The Signal Quality, Source, Channel and Resolution will be displayed on the OSD for your reference. Press the INFO button again to exit. COMPUTER DISPLAY OPTIONS You can change the display option in the computer’s display settings.
PAIRING INSTRUCTIONS The NPCS650 Transmitter and Receiver come paired. If re-pairing is necessary use the below steps to reconnect the units. • Press and hold down the power button LED on the Receiver and plug in the power adapter. Release the Power button once the power LED blinks orange. HDMI • Plug the power adapter into the Transmitter. Press and hold down the pairing button. • The Power LED should be flashing white. The white flashing speed will begin to slow down.
WALL MOUNTING 1. Drill pilot holes using drilling template included below. 2. Insert the supplied two anchors into the wall. 3. Insert two screws into the anchors. Leave 1/8” length for mounting the Transmitter or Receiver. 4. Remove the rubber feet from the NPCS650. Place NPCS650 main holes over the protruding screws and slide down into position. DRILLING TEMPLATE Note: This template is to scale.
TROUBLESHOOTING PROBLEM POWER LED is not lighting up SOLUTION Make sure the power is connected to the Receiver/Transmitter. Check that the power supplies are connected to a working power outlet. Some TV/Camera USB ports may not power TX/Receiver. The POWER LED of the Receiver should be WHITE and the LED Indicator of the Transmitter should be WHITE. No Video is displayed Check the status of the Link LEDs, and check TV or projector are working normally.
Bad Audio/ No Audio Make sure that the source is outputting supported audio formats. Make sure that the TV’s volume is turned UP and not on MUTE. Make sure that your PC / Laptop audio volume has been turned UP. Make sure that your PC / Laptop audio output has been switched to HDMI out. Make sure there is no 5.8GHz wireless phone within 50cm of the Receiver. Some phones use substandard transmission schemes.
SPECIFICATIONS Wireless Technology GigaXtreme Technology System Requirements Any laptop or desktop system containing an HDMI port including popular models from these manufacturers: Alienware, Asus, Lenovo, Dell, HP, Acer, Apple (display port cable not included) HDMI, Mini-USB Operating temperature: 0° to 40° C, Storage temperature -10 ~ +55° C, Relative humidity: 15 ~ 80% RH 5V DC and USB TV: 1080p, 1080i, 720p, 576p, 480p PC : 1024x768, 1280x1024, 640x480, 800x600 Uncompressed 7.
FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
for the device and its users or bystanders to satisfy RF exposure compliance requirements. Receiver should be installed and operated with minimum distance 20cm between the radiator & your body RECEIVER For operation within 5.15-5.25 GHz / 5.47-5.725 GHz frequency range, it is restricted to indoor environment. The band from 5600-5650 MHz will be disabled by the software during the manufacturing and cannot be changed by the end user.
SAFETY INFORMATION Read all instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug.
WARRANTY Thank you for choosing Nyrius! We guarantee your investment in our products is a solid one. Our products come with a complete one-year parts and labor warranty. High performance components combined with quality craftsmanship allow us to maintain the highest possible production standards. All items are guaranteed against defects in materials and craftsmanship.
