User Manual

ManualsBrandsNXP Laboratories UK ManualsElectronicsJN5148-001-M06 IEEE802.15.4 Wireless Module

Table Of Contents

Data Sheet: JN5148-001-Myy

JenNet, ZigBee PRO and IEEE802.15.4 Module

JN-DS-JN5148-001-Myy 1v5 © NXP Laboratories UK 2012

Features: Module

• 2.4GHz IEEE802.15.4, JenNet and

ZigBee PRO compatible

•

JN5148-001-M00/03

up to 1km range (Ext antenna)

M00: integral antenna 18x32mm

M03: uFl connector 18x30mm

o TX power +2.5dBm

o Receiver sensitivity –95dBm

o TX current 15mA

o RX current 17.5mA

o 2.3-3.6V operation

• JN5148-001-M06

up to 4km range (Ext Antenna)

o 22dBm TX Power

o 18dBm TX power (M04

compatible)

o Receiver sensitivity -100dBm

o uFl connector

o TX current 84mA

o RX current 23mA

o 18x41mm

o 2.3-3.6V operation

Features: Microcontroller

• 32-bit RISC CPU, up to 32MIPs with

low power

• 128kB ROM stores system code

• 128kB RAM stores system data and

bootloaded program code

• 4Mbit serial flash for program code

and data

• On chip OTP efuse

• JTAG debug interface

• 4-input 12-bit ADC, 2 12-bit DACs, 2

comparators

• 3 application timer/counters,

• 2 UARTs

• SPI port with 5 selects

• 2-wire serial interface

• 4-wire digital audio interface

• Watchdog timer

• Up to 21 DIO

Industrial temp (-40°C to +85°C)

Lead-free and RoHS compliant

Overview

The JN5148-001-Myy family is a range of ultra low power, high performance surface

mount modules targeted at JenNet and ZigBee PRO networking applications,

enabling users to realise products with minimum time to market and at the lowest

cost. They remove the need for expensive and lengthy development of custom RF

board designs and test suites. The modules use NXP’s JN5148 wireless

microcontroller to provide a comprehensive solution with large memory, high CPU

and radio performance and all RF components included. All that is required to

develop and manufacture wireless control or sensing products is to connect a power

supply and peripherals such as switches, actuators and sensors, considerably

simplifying product development.

Three module variants are available: JN5148-001-M00 with an integrated antenna,

JN5148-001-M03 with an antenna connector and the JN5148-001-M06 with an

antenna connector, power amplifier and LNA for extended range. The modules can

implement networking stacks such as JenNet and ZigBee PRO, as well as customer

applications

Module Block Diagram

Benefits

• Microminiature module solutions

• Ready to use in products

• Minimises product development

time

• No RF test required for systems

• Compliant with FCC part 15

rules, IC Canada RSS 210e,

ETSI EN 300-328

Applications

• Robust and secure low power

wireless applications

• ZigBee PRO and JenNet

networks

• Home and commercial building

automation

• Utilities metering (e.g. AMR)

• Location Aware services (e.g.

Asset Tracking)

• Toys and gaming peripherals

• Industrial systems

• Telemetry

• Remote Control

Timers

UARTs

12-bit ADC,

comparators

12-bit DACs,

temp sensor

2-wire serial

SPI

RAM

128kB

128-bit AES

Encryption

Accelerator

2.4GHz

Radio

ROM

128kB

RISC CPU

Power

Management

XTAL

O-QPSK

Modem

IEEE802.15.4

MAC

Accelerator

512kB Serial

Flash Memory

JN5148 chip

Power

Matching

uFl

Connector

Matching

Integrated Antenna

Matching

uFl

Connector

PA / LNA

External

Antenna

M00 Option

M03 Option

M06 Option

4-Wire Audio

Sleep Counters

32-byte

OTP eFuse

Watchdog timer

Time of Flight

Engine

Summary of content (23 pages)

