DT-DJ7A Audio Phone User Manual 2 Read this manual carefully before using the product, and keep it well for future use.
1. Parts and Functions Indicator 5.43 inch Unlock button Talk Button Talk volume controller 2 Tune volume controller Call button/Unlock 2nd button 0.69 inch 3.54 inch Side View Key functions Unlock button Press it to release the door; In setup mode, press it to exit the setup state. Talk button In standby mode, long press it to enter setup mode; During called state, press it to communicate hands free with visitor; In setup mode, press it to switch a group of ring tunes.
ON SW+ SW- L2 L1 1 2 3 4 5 6 7 8 9 10 11 12 L2 L1 DIP ON 1 2 3 4 5 6 7 8 9 10 11 12 DIP 2. Terminal Descriptions SW+ SW- L1, L2: Bus terminal. SW+, SW-: Door bell call button connection port. DIP: Bit-1~7: Used to User Code setting or Extended Address setting(Bit-10 set to ON). Bit-8~9: Used to Slave Monitor Address (Bit-10 set to OFF). Bit-11: Set to ON if the monitor is at the end of the line;Otherwise, set to OFF. Bit-12: Reserved. 3. Unit Mounting 1).
4. Operation Instructions 1) Door release function: When visitor calls from outdoor station, the monitor rings, press Talk button to talk with the visitor, then press the Unlock button to open the door. If the system connect 2 locks, press Call button/Unlock 2nd button to open the second door. 2) Inner call: When the monitor is in standby mode, press Call button/Unlock 2nd button to activate the inner call. 5. Setup Instructions 5.
Bit State ON User Code DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 Code=10 Code=11 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 Code=21 Code=29 DIP 1 2 3 4 5 6 7 8 9 10 11 12 Code=30 DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON Code=28 DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON Code=20 User Code DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON Code=19 DIP 1 2
5.2.2 When Bit-10 set to ON, the Bit-6~7 are used to extended address setting: Bit State ON User Code DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 ... ON DIP DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON DIP 1 2 3 4 5 6 7 8 9 10 11 12 ... ON DIP DIP 1 2 3 4 5 6 7 8 9 10 11 12 ON Code=2 DIP 1 2 3 4 5 6 7 8 9 10 11 12 ...
2). Press and hold Talk button in standby mode to enter the state of ring tune setting, and then each time you press Talk button to switch a group of ring tunes. Three groups ring tunes cycle: Group1 press Talk button Group2 press Talk button Group3 press Talk button 3). If there isn’t any operation within 10s, or press any button, it will exit the setting. ● Power Supply: DC26V ● Power Consumption: standby 4.