RS-230-DP Deluxe Keyless Entry & Remote Start July 27, 2010 Operation Guide Temporary cover. Color cover is in a separate file.
Table Of Contents Introduction.............................................................................................2 The Transmitter......................................................................................3 Transmitter Functions.............................................................................3 Other Remote Start Features.................................................................4 Low Battery/Low Temp Automatic Starting.........................................
The Transmitter Transmitter part number: 113-03 Call your dealer or visit www.caralarm.com to order replacement transmitters. Transmitter battery replacement: Remove the small screw from the lower back case, and separate the transmitter halves. Replace the 2 CR2016 batteries and reassemble the transmitter case. “start”/”unlock” button Transmitter Functions REMOTE START: Press and release the “START” button twice.
Transmitter Functions (cont’d) UNLOCK: Press and hold the button for 3 seconds. • The doors will UNlock, the parking lights will flash TWICE Then illuminate for 30 seconds. Other Remote Start Features Low Battery/Low Temp Automatic Starting This feature will automatically start the engine should the vehicle battery drop below 11 volts or the interior temperature drop to 15 (or 32) degrees fahrenheit. This feature is very useful when the vehicle is parked for a long period of time in cold climates.
The Status Lights The Status Light helps to visually confirms the status of the system and provides a high level of visual deterrence. The Status Light is located in the window mount receiver unit. Normal System Status 1) Off = The remote starter system is off, in standby mode. 2) On Constant = The system is in the Valet Mode, with the remote starter system disabled. Starting System Status The Status Light also indicates the remote start status: 3) Flashing Slow (once per second): Remote start is on.
Using The Valet Switch Valet Mode Valet mode prevents the remote start feature from being activated. It should be used, for example, when you have your vehicle serviced. To engage Valet Mode: • With the system “unlocked”, press and hold the Valet Switch for 3 seconds; the Status Light will turn on and stay on to indicate Valet Mode. Attempts to remote start will result in no response. Keep this in mind if remote start stops functioning. • To turn off Valet Mode, simply press & release the Valet Switch once.
Programming Features Step 1 Turn the ignition key “ON”, then “OFF” Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user features (10 times to access installer features). ~ The parking lights and the status light will turn on. Step 3 Within 10 seconds of step 2, press the valet switch the number of times corresponding with the desired feature’s number. ~ The status lights and the parking lights will flash equal to the selected feature.
Installer Programmable Features This group of Installer Programmable Features are all accessed as a group in the second level of features’ programming.
Installer Programmable Features (cont’d) Feature #4 Satellite Relay Port Green Wire Function Starter (press the brake pedal 1 time to program) - DEFAULT Pulse After Engine Start (press the brake pedal 2 times to program) Status Output (press the brake pedal 3 times to program) Domelight (press the brake pedal 4 times to program) This feature changes the operation of the Green wire (negative) on the satellite relay port.
Installer Programmable Features (cont’d) Feature #8 Remote Start Lock Control Off (press the brake pedal 1 time to program) - DEFAULT Unlock before start (press the brake pedal 3 times to program) This feature allows for OEM alarm/lock control in relation to remote start operations thus eliminating extra wiring.
Programmable Features Matrix User Feature Programming: Ignition on, off, press valet 5 times # Feature Brake Pedal x 1 Brake Pedal x 2 Brake Pedal x 3 Brake Pedal x 4 1 Engine Run Time 10 min 5 min 15 min 20 min 2 Steady/Flashing lights for RS Steady Flashing Installer Feature Programming: Ignition on, off, press valet 10 times 1 RS Activation 2 Engine Detection 3 Gas or Diesel Engine 1 press 2 presses 3 presses 4 presses Tachless Hi Tachless Lo Tach Wire Datatach Diesel (20 sec delay)
Back Cover Color cover is in a separate file.