Datasheet

ManualsBrandsNXP SEMICONDUCTORS ManualsLinear ICsHTSH5601ETK,118

1. General description

The HITAG product line is well known and established in the contactless identification

market.

Due to the open marketing strategy of NXP Semiconductors there are various

manufacturers well established for both the transponders / cards as well as the

Read/Write Devices. All of them supporting HITAG 1 and HITAG 2 transponder IC's. With

the new HITAG S family, this existing infrastructure is extended with the next generation of

IC’s being substantially smaller in mechanical size, lower in cost, offering more operation

distance and speed, but still being operated with the same reader infrastructure and

transponder manufacturing equipment.

One Protocol - two memory options.

The protocol and command structure for HITAG S is based on HITAG 1, including

anticollision algorithm.

Two different memory sizes are offered and can be operated using exactly the same

protocol.

• HITAG S256 with 256 bit Total Memory Read/Write

• HITAG S2048 with 2048 bit Total Memory Read/Write

2. Features and benefits

2.1 Features

 Integrated Circuit for Contactless Identification Transponders and Cards

 Integrated resonance capacitor of 210 pF with 5 % tolerance over full production

 Frequency range 100 kHz to 150 kHz.

2.2 Protocol

 Modulation Read/Write Device  Transponder: 100 % ASK and Binary Pulse Length

Coding

 Modulation Transponder  Read/Write Device: Strong ASK modulation with

Anticollision, Manchester and Bi-phase Coding

 Fast Anticollision Protocol for inventory tracking: 100 Tags in 3.2 seconds

 Cyclic Redundancy Check (CRC)

 Optional Transponder Talks First Modes with user defined data length

 Temporary switch from Transponder Talks First into Reader Talks First Mode

HTSICH56; HTSICH48

HITAG S transponder IC

Rev. 3.1 — 11 December 2014

210331

Product short data sheet

COMPANY PUBLIC

Summary of content (21 pages)

