Data Sheet

ManualsBrandsNXP Laboratories UK ManualsAudio EquipmentIEEE 802.15.4 Wireless Microcontroller

Data Sheet – JN5139-xxx-Myy

IEEE802.15.4/ZigBee Module Family

JN-DS-JN5139-xxx-Myy 1v5 © Jennic 2009

Features: Module

x 2.4GHz IEEE802.15.4 & ZigBee

compatible

x 2.7-3.6V operation

x Sleep current (with active sleep

timer) 2.6µA

x JN5139-xxx-M00/01/03

up to 1km range (ext antenna)

M00: on board antenna

M01: SMA connector

M03: uFl connector

o Receiver sensitivity –96dBm

o TX power +2.5dBm

o TX current 37mA

o RX current 37mA

o 18x30mm

x JN5139-xxx-M02/04

up to 4km range

M02: SMA connector

M04: uFl connector

o Receiver sensitivity -100dBm

o 19dBm TX power

o TX current 125mA

o RX current 45mA

o 18x41mm

Features: Microcontroller

x 16MHz 32-bit RISC CPU

x 96kB RAM, 192kB ROM

x 4-input 12-bit ADC, 2 11-bit

DACs, 2 comparators,

temperature sensor

x 2 Application timer/counters,

3 system timers

x 2 UARTs (one for in-system

debug)

x SPI port with 5 selects

x 2-wire serial interface

x 21 GPIO

x Evaluation kits available with full,

unlimited, Software Development

Kit

Temperature range

-20°C to +70°C

Lead-free and RoHS compliant

Overview

The JN5139-xxx-Myy family is a range of surface mount modules that enable users to

implement systems using IEEE802.15.4, 6LoWPAN, JenNet or ZigBee with minimum

time to market and at the lowest cost. They remove the need for expensive and

lengthy development of custom RF board designs and test suites. The modules use

Jennic’s JN5139 wireless microcontroller to provide a comprehensive solution with

high radio performance and all RF components included. All that is required to

develop and manufacture wireless control or sensing products is to connect a power

supply and peripherals such as switches, actuators and sensors, considerably

simplifying product development.

Three basic hardware module variants are available: JN5139-xxx-M00 with an

integrated antenna, JN5139-xxx-M01/M03 with an antenna connector and JN5139-

xxx-M02/M04 with a power amplifier and LNA for extended range. Variants are

available either with a ZigBee network stack (JN5139-Z01-Myy) or supporting the

other stacks (JN5139-001-Myy).

Module Block Diagram

Benefits

x Microminiature module solutions

x Ready to use in products

x Minimises product development

time

x No RF test required for systems

x Compliant with FCC part 15

rules, IC Canada, ETSI ETS

300-328 and Japan ARIB STD-

T66

x Production volumes supplied

pre-programmed with

application software

Applications

x Robust and secure low power

wireless applications

x Wireless sensor networks,

particularly IEEE802.15.4 /

ZigBee systems

x Home and commercial building

automation

x Home networks

x Toys and gaming peripherals

x Industrial systems

x Telemetry and utilities

(e.g. AMR)

Ti mers

UARTs

12-bit ADC,

comparat ors

11- bi t DACs,

temp sensor

2-wire seri al

SPI

RAM

96kB

128-bit AES

Encr ypti on

Ac ce l e r a t o r

2.4GHz

Radi o

ROM

192kB

RI SC CPU

Power

Management

XTAL

O-QPSK

Modem

IEEE802.15. 4

MAC

Acc e l e r a t or

128kB Serial

Flash Memory

JN5139 chip

Power

Bal un

Connector

Bal un

Ceramic Antenna

Bal unConnector PA / LNA

Ext er nal

Antenna

M00 Opt ion

M01/03 Option

M02/04 Option

Summary of content (27 pages)