PAGE 1
Data Sheet: JN5148-001-Myy JenNet, ZigBee PRO and IEEE802.15.4 Module Overview The JN5148-001-Myy family is a range of ultra low power, high performance surface mount modules targeted at JenNet and ZigBee PRO networking applications, enabling users to realise products with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites.
PAGE 2
Contents 1. Introduction 3 1.1. 1.2. 3 3 Variants Regulatory Approvals 2. Specifications 4 3. Product Development 6 3.1. 6 JN5148 Single Chip Wireless Microcontroller 4. Pin Configurations 7 4.1. 4.2. 4.2.1 4.2.2 8 9 9 9 Pin Assignment Pin Descriptions Power Supplies SPI Memory Connections 5. Electrical Characteristics 10 5.1. Maximum Ratings 5.2. Operating Conditions Appendix A Additional Information A.1 Outline Drawing A.2 Module PCB Footprint A.3 Manufacturing A.3.1 Reflow Profile A.3.
PAGE 3
1. Introduction The JN5148-001-Myy module family provides designers with a ready made component that provides a fully integrated solution for applications, using the IEEE802.15.4 standard in the 2.4-2.5GHz ISM frequency band [1], including JenNet and ZigBee PRO, and can be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test.
PAGE 4
2. Specifications Most specification parameters for the modules are specified in the chip datasheet - JN-DS-JN5148 Wireless Microcontroller Datasheet, [2]. Where there are differences, the parameters are defined here. VDD=3.0V @ +25°C Typical DC Characteristics Notes JN5148-001M00/03 JN5148-001M06 Deep sleep current 1.3uA 120nA Sleep current 2.6uA 1.
PAGE 5
Two programmable analogue comparators   Internal temperature sensor and battery monitor   Ultra low power mode for sleep The performance of all peripherals is defined in the JN-DS-JN5148 Wireless Microcontroller Datasheet [2] Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated antenna have approximately 4 dB less e.i.r.p and reciprocal receive sensitivity.
PAGE 6
3. Product Development NXP supplies all the development tools and networking stacks needed to enable end-product development to occur quickly and efficiently. These are all freely available from www.nxp.com/jennic. A range of evaluation/developer kits is also available, allowing products to be quickly bread boarded. Efficient development of software applications is enabled by the provision of a complete, unlimited, software developer kit. Together with the available libraries for the IEEE802.15.
PAGE 7
4.
PAGE 8
4.1. Pin Assignment Pin No Pin Functions Primary Alternate Functions Signal Type Description 1 ADC4 3.3V 2 DAC1 3.3V Analogue to Digital Input DAC Output 3 DAC2 3.3V DAC Output 4 COMP2+ 3.3V Comparator 2 Input +ve 5 COMP2- 3.
PAGE 9
33 DIO17 CTS1 IP_SEL DAI_SCK JTAG_TCK CMOS DIO17, UART 1 Clear To Send Input, Intelligent Peripheral Device Select Input or Digital Audio Clock or JTAG CLK 34 DIO18 RTS1 IP_INT DAI_SDOUT JTAG_TMS CMOS DIO18, UART 1 Request To Send Output, Intelligent Peripheral Interrupt Output or Digital Audio Data Output or JTAG Mode Select 35 DIO19 TXD1 JTAG_TDO CMOS DIO19 or UART 1 Transmit Data Output or JTAG Data Out 36 DIO 20 RXD1 JTAG_TDI CMOS DIO 20, UART 1 Receive Data Input or JTAG data
PAGE 10
5. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. 5.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Min Max Device supply voltage VDD -0.3V 3.6V Voltage on analogue pins VREF, ADC1-4, DAC1-2, COMP1M, COMP1P, COMP2M, COMP2P, IBIAS -0.3V VDD + 0.
PAGE 11
Appendix A Additional Information A.1 Outline Drawing 18mm 32.2mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.
PAGE 12
18mm 9.76mm 6.58 mm 30mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.
