User Manual

ManualsBrandsNXP Laboratories UK ManualsElectronics802.15.4/ZigBee Module

Table Of Contents

Preliminary Data Sheet – JN5121-xxx-Myy

IEEE802.15.4/ZigBee Module Family

Preliminary - JN-DS-JN5121-xxx-Myy v1.21 © Jennic 2006

Features: Module

•

2.4GHz IEEE802.15.4

compliant

•

2.7-3.6V operation

•

Sleep current (with active

sleep timer) < 14µA

•

JN5121-xxx-M00/01/03

Standard module, 0dBm power

M00: on board antenna or

M01: SMA connector,

M03: RP-SMA connector

> 400m range

o Receiver sensitivity -90dBm

o TX current < 45mA

o RX current < 50mA

o 18x30mm

•

JN5121-xxx-M02/04

18.5dBm power with LNA and

SMA connector, > 4km range

Receiver sensitivity -93dBm

o TX current < 120mA

o RX current < 55mA

o 18x40mm

Features: Microcontroller

•

16MHz 32-bit RISC CPU

•

96kB RAM, 64kB ROM

•

4-input 12-bit ADC, 2 11-bit

DACs, comparator,

temperature sensor

•

2 Application timer/counters,

3 system timers

•

2 UARTs (one for in-system

debug)

•

SPI port with 5 selects

•

2-wire serial interface

•

21 GPIO

•

Evaluation kits available with

full, unlimited, Software

Development Kit

Industrial temperature range

(-20°C to +70°C)

Lead-free and RoHS compliant

Overview Overview

The JN5121-xxx-Myy is a family of surface mounted modules that enable users to implement

IEEE802.15.4 or ZigBee compliant systems with minimum time to market and at the lowest

cost. They remove the need for expensive and lengthy development of custom RF board

designs and test suites. The modules use Jennic’s JN5121 wireless microcontroller to provide

a comprehensive solution, including all RF components. All that is required to develop and

manufacture wireless control or sensing products is to connect a power supply and peripherals

such as switches, actuators, sensors, considerably simplifying product development.

The JN5121-xxx-Myy is a family of surface mounted modules that enable users to implement

IEEE802.15.4 or ZigBee compliant systems with minimum time to market and at the lowest

cost. They remove the need for expensive and lengthy development of custom RF board

designs and test suites. The modules use Jennic’s JN5121 wireless microcontroller to provide

a comprehensive solution, including all RF components. All that is required to develop and

manufacture wireless control or sensing products is to connect a power supply and peripherals

such as switches, actuators, sensors, considerably simplifying product development.

Three basic hardware module variants are available: JN5121-xxx-M00 with an integrated

antenna, JN5121-xxx-M01/M03 with an antenna connector and JN5121-xxx-M02/M04 with a

power amplifier and LNA for extended range. Each of these can be provided pre-programmed

with a ZigBee network stack (JN5121-Z01-Myy) or with customer-specific software.

Three basic hardware module variants are available: JN5121-xxx-M00 with an integrated

antenna, JN5121-xxx-M01/M03 with an antenna connector and JN5121-xxx-M02/M04 with a

power amplifier and LNA for extended range. Each of these can be provided pre-programmed

with a ZigBee network stack (JN5121-Z01-Myy) or with customer-specific software.

Block Diagram Block Diagram

Timers

UARTs

12-bit ADC,

comparator

11-bit DACs,

temp sensor

2-wire serial

SPI

RAM

96kB

128-bit AES

Encrypt ion

Accelerator

2.4GHz

Radio

ROM

64kB

RISC CPU

Power

Management

XTAL

O- QPSK

Mo de m

IEEE802.15.4

MAC

Accelerator

128kB Serial

Flash Memory

JN5121 chip

Power

Bal un

SMA

Connector

Bal un

Ceramic Antenna

Bal un

SMA

Connector

PA / LNA

Ext ernal

Antenna

MO00 Option

M01/03 Option

M02/04 Option

Benefits

•

Microminiature module solutions

•

Ready to use in products

•

Minimises product development

time

•

No RF test required for systems

•

Compliant with FCC part 15

rules, ETSI ETS 300-328 and

Japan ARIB STD-T66

•

Production volumes supplied

pre-programmed with

application software

Applications

•

Robust and secure low power

wireless applications

•

Wireless sensor networks,

particularly IEEE802.15.4 /

ZigBee systems

•

Home and commercial building

automation

•

Home networks

•

Toys and gaming peripherals

•

Industrial systems

•

Telemetry and utilities

(e.g. AMR)

