User's Guide

ManualsBrandsNXP Laboratories UK ManualsElectronicsJN5168-Ã˜Ã˜1-MÃ˜Ã˜ IEEE802.15.4 Wireless Module

Data Sheet: JN5168-001-Myy

JenNet, ZigBee PRO and IEEE802.15.4 Module

JN-DS-JN5168-001-Myy © NXP Laboratories UK 2012

Features: Module

 2.4GHz IEEE 802.15.4, JenNet-IP,

ZigBee Light Link, ZigBee Smart Energy

and RF4CE compatible

 JN5168-001-M00/03

up to 1km range (Ext antenna)

M00: integral antenna 16x30mm

M03: uFl connector 16x21mm

o TX power +2.5dBm

o Receiver sensitivity –95dBm

o TX current 15mA

o RX current 17.5mA

o 2.0-3.6V operation

 JN5168-001-M05

up to 2km range (Ext 2dBi Antenna)

o 9.5 dBm TX Power

o Receiver sensitivity -96dBm

o uFl connector

o TX current 35mA

o RX current 22mA

o 16x30mm

o 2.0-3.6V operation

 JN5168-001-M06

up to 6km range (Ext 2 dBi Antenna)

o 22dBm TX Power

o Receiver sensitivity -100dBm

o uFl connector

o TX current 175mA

o RX current 22mA

o 16x30mm

o 2.0-3.6V operation

Features: Microcontroller

 32-bit RISC CPU, up to 32MIPs with low

power

 Data EEPROM with guaranteed 100k

write operations

 RF4CE, JenNet-IP, ZigBee Smart

Energy stacks

 JTAG debug interface

 4-input 10-bit ADC, 1 comparator

 5 x PWM (4 x timer, 1 x timer/counter)

 2 UARTs

 SPI Master & Slave port with 3 selects

 2-wire serial interface

 Battery and Temperature Sensor

 Watchdog timer and BOR

 Up to 20 DIO

Industrial temp (-40°C to +85°C)

Lead-free and RoHS compliant

Overview

The JN5168-001-Myy family is a range of ultra low power, high performance surface mount

modules targeted at IEEE 802.15.4, JenNet-IP, ZigBee Light Link, ZigBee Smart Energy and

RF4CE networking applications, enabling users to realise products with minimum time to

market and at the lowest cost. They remove the need for expensive and lengthy development

of custom RF board designs and test suites. The modules use NXP‟s JN5168 wireless

microcontroller to provide a comprehensive solution with large memory, high CPU and radio

performance and all RF components included. All that is required to develop and manufacture

wireless control or sensing products is to connect a power supply and peripherals such as

switches, actuators and sensors, considerably simplifying product development.

Four module variants are available: JN5168-001-M00 with an integrated antenna, JN5168-001-

M03 with an antenna connector and the JN5168-001-M05 and M06 with an antenna connector,

power amplifier and LNA for extended range. The JN5168-001-M05 output power has been

optimised for use in Europe and Asia.

Module Block Diagram

Benefits

 Microminiature module solutions

 Ready to use in products

 Minimises product development

time

 No RF test required for systems

 Compliant with

o FCC 47CFR Part 15C

o IC Canada RSS 210 Issue 8 -

Annex 8,

o ETSI EN 300-328 V1.7.1

o EN 301-489-17 V2.1.1

o EN60950-1-2006 +A1, A11, A12

Applications

 Robust and secure low power wireless

applications

 ZigBee and JenNet-IP networks

 Home and commercial building

automation

 Utilities metering (e.g. AMR)

 Location Aware services (e.g. Asset

Tracking)

 Toys and gaming peripherals

 Industrial systems

 Telemetry

 Remote Control

4xPWM + Timers

2x UART

4 Chan 10-bit ADC

Battery and Temp

Sensor

2-Wire Serial

(Master/Slave)

SPI Master & Slave

RAM

8/32K

128-bit AES

Encryption

Accelerator

2.4GHz

Radio

Including

Diversity

Flash

64/160/256K

32 -Bit

RISC CPU

Power

Management

XTAL

O-QPSK

Modem

IEEE802.15.4

MAC

Accelerator

Power

Matching

uFl

Connector

Matching

Integrated Antenna

Matching

uFl

Connector

PA / LNA

External

Antenna

M00 Option

M03 Option

M05/M06 Option

20 DIO

Sleep Counter

4kB

EEPROM

Watchdog

Timer

Voltage

Brownout

Summary of content (25 pages)

