Professional Disc Jockey Products CM-100 PROFESSIONAL DJ MIXER USER’S MANUAL ©1999 Industries http://www.numark.
CM100 Safety Information h) Power Sources - This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit. i) Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord.
CM100 VERY IMPORTANT Please read this entire manual before connecting this unit to your system For optimum performance: • • • • • • • • • The crossfader is a user replaceable item and subject to wear. Excessive force can wear out the fader quickly. This is not a warranted item. Never use spray cleaners on the slide controls. Residues cause excessive dirt build-up and this will void your warranty. In normal use slide controls can last for many years.
CM100 CM100 PROFESSIONAL DJ MIXER CONGRATULATIONS! You have purchased the CM100 Stereo Mixer by . This mixer has been designed to provide dependable control over your input and output sources. Whether you install this piece in a permanent environment or take it on the road, you are sure to utilize the features of the CM100. The CM100 features all new circuitry and the latest in manufacturing and design technology to give you greater quality and better reliability than ever before.
CM100 TABLE OF CONTENTS Safety Measures 2 Important Information 3 Registration 3 Introduction 4 Quick Setup Diagram 7 Description of the Features 8 Specifications 11 Warranty 12 - The Leader in DJ Technology ©1999 Industries -5- http://www.numark.
CM100 - The Leader in DJ Technology ©1999 Industries -6- http://www.numark.
CM100 QUICK SETUP DIAGRAM Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all stereo input sources. Next, connect your microphone(s) and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio sources. Plug your mixer into AC power. Now you are ready to switch everything on. Always switch on your audio input sources such as turntables or CD players first, then your mixer, and finally any amplifiers.
CM100 MIXER FEATURES 8 3 2 4 5 7 6 9 3. 4. 5. 6. 7. 26 12 14 20 18 13 23 10 17 We have divided this section into various functional blocks: Inputs, Microphone, Crossfader, Equalizer, Outputs, and Headphone Cueing. It is important to learn how each of these work. INPUTS 2. 19 1 11 1. 25 16 15 8. 21 22 24 Neutrik™ “Combo” connector - allows connection of either a 1/4” jack or an XLR jack. This is ideal for connecting an XLR gooseneck directly into the mixer. CROSSFADER 9.
CM100 EQUALIZER 12. 5-Band Stereo Graphic Equalizer (EQ) compensates for differences in source material sound quality. In ultra-compact mobile systems this EQ can be used to tailor the sound to the acoustical requirements of the room. Center frequencies are 63Hz, 250Hz, 1kHz, 4kHz and 16kHz. Faders have a center detent for an accurate "flat” response. Below is a typical "house" EQ curve. Notice how the knobs above "0" balance out the knobs below.
CM100 REAR PANEL FEATURES 38 36 40 29 39 28 31 37 35 34 33 32 27. Phono Inputs – for attaching your turntables. When these connectors are used, your signal is fed directly to the high-quality RIAA phono pre-amplifiers. Use this position only for turntables. Line level sources will overload the sensitive phono pre-amps and will cause distortion. 28. Grounding lug - for turntable connection. Always use this connection when using turntables. (your turntable cable should have a grounding wire) 29.
CM100 SPECIFICATIONS INPUTS: Line: 10kΩ input impedance 85mV rms sensitivity (for 1.22V output) Mic: 10kΩ input impedance unbalanced 2 mV rms sensitivity (for 1.22V output) 60mV rms max input Phono:47kΩ input impedance 1.5mV rms sensitivity @ 1 KHz (for 1.22V output) OUTPUTS: Line: 9V rms max Headphone Amp: 0.5 watt into 47Ω Distortion less than 0.01% SIGNAL TO NOISE RATIOS* (vs.
Professional Disc Jockey Products LIMITED PRODUCT WARRANTY What is covered and for how long? 1. NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK'S DJ mixers and amplifiers are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer and continuing for the following period of time after that date for (2) Years.