Summary of content (21 pages)

PAGE 1
Preliminary Data Sheet – JN5121-xxx-Myy IEEE802.15.4/ZigBee Module Family Features: Module Overview The JN5121-xxx-Myy is a family of surface mounted modules that enable users to implement IEEE802.15.4 or ZigBee compliant systems with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennic’s JN5121 wireless microcontroller to provide a comprehensive solution, including all RF components.
PAGE 2
Jennic Contents 1. Introduction 1 1.1. 1.2. 1 1 Variants Regulatory Approvals 2. Specifications 2 3. Product Development 3 3.1. 3 JN5121 Single Chip Wireless Microcontroller 4. Pin Configurations 4 4.1. 4.2. 4.3. 4.4. 5 6 6 6 Pin Assignment Pin Descriptions Power Supplies SPI Memory Connections 5. Electrical Characteristics 5.1. Maximum Ratings 5.2. Operating Conditions Appendix A Mechanical and Ordering Information A.1 Outline Drawing A.2 Module PCB Footprint A.3 Ordering Information A.
PAGE 3
Jennic 1. Introduction The JN5121-xxx-Myy module family provides designers with a ready made component which allows IEEE802.15.4 [1] wireless applications, including ZigBee, to be quickly and easily included in product designs. The modules integrate all of the RF components, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennic’s single chip IEEE802.15.
PAGE 4
Jennic 2. Specifications Most specification parameters for the modules are specified in JN-DS-JN5121 Datasheet for JN5121 single chip wireless microcontroller, [2]. Where there are differences, the parameters are defined here. VDD=3.0V @ +25ºC Typ.
PAGE 5
Jennic 3. Product Development Jennic supplies all the development tools and networking stacks needed to enable end product development to occur quickly and efficiently. These are all freely available from Jennic’s support website: http://www.jennic.com/support/ . A range of evaluation/developer kits is also available, allowing products to be quickly breadboarded. Efficient development of software applications is enabled by the provision of a complete, unlimited, software developer kit.
PAGE 6
Jennic Antenna 4.
PAGE 7
Jennic 4.1.
PAGE 8
Jennic Module Pin Signal Function Alternative Function 31 SIF_D General Purpose Digital I/O DIO15 32 DIO 16 Serial Interface data / Intelligent peripheral data t Intelligent peripheral device select General Purpose Digital I/O 33 CTS1 UART1 Clear To Send (input) General Purpose Digital I/O DIO17 34 RTS1 UART1 Request To Send (output) General Purpose Digital I/O DIO18 35 TXD1 UART1 Transmit Data (output) General Purpose Digital I/O DIO19 36 RXD1 UART1 Receive Data (input) General Pu
PAGE 9
Jennic 5. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. 5.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Min Max Device supply voltage VDD1, VDD2 -0.3V 3.6V Voltage on analogue pins ADC1-4, DAC1-2, COMP2M, COMP2P -0.3V VDD + 0.
PAGE 10
Jennic Appendix A Mechanical and Ordering Information A.1 Outline Drawing Antenna 18mm J1 30mm 1.27 mm 2.54 mm 2.54 mm 2.79 mm Thickness: 3mm JN5121-xxx-M00 Outline Drawing 8 Preliminary - JN-DS-JN5121-xxx-Myy v1.
PAGE 11
Jennic 18mm 9.5mm 4.75 mm 30mm 1.27 mm 2.54 mm 2.79 mm 2.54 mm Thickness: 3mm over can, 10.6mm at SMA connector JN5121-xxx-M01/M03 Outline Drawing © Jennic 2006 Preliminary - JN-DS-JN5121-xxx-Myy v1.
PAGE 12
