Mobile Media Center for Dual Flat-Screen TVs User Manual SKU#: STNDMTVDUO For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements Safety Measures • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. Mesures de sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Assemble this product according to the instructions. • Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. • Weight capacity of the Multimedia Shelf: 5 kg (11 lb.) • Weight capacity of the Camera Shelf: 5 kg (11 lb.) • Weight capacity of the TV mount: 50 kg (110 lb.
• Produkten är endast avsedd för användning inomhus och ska inte användas utomhus. • Dra inte åt skruvarna för hårt när du monterar produkten. Om du måste ta i när du skruvar åt kan du sluta skruva åt. • Det krävs två personer för att montera produkten. Försök inte montera produkten och installera utrustning utan hjälp. • Innan du lägger till utrustning på produkten, se till att produkten är korrekt monterad, installerad och att produkten klarar av vikten på utrustningen som du lägger till.
dit product begint. • Rijd de wagen niet over snoeren, kabels of ongelijke oppervlakken. • Voordat u de wagen gaat verplaatsen, moet u de zwenkwielen ontgrendelen. • Kantelgevaar! Dit product is vrijstaand en kan daarom kantelen bij verkeerde behandeling of overbelasting. Wees voorzichtig bij het verplaatsen, laden, lossen en aanpassen van het product. Als u dit niet doet, kan dit leiden tot schade aan de apparatuur en / of persoonlijk letsel.
Dichiarazioni di avvertenza • Assicurarsi di Assemblare il prodotto secondo le istruzioni. • Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima di iniziare ad assemblare e a utilizzare questo prodotto. • Non superare la capacità di carico del prodotto. Il sovraccarico del prodotto potrebbe causare danni o lesioni.
• Capacité de poids de l’étagère pour caméra : 5 kg • Capacité de poids du support d’écran : 50 kg x 2 • N’autorisez pas les enfants à grimper sur ce produit ni à l’utiliser sans surveillance. • Ce produit est uniquement destiné à une utilisation en intérieur et ne doit pas être utilisé à l’extérieur. • Ne serrez pas trop les vis lors de l’assemblage de ce produit. Si vous rencontrez une résistance lors du serrage des vis, cessez de serrer. • L’assemblage de ce produit nécessite deux personnes.
• Antes de adicionar o equipamento a este produto, certifique-se de que o montou e instalou devidamente e de que o produto pode suportar o peso do equipamento que está a adicionar ao mesmo. • Certifique-se de que instala devidamente todo o seu equipamento antes de começar a ajustar este produto. • Não mova o carro pelos fios, cabos ou superfícies irregulares. • Antes de começar a mover o carro, certifique-se de que desbloqueia os rodízios.
• Antes de empezar a mover el carrito, asegúrese de haber desbloqueado las ruedas. Antes de empezar a mover el carrito, asegúrese de haber desbloqueado las ruedas. • ¡Peligro de vuelco! Este producto es independiente y, por lo tanto, propenso a volcarse si se manipula incorrectamente o se sobrecarga. Tenga cuidado al mover, cargar, descargar y ajustar el producto. El no hacerlo podría resultar en daños al equipo y / o lesiones personales.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Diagram.....................................................................................1 Front-Angled View...........................................................................
