Model APS-997E Owners Guide 2 Way LCD Long Range Vehicle Security & Remote Start System Table Of Contents: Features and Options Page 2 - 4 Arming Your System Page 4 Protection While The System Is Armed Page 5 Disarming The System Page 5 - 6 Intrusion Signals and Tones Page 7 Valet Override, Programming & Safety Control Switch Page 7 Programming Custom Code Override Page 8 - 9 Eliminating the Normal Arm & Disarm Chirps Page 9 Remote Panic Operation Page 10 Remote Control Shock Sensor Sele
5 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable IMPORTANT! In order to provide you with the highest level of security to your vehicle, this system is equipped with selectable manual override circuitry. It is possible that you will need to override you security system if the transmitter becomes lost, or inoperative due to battery failure.
True Last Door Arming (Hardwire Only) Defective Zone By-Pass Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared) 6 Tone Mini Siren Car Horn Output For Additional Alarm Response (Improved Timing To Minimize RF Interference.
If your transmitter button is pressed more than fifty times while it is out of range of the vehicle (children playing with your keys), the transmitter will not operate when you return to the vehicle, and will need to be re-aligned to the receiver. To do this, simply press button 1, (lock), two times within a one second time period. The system will now respond to that transmitter each time a button is pressed.
ARMING THE SYSTEM - PASSIVE (AUTOMATIC) (Must be activated during programming) 1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and trunk lid. The dash mounted LED begins to flash rapidly, indicating 30 second passive arming has begun. 2. Opening any protected entry point during the 30 second passive arming cycle will immediately suspend automatic arming and the 30 second passive arming cycle will restart when all doors are closed.
transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. NOTE: If your transmitter has been configured with single button Lock/Unlock, to activate the all door unlock feature press the Lock/Unlock button a second time within 3 seconds of the first unlock command. 1. As you approach the vehicle, press and release the Unlock/Disarm button on the keychain transmitter. The dash mounted LED turns off.
INTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and the parking lights will flash 3 times when disarming the system. Enter the vehicle and observe the red dash mounted LED to identify which zone was triggered. If the LED is flashing one time...pause...one time...pause...etc.
PROGRAMMING YOUR CUSTOM OVERRIDE CODE Unlike override switches easily found, and defeated, this security system allows the consumer to program a personal override code, offering a higher level of security. To take advantage of this option, programmable feature # 9 must be selected for the Custom Code Option. Consult your installation center for programming details. The system comes from the factory with a pre-programmed override code of 11. To change this default override code, do the following: 1.
You will notice the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory. NOTE: If after step 7, the LED flashes a code other than what was just entered, this indicates that the code has not been changed. You will have to repeat steps 1 through 7 above being certain to note the following: Acceptable digits 10ths or units are 1 through 9.
REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic: 1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds.
1. Within 2 seconds of arming, press and release the ARM button 1 time, to defeat the pre-detect stage of the shock sensor. (The lights will flash and the siren will chirp once.) 2. Within 2 seconds of step 1, press and release the ARM button 2 times, to defeat the pre and full detect stages of the shock sensor. (The lights will flash and the siren will chirp twice.) 3. Within 2 seconds of step 1, press and release the ARM button 3 times to enter the "City Mode" of operation.
TO REMOTE START THE VEHICLE Press and release the programmed channel of your keychain transmitter two times within 2 seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15, or 20 minutes. As a visual indication, the parking lights will flash or turn on depending on the programming set up by your installation center. When you arrive at your vehicle, disarm the alarm system by pressing and releasing the arm/disarm button of your keychain transmitter.
1. Start the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times. 2. Shut off the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times. 3. Within 10 seconds of step 2, activate the RF start command two times. (Push the second channel button of your keychain transmitter 4 times). The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated.
Other Transmitter button configurations are also available. Consult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system. This security system has an additional feature that can be connected to a number of different optional accessories.
Other Transmitter button configurations are also available. Consult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system. This security system has an additional feature that can be connected to a number of different optional accessories.