PAGE 1
Data Sheet: JN5168-001-Myy JenNet, ZigBee PRO and IEEE802.15.4 Module Overview The JN5168-001-Myy family is a range of ultra low power, high performance surface mount modules targeted at IEEE 802.15.4, JenNet-IP, ZigBee Light Link, ZigBee Smart Energy and RF4CE networking applications, enabling users to realise products with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites.
PAGE 2
Contents 1. Introduction 3 1.1. 1.2. 3 3 Variants Regulatory Approvals 2. Specifications 4 2.1. 5 JN5168 Single Chip Wireless Microcontroller 3. Pin Configurations 6 3.1. 3.2. 3.2.1 7 8 8 Pin Assignment Pin Descriptions Power Supplies 4. Electrical Characteristics 9 4.1. 4.2. 9 9 Maximum Ratings Operating Conditions Appendix A Additional Information 10 A.1 A.2 A.3 A.4 A.5 A.5.1 A.5.2 A.6 A.7 A.8 A.8.1 A.8.2 A.8.3 A.9 A.9.1 A.10 A.11 A.12 A.
PAGE 3
1. Introduction The JN5168-001-Myy module family provides designers with a ready-made component that provides a fully integrated solution for applications, using the IEEE802.15.4 standard in the 2.4-2.5GHz ISM frequency band [1], including JenNet-IP and ZigBee Smart Energy, and can be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test.
PAGE 4
2. Specifications Most specification parameters for the modules are specified in the chip datasheet - JN-DS-JN5168 Wireless Microcontroller Datasheet [2]. Where there are differences, the parameters are defined here. VDD=3.0V @ +25°C Typical DC Characteristics Notes JN5168-001M00/03 JN5168-001M06 JN5168-001M05 Deep sleep current 100nA 100nA 100nA Sleep current 0.70uA 0.70uA 0.
PAGE 5
SPI selects) Four channel Analogue-to-Digital converter    10-bit, up to 100ks/s Programmable analogue comparators    Ultra low power mode for sleep Internal temperature sensor and battery monitor    The performance of all peripherals is defined in the JN-DS-JN5168 Wireless Microcontroller Datasheet [2]. Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated antenna have approximately 1.5 dB less e.i.r.
PAGE 6
3. Pin Configurations ADC1 SPICLK SPIMISO SPIMISI 1 27 2 26 3 25 4 24 SPISSZ DIO0 DIO1 5 23 DIO2 DIO3 6 22 7 21 8 20 9 19 ADC2 DIO17 DIO16 DIO15 DIO14 RESETN DIO13 DIO12 DIO11 GND DIO10 VDD DIO4 DIO5 DIO6 DIO7 DIO8 DIO9 10 11 12 13 14 15 16 17 18 Figure 1: Pin Configuration (top view) Note that the same basic pin configuration applies for all module designs. However, DIO3 (pin 9) and DIO2 (pin 8) are not available on the JN5168-001-M05 and JN5168-001-M06.
PAGE 7
3.1. Pin Assignment Pin No Pin Functions Primary Signal Type Alternate Functions 1 ADC1 2 SPICLK 3.
PAGE 8
SPISSEL 24 DIO15 SIF_D RXD0 RXD1 JTAG_TDI 25 DIO16 COMP1P SIF_CLK SPISMOSI 26 DIO17 COMP1M PWM4 I2C DATA 27 ADC2 SPISEL2 SPISIMO UART 0 Transmit Data Output, UART 1 Transmit Data Output, JTAG Data Output, SPI Master Select Output 1 or SPI Slave Select Input CMOS DIO15, Serial Interface Data or Intelligent Peripheral Data Out CMOS DIO16, Comparator Positive Input, Serial Interface clock or SPI Slave Master Out Slave In Input DIO17, Comparator Negative Input, Serial Interface Data or SP
PAGE 9
4. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. 4.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Min Max Device supply voltage VDD -0.3V 3.6V All Pins -0.3V VDD + 0.3V Storage temperature -40ºC 150ºC 4.2. Operating Conditions Supply Min Max VDD 2.0V 3.
PAGE 10
Appendix A Additional Information A.1 Outline Drawing 16mm 30.0mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.
PAGE 11
16mm 9.76mm 2.56 mm 1.27 mm 21mm 2.54 mm 2.54 mm 3.30 mm Thickness: 3.
PAGE 12