PAGE 13
18mm 7.2mm 4.05mm 40.5mm 1.27 mm 2.54 mm . 2.54 mm 2.76 mm Thickness: 3.
PAGE 14
A.2 Module PCB Footprint All dimensions are in mm. 17.42 * * 1.27 Ø1 2.23 1.5 2.23 2.49 1 Note: All modules have the same footprint except for the M06 which has 2 additional pins marked with a * Figure 5 Module PCB footprint RF note for –M00 modules with integral antenna: No components, ground plane or tracks on any layer of the mother board should be placed within 20mm of the 3 free sides of the antenna.
PAGE 15
A.3 Manufacturing A.3.1 Reflow Profile For reflow soldering, it is recommended to follow the reflow profile in figure 6 as a guide, as well as the paste manufacturers guidelines on peak flow temperature, soak times, time above liquidus and ramp rates. Temperature Target Time (s) 25~160 ºC 160~190 ºC > 220º C 230~Pk. Pk. Temp (235ºC) 90~130 30~60 20~50 10~15 150~270 Figure 6: Recommended solder reflow profile A.3.
PAGE 16
A.4 Ordering Information Ordering Code Format: JN5148 - 001 – M / Y1Y2 Y3 Shipping T Tape Mounted 500-piece reel Module Type 00 Standard Power, Integral antenna 03 Standard Power, uFl connector 06 High power, uFl connector Where this Data Sheet is denoted as “Advanced” or “Preliminary”, devices will be either Engineering Samples or Prototypes. Devices of this status have an Rx suffix after the module type to identify qualification status during these product phases - for example, JN5148-001-M00R1T.
PAGE 17
A.5 Tape and Reel Information: A.5.1 Tape Orientation and dimensions All dimensions are in mm Module type: A B W F E P0 P1 P2 T Cover Tape width (W) JN5148-001-M00 18.4 32.6 44 20.2 1.75 4.0 2.0 24.0 3.4 37.5 JN5148-001-M03 18.4 30.4 44 20.2 1.75 4.0 2.0 24.0 3.4 37.5 JN5148-001-M06 18.5 40.9 56 26.2 1.75 4.0 2.0 24.0 3.4 49.5 Tolerance ±0.1 ±0.1 ±0.3 ±0.1 +0.1 ±0.1 ±0.1 ±0.1 ±0.1 ±0.1 A.5.2 Cover tape details Thickness (T) 0.
PAGE 18
A.5.3 Leader and Trailer 300 MM 300 MM A.5.4 Reel Dimensions: All dimensions are in mm. Module type: A B C N W (min) JN5148-xxx-M00/03 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 44.5 ±0.3 JN5148-xxx-M06 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 56.5 ±0.3 A.6 Related Documents [1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology – Part 15.
PAGE 19
A.7 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 20
A.7.1 Antennas approved by FCC for use with JN5148 modules Brand Model Number Description Gain (dBi) Connector type 1 Antenna Factor ANT-2.4-CW-RCT-RP Vertical - knuckle antenna 2.2 RP-SMA 2 Antennova 2010B6090-01 Vertical - knuckle antenna 2.2 RP-SMA 3 Hyperlink Technology HG2402RD-RSF Vertical - knuckle antenna 2.
PAGE 21
A.8 Industry Canada Statement To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. These modules have been designed to operate with antennas having a maximum gain of 2.2 dBi. Antennas having a gain greater than 2.2 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
PAGE 22
A.10 RoHS Compliance JN5148-001-Myy devices meet the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). The JN5148-001-M00, M03 and M06 modules meet the requirements of Chinese RoHS requirements SJ/T113632006. Full data can be found at www.nxp.com/jennic. A.11 Status Information The status of this Data Sheet is Production.
PAGE 23
Version Control Version Notes 1.0 1st Issue of Advanced Datasheet 1.1 1st Issue of Preliminary Datasheet, minor parametric changes and addition of Appendix A6.3 1.2 1st Issue of Production Datasheet, addition of PCB cleaning information in Appendix A3 1.3 Logo updated and support of JenNet added 1.4 Ordering information changed 1.