User's Manual

ManualsBrandsNyko Technolgies ManualsElectronicsNetwork Extender

Thank you for purchasing NYKO's Wireless Net Extender™ -- the "Invisible Ethernet Cable". This unique

product provides a wireless replacement for long Ethernet cables, at a fraction of the cost of current

wireless network equipment. The Base Unit and the Remote Unit are factory matched to one another.

They will not connect or interfere with another Wireless Net Extender set, nor with any other wireless

product. Though this product is designed for wireless online gaming with PlayStation®2 and Xbox

™

, this

10Base-T system can also be used with computers, printers, and any other Ethernet enabled devices.

The Base and Remote Units have a range of up to 100 feet (30 m) and can transmit through most walls,

roofs, and floors. Therefore, no costly network wiring installations are required. The Wireless Net

Extender offers the ultimate in true Plug-n-Play -- just plug in the power and Ethernet cable and it's GAME

ON -- no drivers, no software and no configuration.

NYKO

and WIRELESS NET EXTENDER

™

are trademarks of NYKO Technologies, Inc. PlayStation®2 is a registered

trademark of Sony Computer Entertainment Inc. Xbox

™

is a trademark of Microsoft Corporation. This is a NYKO product and

is not endorsed, manufactured or distributed by the companies listed above.

BASE

REMOTE

EMOT

Base Unit

Contents

Remote Unit

Power

Supply

120V AC to

4V DC Transformer

Ethernet

Cable

6.5 ft (2 m) RJ45

Features:

•  Connects to high-speed internet without cables

•  No programming or setup -- factory configured -- plug in and

play

•  Secure encrypted communication with factory matched pairs

•  Use multiple sets within the same area

•  Can be used for connecting most any Ethernet product: printers,

scanners, laptops, game consoles, PCs, etc. up to 100 feet

• 1.5 Mbps, low latency RF wireless link.

• Can also be used with hubs, switches or routers.

Definitions:

Game Console: Any Ethernet enabled gaming device such as

PlayStation®2 or Xbox

™

Network Device: Any Ethernet enabled device. Examples

include: Game Consoles, PCs, laptops, printers and scanners.

System Requirements:

•  The user must have a DSL or Cable Modem with an active

account.

•  This product is designed for Ethernet enabled PlayStation® 2 or

Xbox

™

game consoles; it can also be used with computers,

network printers and other Network Devices.

•  The model numbers of Ethernet Adaptors for the current Game

Consoles are as follows:

 - PlayStation®2: Network Adaptor - Model # SCPH-10281

 - Xbox

™

: Ethernet built in

1 - Base Unit (1 slider switch + 2

Ethernet ports)

1 - Remote Unit (1 Ethernet port)

2 - Wall Power Adaptors (120V AC 60Hz

7W to 4V DC 300mA)

2 - Ethernet Cables 6.5 feet (2m), RJ45

1 - Instruction Manual

Quick Start Guide

Quick Start Guide STEP 1

STEP 2

Netw ork Device

Personal Computer, Video Game Console, Etc.

Netw ork Device

Personal Computer, Video Game Console, Etc.

DSL or

Cable Modem

DSL or

Cable Modem

Test the

current network

configuration using

standard Ethernet

cables.

STEP 1. Pre-installation

Test:

 Test your wired Ethernet

connection by using your

computer to access the Internet

via a DSL or Cable Modem. For

example, go to www.nyko.com

to confirm connection. (Note:

Dial-up connections using a 28K

or 56K modem are not Ethernet

connections.)

 Test your wired Ethernet

connection by using your game

console to access the Internet.

Play one online game to confirm

connection.

Note: You can use the Ethernet

cables supplied with the Wireless

Net Extender, or your current

standard Ethernet cables.

STEP 2: Setup for Wireless/Remote

Connection

1. Turn off the Network Device (Game Console, computer,

printer, or any other device).

2. Turn off or unplug the DSL/Cable Modem.

3. Plug in all devices as shown in this illustration. All power

adaptors MUST plug into a 120 VAC, 60 Hz source.

4. The Ethernet Cable from your DSL or Cable Modem

MUST plug into the left Ethernet port on the Base Unit.

5. Ensure that the Slider Switch on the Base Unit is set to

the GAME CONSOLE position.

6. Power up the DSL/Cable Modem -- then power up the

Network Device.

7. GAME ON. Setup is complete.

Netw ork Device

Game Console

any other

Ethernet enabled device

Netw ork Device

Personal Computer, Video Game Console, Etc.

Base Unit

Switch

Position

Remote Unit

DSL or

Cable Modem



GAME

CONSOLE

COMPUTER

Summary of content (2 pages)

PAGE 1
Quick Start Guide STEP 1. Pre-installation Test: TE MO RE Netw ork Device Test your wired Ethernet connection by using your computer to access the Internet via a DSL or Cable Modem. For example, go to www.nyko.com to confirm connection. (Note: Dial-up connections using a 28K or 56K modem are not Ethernet connections.) E BAS STEP 1 Personal Computer, Video Game Console, Etc. or Test your wired Ethernet connection by using your game console to access the Internet.
PAGE 2
Simple Wireless Setup OPTIONAL Pow er Adaptor Netw ork Device Netw ork Device OTHER CONFIGURATIONS: The best way to understand NYKO's "Wireless Net Extender" is to view it as an "Invisible Ethernet Cable". Refer to the “Simple Wireless Setup”, "Multiple Netwrok Devices: Sharing a Net Extender" and "Multiple Net Extenders" illustrations for additional ways the Wireless Net Extender can be used.