Installation Guide

ManualsBrandsNuTone ManualsCooling & Air QualityOne-bulb Heater/Ventilation Fan, 4.0 Sones

IMPORTANT SAFETY INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service panel to prevent power from being

switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a quali-

fied person(s) in accordance with all applicable codes and stan-

dards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer's guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code authori-

ties.

5. When cutting or drilling into wall or ceiling, do not damage elec-

trical wiring and other hidden utilities.

6. Do not install this unit over a tub or shower.

7. Never place a switch where it can be reached from a tub or

shower.

8. Do not operate unit with dimmer switch or speed control.

CAUTION

1. For general ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

2. This product is designed for installation in flat ceilings only.

DO NOT MOUNT THIS PRODUCT IN A WALL.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Please read specification label on product for further informa-

tion and requirements.

INSTALLATION INSTRUCTIONS

READ & SAVE THESE INSTRUCTIONS!

Bulb Heaters & Bulb Heater/Fans

MODELS: 9417DNM, 9420WHC, 9425WHC

PLAN THE INSTALLATION

Choose the location for your heater. Refer to Warnings and Cau-

tions.

MODELS 9417DNM & 9425WHC ONLY – The unit will operate

most efficiently when located where the shortest possible duct run

and minimum number of elbows will be needed. Units are de-

signed for use with standard 4" round duct.

Note that two-bulb units can be fitted with one infrared bulb (for

heat) and one reflector bulb (for light). Dual or multi-controls can be

used for separate control of bulbs and/or exhaust fan. Purchase

controls separately.

Refer to FIGURE 1

Follow these basic steps when installing this unit:

1. Nail unit to joists.

2. Attach ductwork (Models 9417DNM & 9425WHC only).

3. Connect power cable.

4. Fasten grille to housing.

PREPARE THE HEATER

1. Remove the unit from carton. Save carton for use as plaster

shield in rough-in installations.

Refer to FIGURE 2

2. Slide adjustable mounting brackets into bracket channels on

housing.

FIGURE 1

DAMPER/DUCT

CONNECTOR

POWER CABLE

HOUSING

CEILING

JOIST

CEILING MATERIAL BULB(S)

GRILLE

MOUNTING

BRACKET

FIGURE 2

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS READ & SAVE THESE INSTRUCTIONS! Bulb Heaters & Bulb Heater/Fans MODELS: 9417DNM, 9420WHC, 9425WHC IMPORTANT SAFETY INSTRUCTIONS PLAN THE INSTALLATION WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2.
PAGE 2
INSTALL THE HEATER Refer to FIGURE 3 1. Position unit between joists and extend mounting brackets. 2. Nail brackets firmly to joists. Bottom of brackets should be positioned flush with joist bottom. Refer to FIGURE 4 3. Brackets are factory-set for ½" thick ceiling material. For thicker ceilings, loosen 4 vertical adjusting screws and lower housing to appropriate thickness on gauges. Tighten vertical adjusting screws firmly.
PAGE 3
WHITE to WHITE / GRAY WHITE to WHITE / GRAY RED TO RED BLACK to RED & BLUE GROUND BLACK TO BLUE WHITE to WHITE WHITE to WHITE RED HEAT BLACK GROUND SWITCH OR TIMER GROUND GROUND BLACK VENT BLACK DUAL CONTROL BLACK 120 VAC LINE IN 120 VAC LINE IN MODEL 9417DNM Lamp & Vent operate together WHITE to WHITE / GRAY MODEL 9417DNM Lamp & Vent operate separately RED to RED WHITE to WHITE / GRAY BLACK to BLACK & RED BLACK to BLACK, & YELLOW 3 WHITE / GRAY WIRES RED to RED & BLUE BLACK to BL
PAGE 4
PARTS LIST REF. MODEL 9417DNM-R01 9420WHC-R01 9425WHC-R01 PART NO. PART NO. 9417DNM-R01 PART NO. 1 97010320 97010320 97010319 2 3 4 5 6 7 06170-00 97009724 76230-00 99770033 99770037 ---97009762 06170-00 97010254 98007352 99770033 99770037 97010255 ---- 06170-00 97010254 98007352 99770033 ---97010255 ---- DESCRIPTION Grille Assembly (Includes Ref. No. 2) Grille Spring (2 Req.
PAGE 5
INSTRUCTIONS D’INSTALLATION LISEZ ET CONSERVEZ CES INSTRUCTIONS Ventilateurs à Lampe Chauffante et à Éclairage MODÈLES: 9417DNM, 9420WHC, 9425WHC IMPORTANTES INSTRUCTIONS DE SÛRETÉ PLANIFICATION DE L’INSTALLATION Choisissez l’emplacement du ventilateur. Consultez les avertissements et mises en garde ci-dessus. MODÈLES 9417DNM ET 9425WHC SEULEMENT – L’appareil sera plus efficace s’il est raccordé à un minimum de conduits et de coudes.
PAGE 6
INSTALLATION DU VENTILATEUR Voir FIGURE 3 1. Positionnez l’appareil entre les solives et allongez les brides de montage. 2. Clouez solidement les brides sur les solives. Assurez-vous que le bas des brides est à égalité avec le bas des solives. Voir FIGURE 4 3. Les brides sont réglées à l’usine pour des plafonds de 1/2 po (12 mm) d’épaisseur. Pour des plafonds plus épais, desserrez les quatre vis de réglage vertical et abaissez le boîtier à l’épaisseur appropriée selon les marques de repère.
PAGE 7
ROUGE au ROUGE BLANC au BLANC / GRIS BLANC au BLANC / GRIS NOIR au ROUGE et BLEU BLANC au BLANC TERRE NOIR au BLEU NOIR INTERRUPTEUR ou MINUTERIE CHALEUR ROUGE VENT.
PAGE 8
PIÈCES DE RECHANGE 9420WHC-R01 9425WHC-R01 9417DNM-R01 NO REP. NUM. PIÈCE NUM. PIÈCE NUM. PIÈCE 1 97010320 97010320 97010319 2 3 4 06170-00 97009724 76230-00 06170-00 97010254 98007352 06170-00 97010254 98007352 5 6 7 99770033 99770037 ---97009762 99770033 99770037 97010255 ---- 99770033 ---97010255 ---- DESCRIPTION MODÈLE 9417DNM-R01 Ensemble de grille (inclut no de rep. 2) Ressort de grille (2 Req.