PAGE 1
HTSICH56; HTSICH48 HITAG S transponder IC Rev. 3.1 — 11 December 2014 210331 Product short data sheet COMPANY PUBLIC 1. General description The HITAG product line is well known and established in the contactless identification market. Due to the open marketing strategy of NXP Semiconductors there are various manufacturers well established for both the transponders / cards as well as the Read/Write Devices. All of them supporting HITAG 1 and HITAG 2 transponder IC's.
PAGE 2
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC  Data Rate Read/Write Device to Transponder: 5.2 kBit/s  Data Rates Transponder to Read/Write Device: 2 kBit/s, 4 kBit/s, 8 kBit/s 2.3 Memory     Two memory options (256 bit, 2048 bit) Up to 100000 erase/write cycles 10 years non-volatile data retention Secure Memory Lock functionality 2.
PAGE 3
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 4. Quick reference data Table 1. Quick reference data Symbol Parameter Conditions Min Typ[1] Max Unit Tamb  55 C 10 - year Wafer EEPROM characteristics tret retention time Nendu(W) write endurance - 100000 cycle Interface characteristics input capacitance Ci between IN1 and IN2 [2] 199 210 221 pF HTSICxxxxxEW/x7 [1] Typical ratings are not guaranteed. Values are at 25 C. [2] Measured with Qcoil = 20, Lcoil = 7.
PAGE 4
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 6. Block diagram The HITAG S Transponder requires no external power supply. The contactless interface generates the power supply and the system clock via the resonant circuitry by inductive coupling to the Read/Write Device (RWD). The interface also demodulates data transmitted from the RWD to the HITAG S Transponder, and modulates the magnetic field for data transmission from the HITAG S Transponder to the RWD.
PAGE 5
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7. Functional description 7.1 Memory organization Page Address Block 0 Block 1 Block 2 Block 3 Block 15 HITAG S Type 32 bit 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E page 0 page 1 page 2 page 3 page 4 page 5 page 6 page 7 page 8 page 9 page 10 page 11 page 12 page 13 page 14 0x0F 0x10 page 15 page 16 0x3B 0x3C 0x3D 0x3E page 59 page 60 page 61 page 62 0x3F page 63 H56 H48 aaa-000830 Fig 2.
PAGE 6
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.2 HITAG S plain mode Table 3. Memory map for HITAG S in plain mode MSByte page address MSB LSByte LSB MSB LSB MSB UID2 LSB MSB UID1 LSB 0x00 UID3 UID0 0x01 Reserved CON2 CON1 CON0 0x02 Data 3 Data 2 Data 1 Data 0 0x03 Data 3 Data 2 Data 1 Data 0 7.3 HITAG S authentication mode Table 4.
PAGE 7
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.4 State Diagram 7.4.1 General Description of States Power Off The powering magnetic field is switched off or the HITAG S Transponder is out of field. Ready After start up phase, the HITAG S Transponder is ready to receive the first command. Init The HITAG S Transponder enters this State after the first UID REQUEST xx command. In this State the Response Protocol Mode (see Section 7.5) may be changed by further UID REQUEST xx commands.
PAGE 8
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.4.
PAGE 9
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.5 Command set 7.5.1 UID REQUEST xx Table 5. UID request xx LSByte MSB RWD: LSB UID REQUEST xx Transponder: MSB MSByte LSB MSB LSB MSB LSB MSB LSB EOF twresp SOF N= UID 0 UID 1 UID 2 UID 3 1............8 9.....k.......16 17............24 25............32 7.5.
PAGE 10
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.5.3 SELECT (UID) Table 7. Select (UID) LSByte MSB RWD: 00000 MSByte LSB MSB UID 0 LSB UID 1 MSB LSB UID 2 MSB LSB UID 3 MSB LSB CRC 8 EOF MSByte LSByte MSB Transponder: twresp SOF LSB CON 0 MSB LSB CON 1 MSB LSB CON 2 MSB LSB Reserved MSB LSB CRC 8 The complete response of the HITAG S Transponder is transmitted in Manchester Coding (MC).
PAGE 11
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.5.4 CHALLENGE By means of the response of the SELECT (UID) command the RWD detects that the HITAG S Transponder is configured in Authentication Mode (Bit AUT = 1) and starts the encrypted Challenge sequence. Table 8.
PAGE 12
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.5.5 SELECT_QUITE (UID) With this command a HITAG S Transponder in Init State can be directly entered into the quiet state. Table 9. Select_quiet(UID) LSByte MSByte MSB LSB MSB LSB MSB LSB MSB LSB RWD: 00000 UID 0 UID 1 UID 2 UID 3 MSB LSB 0 CRC 8 EOF ACK twresp SOF 0 1 Transponder: The Start Of Frame (SOF) pattern and the acknowledge (ACK) is transmitted in Manchester Coding. 7.5.
PAGE 13
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.5.7 READ BLOCK After transmitting the READ BLOCK command, the Page address PADR (8 Bits) within a block and the 8 bit Cyclic Redundancy Check (CRC 8), the HITAG S Transponder responds with the SOF and 32 up to 128 Bits of data beginning with the addressed Page within a Block to the last Page of the corresponding Block. Table 11.
PAGE 14
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.5.8 WRITE PAGE After a HITAG S Transponder was selected by the corresponding SELECT (UID) command (or SELECT (UID) and CHALLENGE for Authentication Mode) a write operation of data onto the memory can be carried out. Least significant Byte is always transmitted first. E.g. in order to change the configuration page the byte CON0 would have to be transmitted first.
PAGE 15
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.5.9 WRITE BLOCK After transmitting the WRITE BLOCK command, the Page address PADR (8 Bits) within a Block and the 8 bit Cyclic Redundancy Check (CRC 8), the HITAG S Transponder responds with the SOF and an acknowledge (ACK) to confirm the reception of a correct WRITE BLOCK command.
PAGE 16
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 7.5.10 QUITE With this command a Selected HITAG S Transponder can be entered into the Quiet State. A valid Page address PADR (8 Bits) and Cyclic Redundancy Check (CRC 8) must be sent for command structure reasons only. Table 19. Quiet MSB RWD: 0111 LSB MSB PADR CRC 8 LSB EOF ACK Transponder: HTSICH56_48_SDS Product short data sheet COMPANY PUBLIC twresp All information provided in this document is subject to legal disclaimers. Rev.
PAGE 17
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 8. Limiting values Table 20. Limiting values[1][2] In accordance with the Absolute Maximum Rating System (IEC 60134).
PAGE 18
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 10. Abbreviations Table 22. Abbreviations Acronym Description ASK Amplitude Shift Keying CRC Cyclic Redundancy Check EEPROM Electrically Erasable Programmable Read-Only Memory IC Integrated Circuit RF Radio Frequency RTF Reader Talks First RWD Read Write Device TTF Transponder Talks First UID Unique Identification Number 11. Revision history Table 23.
PAGE 19
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC 12. Legal information 12.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
PAGE 20
HTSICH56; HTSICH48 NXP Semiconductors HITAG S transponder IC Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding.
PAGE 21
NXP Semiconductors HTSICH56; HTSICH48 HITAG S transponder IC 14. Contents 1 2 2.1 2.2 2.3 2.4 2.5 2.6 3 4 5 6 7 7.1 7.2 7.3 7.4 7.4.1 7.4.2 7.5 7.5.1 7.5.2 7.5.3 7.5.4 7.5.5 7.5.6 7.5.7 7.5.8 7.5.9 7.5.10 8 9 10 11 12 12.1 12.2 12.3 12.4 13 14 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . .