User Manual

ManualsBrandsNXP Laboratories UK ManualsElectronicsJN5142-001-M03 IEEE802.15.4 Wireless Module

Data Sheet: JN5142-x01-Myy

JenNet-IP,RF4CE and IEEE802.15.4 Module

JN-DS-JN5142-x01-Myy 1v0 © NXP Laboratories UK 2012

Features: Module

 2.4GHz IEEE802.15.4, JenNet-IP

and RF4CE compatible

 Sleep current (with active sleep

timer) 0.73µA

 JN5142-x01-M00/03

up to 1km range (Ext antenna)

M00: integral antenna 18x32mm

M03: uFl connector 18x30mm

o TX power +2.5dBm

o Receiver sensitivity –95dBm

o TX current 15mA

o RX current 17.5mA

o 2.3-3.6V operation

Features: Microcontroller

 32-bit RISC CPU, 1-32MHz clock

speed

 Low power operation

 Variable instruction width for high

coding efficiency

 Multi-stage instruction pipeline

 128KB ROM and 32KB RAM for

bootloaded program code

 Master/Slave I2C interface.

 3xPWM and Application

timer/counter

 UART

 SPI port with 3 selects

 Supply Voltage Monitor with 8

programmable thresholds

 4-input 8-bit ADC

 Comparator

 Battery and temperature sensors

 Watchdog timer and Power-on-

Reset (with brown-out) circuit

 Up to 18 DIO

Industrial temp (-40°C to +125°C)

6x6mm 40-lead Punched QFN

Lead-free and RoHS compliant

Overview

The JN5142-x01-Myy family is a range of ultra low power, high performance surface

mount modules targeted at JenNet-IP and RF4CE networking applications, enabling

users to realise products with minimum time to market and at the lowest cost. They

remove the need for expensive and lengthy development of custom RF board

designs and test suites. The modules use NXP‟s JN5142 wireless microcontroller to

provide a comprehensive solution with large memory, high CPU and radio

performance and all RF components included. All that is required to develop and

manufacture wireless control or sensing products is to connect a power supply and

peripherals such as switches, actuators and sensors, considerably simplifying

product development.

Two module variants are available: JN5142-x01-M00 with an integrated antenna and

the JN5142-x01-M03 with antenna connector. The modules can implement

networking stacks such as JenNet-IP and RF4CE, as well as customer applications.

Module Block Diagram

128kB Serial Flash

Memory

Power

Matching

uFl

Connector

Integrated

Antenna

External

Antenna

M00 Option

M03 Option

32-bit

RISC CPU

Timer

UART

4-Chan 8-bit ADC

Battery &

Temp sensors

2-Wire Serial

(Master)

SPI

128-bit AES

Encryption

Accelerator

2.4GHz

Radio

2.4GHz

Radio

ROM

128KB

Power

Management

XTAL

QPSK

Modem

29-byte

OTP eFuse

2-Wire Serial

(Slave)

Sleep Counter

Watchdog

Timer

Watchdog

Timer

Voltage Supply

Monitor

RAM

32KB

IEEE802.15.4

MAC

Accelerator

Matching

Benefits

 Single chip optimized for simple

applications

 Very low current solution for

long battery life – over 10 yrs

 Highly featured 32-bit RISC

CPU for high performance and

low power

 System BOM is low in

component count and cost

 FCC part 15.247 rules, IC

Canada RSS 210e and ETSI EN

300-328 v 1.7 compliant

Applications

 Robust and secure low power

wireless applications using

RF4CE

 Remote Control

 Toys and gaming peripherals

 Active RFID tags

 Point-to-point or star networks

using IEEE802.15.4

 Energy harvesting, for example

self powered light switch

Summary of content (20 pages)