PAGE 1
Data Sheet – JN5139-xxx-Myy IEEE802.15.4/ZigBee Module Family Features: Module Overview The JN5139-xxx-Myy family is a range of surface mount modules that enable users to implement systems using IEEE802.15.4, 6LoWPAN, JenNet or ZigBee with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites.
PAGE 2
Jennic Contents 1. Introduction 3 1.1. 1.2. 3 3 Variants Regulatory Approvals 2. Specifications 4 3. Product Development 6 3.1. 6 JN5139 Single Chip Wireless Microcontroller 4. Pin Configurations 7 4.1. 4.2. 4.2.1 4.2.2 8 9 9 9 Pin Assignment Pin Descriptions Power Supplies SPI Memory Connections 5. Electrical Characteristics 10 5.1. 5.2. 5.3. 10 10 11 Maximum Ratings Reflow Profile Operating Conditions Appendix A Additional Information A.1 Outline Drawing A.2 Module PCB Footprint A.
PAGE 3
Jennic 1. Introduction The JN5139-xxx-Myy module family provides designers with a ready made component which allows IEEE802.15.4 [1] wireless applications, using Jennic’s JenNet networking protocol or ZigBee, to be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins.
PAGE 4
Jennic 2. Specifications Most specification parameters for the modules are specified in the chip datasheet - JN-DS- JN513x Wireless Microcontroller Datasheet, [2]. Where there are differences, the parameters are defined here. VDD=3.0V @ +25°C Typical DC Characteristics Notes JN5139-xxxM00/01/03 JN5139-xxxM02/04 Deep sleep current 1.3uA 1.3uA Sleep current 2.6uA 2.
PAGE 5
Jennic The performance of all peripherals is defined in the JN-DS- JN513x Wireless Microcontroller Datasheet [2] Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated antenna have approximately 4 dB less e.i.r.p and reciprocal receive sensitivity.
PAGE 6
Jennic 3. Product Development Jennic supplies all the development tools and networking stacks needed to enable end product development to occur quickly and efficiently. These are all freely available from Jennic’s support website: http://www.jennic.com/support/ . A range of evaluation/developer kits is also available, allowing products to be quickly breadboarded. Efficient development of software applications is enabled by the provision of a complete, unlimited, software developer kit.
PAGE 7
Jennic Antenna 4.
PAGE 8
Jennic 4.1.
PAGE 9
Jennic Pin Signal Function Alternative Function 31 SIF_D Serial Interface data / Intelligent peripheral data out (output) General Purpose Digital I/O DIO15 32 DIO 16 Intelligent peripheral device data in (input) General Purpose Digital I/O 33 CTS1 UART1 Clear To Send (input) / Intelligent peripheral device select (input) General Purpose Digital I/O DIO17 34a RTS1 UART1 Request To Send (output) / Intelligent peripheral interrupt (output) General Purpose Digital I/O DIO18 35 TXD1 UART1 T
PAGE 10
Jennic 5. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. 5.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Min Max Device supply voltage VDD -0.3V 3.6V Voltage on analogue pins: ADC1-4, DAC1-2, COMP1-, COMP1+, COMP2-, COMP2+, DIO9, DIO10, SPISSM, SPISWP, SPICLK, SPIMOSI, SPIMISO, -0.
PAGE 11
Jennic 5.3. Operating Conditions Supply Min Max VDD 2.7V 3.
PAGE 12
Jennic Appendix A Additional Information A.1 Outline Drawing Antenna 18mm J1 30mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.
PAGE 13
Jennic 18mm 9.74mm 4.59 mm 30mm 1.27 mm 2.54 mm 2.76 mm 2.54 mm Thickness: 3.5mm over can, 10.
PAGE 14
Jennic 18mm 9.76mm 6.58 mm 30mm 1.27 mm 2.54 mm 2.76 mm 2.54 mm Thickness: 3.
PAGE 15
Jennic 18mm 7.2mm 4.32 mm 41mm 1.27 mm 2.54 mm . 2.54 mm 2.76 mm Thickness: 3.5mm over can, 10.8mm at SMA connector.
PAGE 16
Jennic 18mm 7.2mm 4.05mm 40.5mm 1.27 mm 2.54 mm . 2.54 mm 2.76 mm Thickness: 3.