Jennic 18mm 7.6mm 3.8 mm 40mm 1.27 mm 2.54 mm . 2.54 mm 2.79 mm Thickness: 3mm, 10.6mm at SMA connector JN5121-xxx-M02/M04 Outline Drawing 10 Preliminary - JN-DS-JN5121-xxx-Myy v1.
PAGE 13
Jennic A.2 Module PCB Footprint 18mm 1.27 mm 2.54 mm 2.54mm All Pads are 0.9mm square on 1.27mm pitch Note: All modules have the same footprint. © Jennic 2006 Preliminary - JN-DS-JN5121-xxx-Myy v1.
PAGE 14
Jennic A.3 Ordering Information Part Numbering: JN5121 - XXX - MY1Y2 Y3 Y4 Shipping R Box (10 modules per pack) T Tape Mounted 500pcs (00 module only) V Tape Mounted 200pcs (01,02,03,04 modules only) Temp Range / Device Status D -20°C to +70°C, Qualified Module Type 00 Standard Power, Ceramic antenna 01 Standard Power, SMA connector 02 High Power, SMA connector 03 Standard Power, RP-SMA connector 04 High power, RP-SMA connector Software Variant 000 IEEE802.15.
PAGE 15
Jennic A.4 Accessories Product Description Note JNAC001 JN5 serial level converter dongle Connects module UART port to PC serial port to allow code development and debug The JNAC001 RS-232 level converter is used to translate the +/- 7V RS-232 levels to CMOS compatible logic levels. The CMOS levels are made available through a short flying lead with a 6-way IDC socket. This can be connected to the relevant module UART0 pins. The RS-232 Interface is available on a standard nine-way ‘D’ connector.
PAGE 16
Jennic A.5 Tape and Reel Information: A.5.1 Tape Orientation and dimensions Module type: A B W F E P0 P1 P2 T Cover Tape width (W) JN5121-xxx-M00 18.4 30.4 44 20.2 1.75 4.0 2.0 24.0 3.2 37.5 JN5121-xxx-M01/3 18.4 30.4 56 20.2 1.75 4.0 2.0 24.0 11.4 49.5 JN5121-xxx-M02/4 18.4 40.5 56 20.2 1.75 4.0 2.0 24.0 11.4 49.5 Tolerance ±0.1 ±0.1 ±0.3 ±0.1 +0.1 ±0.1 ±0.1 ±0.1 ±0.1 A.5.2 Cover tape details Thickness (T) 0.
PAGE 17
Jennic A.5.3 Leader and Trailer 300 MM 300 MM A.5.4 Reel Dimensions: Module type: A B C N W (min) JN5121-xxx-M00 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 44.5 ±0.3 JN5121-xxxM01/02/03/04 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 56.5 ±0.3 © Jennic 2006 Preliminary - JN-DS-JN5121-xxx-Myy v1.
PAGE 18
Jennic A.6 Related Documents [1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology – Part 15.
PAGE 19
Jennic As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
PAGE 20
Jennic The functionality of the product is final. The electrical performance specifications are target values and may used as a guide to the final specification. Modules are identified with an R suffix, for example JN5121-Z01-M00R. Jennic reserves the right to make changes to the product specification at anytime without notice. Production This is the final Data Sheet for the product. All functional and electrical performance specifications, including minimum and maximum values are final.
PAGE 21
Jennic A.10 Contact Details Corporate Headquarters Jennic Ltd, Furnival Street Sheffield S1 4QT, UK Tel: +44 (0)114 281 2655 Fax: +44 (0) 114 281 2951 info@jennic.com www.jennic.com Jennic Ltd Japan Osakaya building 4F 1-11-8 Higashigotanda Shinagawa-ku Tokyo 141-0022, Japan Tel: +81 3 5449 7501 Fax: +81 3 5449 0741 info@jp.jennic.com www.jennic.com Jennic Ltd Taiwan 19F-1, 182, Sec.2 Tun Hwa S. Road. Taipei 106, Taiwan Tel: +886 2 2735 7357 Fax: +886 2 2739 5687 info@tw.jennic.com www.jennic.