PAGE 1
Data Sheet: JN5142-x01-Myy JenNet-IP,RF4CE and IEEE802.15.4 Module Overview The JN5142-x01-Myy family is a range of ultra low power, high performance surface mount modules targeted at JenNet-IP and RF4CE networking applications, enabling users to realise products with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites.
PAGE 2
Contents 1. Introduction 3 1.1. 1.2. 3 3 Variants Regulatory Approvals 2. Specifications 4 3. Product Development 5 3.1. 5 JN5142 Single Chip Wireless Microcontroller 4. Pin Configurations 6 4.1. 4.2. 4.2.1 4.2.2 7 8 8 8 Pin Assignment Pin Descriptions Power Supplies SPI Memory Connections 5. Electrical Characteristics 5.1. Maximum Ratings 5.2. Operating Conditions Appendix A Additional Information A.1 Outline Drawing A.2 Module PCB Footprint A.3 Manufacturing A.3.1 Reflow Profile A.3.
PAGE 3
1. Introduction The JN5142-x01-Myy module family provides designers with a ready-made component that provides a fully integrated solution for applications using the IEEE802.15.4 standard in the 2.4 - 2.5GHz ISM frequency band [1], including RF4CE. A later version of the JN5142 will provide support for JenNet-IP “Smart Device” applications such as lighting. Applications that transfer data wirelessly tend to be more complex than wired ones.
PAGE 4
2. Specifications Most specification parameters for the modules are specified in the chip datasheet - JN-DS-JN5142 Wireless Microcontroller Datasheet, [2]. Where there are differences, the parameters are defined here. VDD=3.0V @ +25°C Typical DC Characteristics Notes JN5142-x01M00/03 Deep sleep current 100nA Sleep current 0.73uA With active sleep timer Radio transmit current 14.8mA CPU in doze, radio transmitting Radio receive current 16.
PAGE 5
3. Product Development NXP supplies all the development tools and networking stacks needed to enable end-product development to occur quickly and efficiently. These are all freely available from www.nxp.com/jennic. A range of evaluation/developer kits is also available, allowing products to be quickly bread boarded. Efficient development of software applications is enabled by the provision of a complete, unlimited, software developer kit. Together with the available libraries for the IEEE802.15.
PAGE 6
4. Pin Configurations ADC1 NC 1 41 2 40 NC NC NC SPICLK SPIMISO SPIMOSI SPISSZ DIO0 3 39 4 38 5 37 6 36 7 35 8 34 DIO1 DIO2 SPISSM SPISWP DIO3 9 33 10 32 11 31 12 30 13 29 14 28 15 27 NC ADC2 NC NC NC NC NC NC DIO17 DIO16 DIO15 DIO14 RESETN DIO13 DIO12 VDD GND VSSA DIO10 DIO11 DIO4 DIO5 DIO6 DIO7 DIO8 DIO9 16 17 18 19 20 21 22 23 24 25 26 Figure 1: Pin Configuration (top view) Note that the same basic pin configuration applies for all module designs.
PAGE 7
Pin Assignment Pin No Pin Functions Primary 1 ADC1 2 NC 3 NC 4 NC Signal Type Alternate Functions 3.
PAGE 8
30 DIO14 SIF_CLK TXD0 JTAG_TDO SPISEL1 CMOS DIO14, Serial Interface Clock, UART 0 Transmit Data Output, JTAG Data Output or SPI Slave Select Output 1 31 DIO15 SIF_D RXD0 JTAG_TDI SPISEL2 CMOS DIO15, Serial Interface Data, UART 0 Receive Data Input, JTAG Data Input or SPI Slave Select Output 2 32 DIO16 COMP1P SIF_CLK CMOS DIO16, Comparator Positive Input or Serial Interface clock 33 DIO17 COMP1M SIF_D CMOS DIO17, Comparator Negative Input or Serial Interface Data 34 NC 35 NC 3
PAGE 9
5. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. 5.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Min Max Device supply voltage VDD -0.3V 3.6V Voltage on analogue pins ADC1-2 -0.3V VDD + 0.3V Voltage on 5v tolerant digital pins DIO0-DIO8 & DIO11-17, RESETN -0.
