User's Manual

ManualsBrandsNutek ManualsElectronicsTransmitter

Using Your Remote Control

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press the LOCK icon button on the remote

control. The system will sound twice and the parking lights will flash twice, indicating the system is

armed. The doors will also lock at this time (if equipped and connected). The blue dash mounted

status indicator light will blink steadily, once per second. To arm the system silently, press and hold the

LOCK icon button for 2 seconds. The parking lights will flash 2 times indicating the system is armed

and has locked the doors (if equipped and connected). The blue dash mounted status indicator will

blink steadily, once per second.

Pre-arm Mode

If the system sounds and the parking lights flash only once, this indicates that the vehicle’s interior light

is on or an entrance is left open. Check to see that all doors hood and trunk are closed properly. Once

all entrances are secured (and the interior light is off), this system will sound/flash again. The system

is now fully armed (If the entrance is not secured within 4 minutes, the system will arm and ignore the

unsecured entrance until it is closed.)

Disarming the Security System

To disarm the system press the UNLOCK icon button. The system will sound and the parking lights will

flash once, and the doors will unlock (if equipped and connected). To disarm the system silently, press

and hold the UNLOCK icon button for 2 seconds. The parking lights will flash, indicating the system is

disarmed and has unlocked the doors (if equipped and connected).

Disabling/Enabling Confirmation Chirps

1. Turn the ignition key ON then OFF.

2. Within 10 seconds push and release the valet/override button 3 times.

3. The system will sound 2 times to disable confirmation chirps or 1 time to enable confirmation

chirps.

Attempted Intrusion Identification

This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If

an intrusion attempt occurred, the system will sound 4 times and the parking lights will flash 3 times

when disarming the system. Enter the vehicle an observe the blue dash mounted status indicator light

to Identify which zone was triggered.

1. IT-s Interior Theft Sensor- 1 flash, pause 1 flash, etc.

2. Hood or Trunk Pin switch- 2 flashes, pause 2 flashes, etc.

3. Door Entry- 3 flashes, pause 3 flashes, etc.

The intrusion warning indicators are stored in the system’s memory and will be erased when the ignition

key is turned on.

*Throughout this manual, ‘press’ refers to pressing for less than 1 second.

Summary of content (4 pages)

PAGE 1
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the LOCK icon button on the remote control. The system will sound twice and the parking lights will flash twice, indicating the system is armed. The doors will also lock at this time (if equipped and connected). The blue dash mounted status indicator light will blink steadily, once per second. To arm the system silently, press and hold the LOCK icon button for 2 seconds.
PAGE 2
Using Your Remote Control, continued Two Stage Door Unlock If this feature is enabled on your system, pressing the UNLOCK icon button one time on the remote control will unlock only the driver’s door. Press the UNLOCK icon button again to unlock the remaining doors. Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the TRUNK icon button on the remote control for 2 seconds will open the vehicle’s trunk or hatch.
PAGE 3
Using Your Remote Control, continued Using the “Quick-stop” Feature If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you. To engage quick stop: 1. Stop the vehicle and place the transmission in PARK. 2. With your foot off the brake pedal, press and release the KEY button on the remote control two (2) times within 2 seconds.
PAGE 4
Using Your Remote Vehicle Starter, continued To begin the 2 / 4 hour start up timer mode from the remote control: 1. Activate the remote vehicle start feature using the remote control. 2. Shutdown the remote vehicle starter using the remote control (press the KEY button 2 times). 3. Within 10 seconds press KEY button on the remote control 4 times. The parking lights will flash and the system will sound 4 times indicating the 2 / 4 hour start up timer mode has been activated.