Operating Manual
Button function and battery install specification
B
Open the back cover
1.5V dry cell
seven×2
Match code key CODE【 】
Programme key SET【 】
Open the back cover with
force’s direction
Install the back cover
with force’s direction
Contrar y
CODE
SET
Front
Display channel 9 or 99
(P represents group control)
Channel Key
Up Key
Stop Key
Down Key
H12022 A/3
Transmitter Operating Manual
Company reserves the right to change product design and specifications without prior notice then photos are for reference only.
CODE
SET
CODE
SET
Lock channel: :
CODE
SET
factor y default is the maximum channel
Display the maximum
channel and flicker
4、Display channel P;
A
A
B
!
CODE
SET
CODE
SET
CODE
SET
CODE
SET
CODE
SET
Adjust the third limit:
Repeat the operation once to eliminate the third limit:
Press [up/down] button to
move blinds, and then stop
blinds at the appointed position.
Tool with 3 mm diameter or less.
Motor response:
rotate back and for th
once.
Third limit position
Up limit position
Down limit position
1、Select the channel that
will be used to adjust limits;
3、Press & Hold Set button on
transmitter about 10s
【 】
2、Blinds moves to the
third limit position;
4
press Down button about 5s;
、Within 10s af ter motor stops,
【 】
Motor response:
Rotate back and for th once.
Now you can start
to adjust limits
5、
;
Within 10s af ter motor stops,
press Stop button about 5s【 】
Motor response:
Rotate back and for th once.
Successful to adjust
the third limits
① Set the third limit between up and down limit , as the half
position of blinds;
② Reset up and down l imit, or rep eat third limi t setting steps
will elim inate the third limit;
③ Press & Hold [stop ] button about 3 s;
4、Within 10s af ter motor stops,
press【Down】button about 5s;
5、Within 10s press Up
button to adjust up limit;
【 】
2、Select the channel that
will be used to adjust limits;
Adjust up limit
8、Within 10s press Down
button to adjust down limit ;
【 】
10、Press & hold Stop + Down
about 1s to save down limit;
【 】
Adjust down limit
7、Press & hold Stop + Up
about 1s to save up limit;
【 】
Motor response:
rotate back
Confirm that blinds stops
at the up limit position
Press stop button
when blinds is near
the appointed position.
Save up limit
6、Press Up/Down button to
move blinds, and then stop blinds
at the appointed position;
【 】
9、Press Up/Down button to move
blinds, and then stop blinds at the
appointed position;
【 】
Save down limit
Confirm that blinds stops
at the down limit position
Press stop button when
blinds is near the
appointed position.
3、Press & Hold Set button on
transmitter about 10s;
【 】
Confirm direction
[ ]Up button
[Down] button
1、Press up button, blinds up.
Press down button, blinds down;
If direction is not logical, please
reset direction according
“Reset direction”steps.
Adjusting Limits:
When you press Up or Down button the blinds will move up or down and stop automatically at the appointed position【 】 【 】 , 。
Now you can start
to adjust limits
Tool with 3 mm diameter or less
Motor response:
rotate back and for th once.
Motor response:
rotate back and
forth once.
Motor response:
rotate back
Reset direction :
Reset motor direction
up button,blinds run up。
。Such as: before reset,press transmitter up button,blinds run down。After reset,press transmitter
2、Press & Hold Set button
on transmitter about 10s;
【 】
3、
press Stop button about 5s
Within 10s af ter motor stops,
【 】 ;
Motor response:
rotate back and for th once.
1、Select the channel that
will be reset direction;
Tool with 3 mm diameter or less
Motor response:
rotate back and for th once.
Copy:
Add a new channel to control motor (No need to touch motor):。
1、Select the channel that
will be copied;
2、
transmitter about 10s
Press & Hold Code button on【 】
3、Within 10s af ter motor stops,
pair on the new channe;
Tool with 3 mm diameter or less
Motor response:
rotate back and for th once.
Tool with 3 mm diameter or less
Motor response:
rotate back and for th once.
A transmitt er
A transmitt er B transmitt er
Speed setting:
Two speed can be adjusted,
Default is first:
Motor response:
rotate back and for th three times.
1、 【 】
;
Press & Hold Set button
on motor about 15s
1、Press & Hold Set
button on motor about 10s
【 】
;
2、Press Set button on motor again;【 】
Clear pairing :
Clear all pairing on the motor
:
Motor response:
rotate back and for th twice.
Motor response:
rotate back and for th once.
1、Select the channel
that will be paired;
2、Press Set button on motor;【 】
Motor response:
rotate back and for th once.
Tool with 3 mm diameter or less
3、Within 10s af ter motor stops,
press 【Code】 button;
Motor response:
rotate back and for th once.
Pairing transmitter and motor:
Repeat the pairing operation once to eliminate the current pairing。A motor stores up to 10 transmitter
channels,Adding a new transmitter channel will cover the earliest channel For example, current paired
channels are 1~10 If you add channel 11 paired channels will be 2~11 :
。
。 , 。
Instructions
I
( *Take A3 button transmitter as an example,For other transmitters please refer to
the corresponding transmitter manual。)
,
Inching / Continuous moving interchange:
Default is continuous moving. After switching to inching moving, press & hold Up or Down
button about 2s, motor will continuously moves:
【 】 【 】
1、Select the channel that
will be interchanged;
2、Press & Hold Set button on
transmitter about 10s;
【 】
3、Within 10s af ter motor stops,
press【Up】button about 5s;
Tool with 3 mm diameter or less
Motor response:
rotate back and for th once.
Motor response:
rotate back and for th once.
2、With in 6s, press
Select-button to choose
channel you want to lock;
3
to save the currently
locked channel
、Press the【Stop key 】
1、
Set key about 10s
Keep press transmitter
【 】 ;
Tool with 3 mm diameter or less