When Disarmed, Press the Arm/Lock button to Lock and Arm the System. The Lock Icon is displayed on the LCD panel & the parking lights flash once. When Armed, Press the Disarm/Unlock button to Unlock and Disarm the System. The Unlock Icon is displayed on the LCD panel and the parking lights flash twice. When the Key Icon Button Has Been Operated for 3 seconds the trunk open icon will flash on the LED Screen.
Triggered and entry attempt was made to the vehicles glass, or the vehicle has been hit or bumped hard enough to cause a response from the vibration detector. ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE: If th e a rm /d i s a rm chi rp tones have been turned off at the vehicle, when you arm, or disarm, the display will indicate this as shown A and there will be no arm/disarm chirps at the transmitter. This is true if the transmitter is set for vibrate mode as well.
PRESTIGE 24 S A Trunk Release/ Remote Start 12 Z Z Option F Function Button IGN INHIBIT AM PM Lock/Arm 0 Unlock/Disarm ADDITIONAL REMOTE FEATURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start.
To activate this function, (a) Turn the ignition switch off. (b) W ithin 10 seconds of step (a), depress and hold the brake pedal, while pressing the key icon transmitter button 2 times. (c) The unit will emit 2 chirps, the transmitter will beep and the 24 Hour start timer icon on the display will remain on. The vehicle will start at the set time 24 hours from when set. To toggle this feature off, press the option + lock buttons simultaneously until a beep is heard and the 24 hr timer turns off.
PRESTIGE 24 S A 12 Z Z IGN INHIBIT AM PM 0 lock buttons, the trunk/key icon button operates remote start and remote trunk release where applicable. The option button and any button combination may be programmed to operate various options. Consult your installation center for button programming and options that may have been added to your vehicle. Although this is the default programming from the factory, this can be changed for you to any configuration you prefer.
24 HOUR START TIMER Standing at the vehicle at the time you want it to start, press the option + lock buttons simultaneously for 1 seconds. The transmitter will beep and 24 display the 24 hr timer. This is the time the vehicle will start when you follow the exit procedure. In other words, if you want the vehicle to start 6AM, at 6AM of any morning, standing at the vehicle, press and hold the option + lock buttons until you hear a beep and the 24 hr timer is displayed. This establishes a starting time.
TRANSMITTER FUNCTION SELECTION TIMING ADJUST MODE (HRS) TIMING ADJUST MODE (MINS) ALARM CLOCK ADJUST MODE (HRS) ALARM CLOCK ADJUST MODE (MINS) TRANSMITTER BUTTON PRESS FOR 5 SECONDS AM PM 18:88 F PRESS 1X AM PM 18:88 F PRESS 2X AM PM 18:88 AM PM 18:88 F F PRESS 3X ALARM CLOCK & POWER UP MUSIC SELECT F PRESS 4X ALARM CLOCK ADJUST MODE ON/OFF F PRESS 5X TIMING COUNT DOWN ADJUST MODE (HRS) ICON DISPLAYED F 8 2 BEEP TONES 5 SELECTIONS PRESS KEY BUTTON OR OPTION BUTTON TO SELECT ON/O
APS 997E SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = REARMING SLOW FLASHING = OFF = ON SOLID = 3 FLASH...PAUSE = 2 FLASH...PAUSE = 1 FLASH...PAUSE = PASSIVE ARMING/ACTIVE ARMED DISARMED VALET MODE INTRUSION ZONE 3 INTRUSION ZONE 2 INTRUSION ZONE 1 SIREN CHIRP INDICATORS 1 CHIRP * = ARM 2 CHIRPS * = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated.
PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS (BANK 1) Transmitter Model Name 145SP or 5BCR14SP Is Also Found On Back Of Transmitter Case. Use Battery CR2032 For 145SP & AAA For 5BCR14SP. 1) Turn the ignition key to the on position. 2) Press and release the valet/programming switch 3 times (Siren Chirps). 3) Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren. 4) Turn the ignition switch off.