16mm 8.0mm 2.90mm 30mm 1.27 mm 2.54 mm . 2.54 mm 3.30 mm Thickness: 3.
PAGE 13
A.2 Module PCB Footprint All dimensions are in mm. 14.88 1.27 Ø1 2.23 1.5 2.23 2.
PAGE 14
A.3 Optimal PCB placement of the JN5168-001-M00 Module The JN5168-001-M00 module features an optimised, low cost, integrated, inverted F, printed PCB antenna. The antenna has a vertically polarised near omnidirectional radiation pattern and up to 1.6 dBi of peak gain. The PCB design has been elongated in order to increase the ground plane area which increases the antenna efficiency.
PAGE 15
A.4 JN5168-001-M00 Antenna Radiation Pattern Figure 7, Figure 8 &Figure 9 are simulated 3D radiation plots of the JN5168-001-M00. They are provided here to help the user orientate the module in end equipment in an optimal way. These visualisations are an accurate representation of the antenna radiation pattern in the 3D space.
PAGE 16
Figure 7: 3D radiation plot JN5168-001-M00 XY Orientation (simulation) Figure 8: 3D radiation plot JN5168-001-M00 XZ Orientation (simulation) 16 JN-DS-JN5168-001-Myy 1v1 © NXP Laboratories UK 2012
PAGE 17
Figure 9: 3D radiation plot JN5168-001-M00 YZ Orientation (simulation) © NXP Laboratories UK 2012 JN-DS-JN5168-001-Myy 1v1 17
PAGE 18
JN5168-001-M00 Radiation Plots @ 3 meters (XZ Orientation) CH11 CH18 CH26 dBuV 104 94 84 74 64 54 44 34 24 14 4 14 24 34 44 54 64 74 84 94 104 Mkr Trace 2 3 X-Axis Value 1 CH11 40.0 deg 101.04 dBuV 2 CH18 40.0 deg 100.67 dBuV 3 CH26 40.0 deg 101.
PAGE 19
dBuV/m @ 3m Module Peak Field Strengths 104.0 103.5 103.0 102.5 102.0 101.5 101.0 100.5 100.0 99.5 99.0 98.5 98.0 JN5168-001-M03 with vertical JN5168-001-M00 JN5148-001-M00 11 18 26 Channel Figure 11: Peak Field Strengths for various modules optimised for height and azimuth A.5 Manufacturing A.5.
PAGE 20
A.5.2 Soldering Paste and Cleaning NXP does not recommend use of a solder paste that requires the module and PCB assembly to be cleaned (rinsed in water) for the following reasons: Solder flux residues and water can be trapped by the PCB, can or components and result in short circuits. The module label could be damaged or removed. NXP recommends use of a 'no clean' solder paste for all its module products. A.
PAGE 21
A.7 Related Documents [1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology – Part 15.4 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) [2] JN-DS-JN5168 Wireless Microcontroller Datasheet A.8 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 22
A.8.1 Antennas approved by FCC for use with JN5168 modules Brand Model Number Description Gain (dBi) Connector type 1 Antenna Factor ANT-2.4-CW-RCT-RP Vertical - knuckle antenna 2.2 RP-SMA 2 Antennova 2010B6090-01 Vertical - knuckle antenna 2.2 RP-SMA 3 Hyperlink Technology HG2402RD-RSF Vertical - knuckle antenna 2.
PAGE 23
A.9 Industry Canada Statement This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 24
A.11 RoHS Compliance JN5168-001-Myy devices meet the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). The JN5168-001-M00, M03, M05 and M06 modules meet the requirements of Chinese RoHS requirements SJ/T11363-2006. Full data can be found at www.nxp.com/jennic. A.12 Status Information The status of this Data Sheet is Preliminary.
PAGE 25
Version Control Version Notes 1.0 Initial release 1.1 Additional clarification of RF exposure conditions added to FCC section A8 NXP Laboratories UK Ltd Furnival Street Sheffield S1 4QT United Kingdom Tel: +44 (0)114 281 2655 Fax: +44 (0) 114 281 2951 For the contact details of your local NXP office or distributor, refer to the NXP web site: www.nxp.