PAGE 10
Appendix A Additional Information A.1 Outline Drawing 18mm 32.2mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.
PAGE 11
18mm 9.76mm 6.58 mm 30mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.
PAGE 12
A.2 Module PCB Footprint All dimensions are in mm. Note: All modules have the same footprint. Figure 4 Module PCB footprint RF note for –M00 modules with integral antenna: No components, ground plane or tracks on any layer of the mother board should be placed within 20mm of the 3 free sides of the antenna. Tracks etc may be placed adjacent to the can, but should not extend past the can towards the antenna end of the module for 20mm from the antenna.
PAGE 13
A.3 Manufacturing A.3.1 Reflow Profile For reflow soldering, it is recommended to follow the reflow profile in figure 6 as a guide, as well as the paste manufacturers guidelines on peak flow temperature, soak times, time above liquidus and ramp rates. Temperature Target Time (s) 25~160 ºC 160~190 ºC > 220º C 230~Pk. Pk. Temp (235ºC) 90~130 30~60 20~50 10~15 150~270 Figure 5: Recommended solder reflow profile A.3.
PAGE 14
A.4 Ordering Information Ordering Code Format: JN5142 - x01 – M / Y1Y2 Y3 Shipping T Tape Mounted 500-piece reel Module Type 00 Standard Power, Integral antenna 03 Standard Power, uFl connector Where this Data Sheet is denoted as “Advanced” or “Preliminary”, devices will be either Engineering Samples or Prototypes. Devices of this status have an Rx suffix after the module type to identify qualification status during these product phases - for example, JN5142-X01-M00R1T.
PAGE 15
A.5 Tape and Reel Information: A.5.1 Tape Orientation and dimensions All dimensions are in mm Module type: A B W F E P0 P1 P2 T Cover Tape width (W) JN5142-x01-M00 18.4 32.6 44 20.2 1.75 4.0 2.0 24.0 3.4 37.5 JN5142-x01-M03 18.4 30.4 44 20.2 1.75 4.0 2.0 24.0 3.4 37.5 Tolerance ±0.1 ±0.1 ±0.3 ±0.1 +0.1 ±0.1 ±0.1 ±0.1 ±0.1 ±0.1 A.5.2 Cover tape details Thickness (T) 0.
PAGE 16
A.5.3 Leader and Trailer 300 MM 300 MM A.5.4 Reel Dimensions: All dimensions are in mm. Module type: A B C N W (min) JN5142-x01-M00/03 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 44.5 ±0.3 A.6 Related Documents [1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology – Part 15.
PAGE 17
A.7 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 18
A.7.1 Antennas approved by FCC for use with JN5142 modules Brand Model Number Description Gain (dBi) Connector type 1 Antenna Factor ANT-2.4-CW-RCT-RP Vertical - knuckle antenna 2.2 RP-SMA 2 Antennova 2010B6090-01 Vertical - knuckle antenna 2.2 RP-SMA 3 Hyperlink Technology HG2402RD-RSF Vertical - knuckle antenna 2.
PAGE 19
A.9 European R & TTE Directive 1999/5/EC Statement All modules listed in this datasheet are compliant with ETSI EN 300 328V1.7.1 (2006/05) and are subject to a Notified Body Opinion. The modules are approved for use with the antennas listed in the following table. 1 Brand Model Number Description Gain (dBi) Connector type Antenna Factor ANT-2.4-CW-RCT-RP Vertical - knuckle antenna 2.2 RP-SMA 2 Antennova 2010B6090-01 Vertical - knuckle antenna 2.
PAGE 20
Preliminary The Data Sheet shows the specification of a product that is commercially available, but is not yet fully qualified. The functionality of the product is final. The electrical performance specifications are target values and may be used as a guide to the final specification. Modules are identified with an Rx suffix, for example JN5142-x01-M00R2. NXP reserves the right to make changes to the product specification at anytime without notice.