PAGE 17
Jennic A.2 Module PCB Footprint Dimensions in mm Note: All modules have the same footprint. Figure 8 Module PCB footprint RF note for –M00 modules with ceramic antenna: No components, ground plane or tracks on any layer of the mother board should be placed within 20mm of the 3 free sides of the antenna. Tracks etc may be placed adjacent to the can, but should not extend past the can towards the antenna end of the module for 20mm from the antenna.
PAGE 18
Jennic A.
PAGE 19
Jennic A.4 Tape and Reel Information: A.4.1 Tape Orientation and dimensions All dimensions are in mm Module type: A B W F E P0 P1 P2 T Cover Tape width (W) JN5139-xxx-M00/03 18.4 30.4 44 20.2 1.75 4.0 2.0 24.0 3.4 37.5 JN5139-xxx-M01 18.4 30.4 56 26.2 1.75 4.0 2.0 24.0 11.2 49.5 JN5139-xxx-M02 18.5 41.5 56 26.2 1.75 4.0 2.0 24.0 11.1 49.5 JN5139-xxx-M04 18.5 40.9 56 26.2 1.75 4.0 2.0 24.0 3.4 49.5 Tolerance ±0.1 ±0.1 ±0.3 ±0.1 +0.1 ±0.1 ±0.
PAGE 20
Jennic A.4.3 Leader and Trailer 300 MM 300 MM A.4.4 Reel Dimensions: Dimensions in mm 20 Module type: A B C N W (min) JN5139-xxx-M00/03 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 44.5 ±0.3 JN5139-xxx-M01/02/04 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 56.5 ±0.
PAGE 21
Jennic A.5 Related Documents [1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology – Part 15.4 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) [2] JN-DS- JN513x Wireless Microcontroller Datasheet [3] JN-RM-2002 802.15.4 Stack API A.
PAGE 22
Jennic A.6.
PAGE 23
Jennic This device has been designed to operate with the antennas listed above. Antennas not included in this list or having a gain greater than 18 dBi are strictly prohibited for use with this device. The required antenna impedance is 50ohms. A.6.2 High Power Module usage limitation The high power module variants are classified as ‘mobile’ device pursuant with FCC § 2.1091 and must not be used at a distance of < 20 cm (8”) from any nearby people.
PAGE 24
Jennic A.7 European R & TTE Directive 1999/5/EC Statement All modules listed in this datasheet are compliant with ETSI EN 300 328V1.7.1 (2006/05) and are subject to Notified Body Opinion RU1548/9025 Issue 2. The modules are approved for use with the antennas listed in the following table. The high power modules M02 and M04 are limited to an antenna with a gain of 2.2 dBi or less. Brand Model Number Description Gain Connector type Antenna Factor ANT-2.4-CW-RCL Vertical - knuckle antenna 2.
PAGE 25
Jennic A.8 Industry Canada Statement To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. These modules have been designed to operate with antennas having a maximum gain of 4.4 dBi. Antennas having a gain greater than 4.4 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
PAGE 26
Jennic A.10 Status Information The status of this Data Sheet is Production. Jennic products progress according to the following format: Advanced The Data Sheet shows the specification of a product in planning or in development. The functionality and electrical performance specifications are target values and may be used as a guide to the final specification. Jennic reserves the right to make changes to the product specification at anytime without notice.
PAGE 27
Jennic A.12 Version Control Version Notes 1.0 1st Issue of Advanced Datasheet 1.1 Update to correct connector positions on drawings and typo on module numbering. –000 modules now read –001. 1.2 Updated to preliminary status, solder reflow profile and antenna lists added. Increased length of –M02 variants 1.3 Updated part numbering and addition of Industry Canada approvals 1.4 Minor specification updates 1.