Product Diagram Front-Angled View Camera Shelf (M) Connecting Plate (L) Left TV Mounting Brackets (G) Universal Plates (C) Left Column (E) Right TV Mounting Brackets (H) Right Column (F) Support Bar (O) Media Shelf (K) Casters (B) Base (A) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions Front View To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents Base (A) Casters (B) Qty: 1 Qty: 4 Left Column (E) Right Column (F) Qty: 1 Qty: 1 Top Covers (I) Qty: 2 Universal Plates (C) Qty: 2 Left TV Mounting Brackets (G) Qty: 2 Connectors (J) Media Shelf (K) Qty: 2 Qty: 1 Handles (D) Qty: 2 Right TV Mounting Brackets (H) Qty: 2 Connecting Plate (L) Qty: 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Camera Shelf (M) Qty: 1 Fixing Plates (N) Support Bar (O) Knobs (P) Qty: 2 Qty: 1 Qty: 2 M6 x 15 mm Screws (Q) M6 x 25 mm Button Head Screws (R) M6 x 25 mm Hex Head Screws (S) M4 x 6 mm Screws (T) Qty: 2 Qty: 3 M6 x 25 mm Hex Head Screws (V) M6 x 14 mm Screws (W) M8 x 25 mm Hex Head Screws (X) Qty: 2 Qty: 10 Qty: 8 Qty: 4 M4 x 6 mm Button Head Screws (U) Qty: 2 Qty: 2 4
Connecting Plate Spacers (Z) Connecting Plate Washers (A1) Qty: 2 Qty: 2 M5 x 14 mm Button Head Screws (M-A) M6 x 14 mm Button Head Screws (M-B) M6 x 30 mm Button Head Screws (M-C) Qty: 8 Qty: 8 Qty: 8 M8 x 30 mm Button Head Screws (M-D) M8 x 50 mm Button Head Screws (M-E) Square Washers (M-F) Small Spacers (M-G) Qty: 8 Qty: 8 Qty: 8 Qty: 16 M6 x 25 mm Button Head Screws (Y) Qty: 2 Wrench (C1) Qty: 1 5 Hex Key (B1) Qty: 1
Large Spacers (M-H) User Manual Qty: 16 Qty: 1 Requirements For the latest requirements, please visit www.startech.com/STNDMTVDUO • TVs x 2 • (Optional) Web Camera x 1 • (Optional) Media Device (e.g. DVD Player) x 1 • (Optional) Padlocks x 2 • Phillips Head Screwdriver x 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installation Attach the Casters (B) Casters (B) Wrench (C1) Nut Figure 1 1. Flip the Base (A) upside down and place it onto a clean and flat surface. (Figure 1) Note: Cover hard floors with a soft cloth to prevent scratching. 2. Insert each of the four Casters (B) into the holes, located in the bottom of the Base (A) and tighten, using the Wrench (C1). 3. Flip the Base (A) upright so the Casters (B) are making contact with the floor. 4.
Attach the Columns (E&F) to the Base (A) Inner Left Column (E) Hex Key (B1) Outer Left Column (E) Figure 2 1. Determine the desired mounting height for the TV. 2. Hold the inner and outer Left Column (E) in one hand and loosen the two Hex Screws on the side of the Left Column (E), using the Hex Key (B1). (Figure 2) Notes: Two People may be required to complete this step. Do not release the grip on the inner and outer portions of the Left Column (E) while the Hex Screws are loose. 3.
Handle (D) Columns Figure 3 Base (A) 6. Engage the Brake on each one of the four Casters (B) before proceeding to step 7. (Figure 3) 7. Slide the Left (E) and Right Columns (F) into their respective receptacles, located in the Base (A). Note: The Cable Management Holes in the Columns (E+F) must be facing the front of the assembly. 8. Slide one Handle (D) over the Left Column (E). Ensure the grip loop portion of the Handle (D) is facing the back of the Base (A).
Base (A) Hex Key (B1) M8 x 25 mm Hex Head Screws (X) Figure 4 10. Tilt the entire Assembly onto its side to gain access to the bottom of the Base (A). (Figure 4) Note: It is recommended that Two People complete this step and any subsequent steps that involve tilting or moving the Mobile TV Cart. 11. Insert four M8 x 25 mm Hex Head Screws (X) through the Base (A) and into the Left Column (E). 12. Tighten all four M8 x 25 mm Hex Head Screws (X), using the Hex Key (B1). 13.
M6 x 25 mm Screw (S) Figure 5 Assemble the Universal Plates (C) Screw Holes Plastic End Cap Figure 6 1. Place the Universal Plates (C) next to one another on a clean and flat surface with the Plastic End Caps facing the outer edges and the Screw Holes facing down. (Figure 6) 2. Slide one Connector (J) into each Universal Plate (C). Note: Both Connectors (J) must be oriented the same way. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
3. Flip the Universal Plates (C) and place them next to one another with the Plastic End Caps facing the outside edges and the Screw Holes facing up. 4. Slide two Fixing Plates (N) into the grooves of the Universal Plates (C), located underneath the Screw Holes. Align the Screw Holes in the Universal Plates (C) with the Holes in the Fixing Plates (N). 5. Insert four M6 x 14 mm Screws (W) through the Screw Holes in the Universal Plates (C) and into the Fixing Plates (N). 6.
4. Affix one Top Cover (I) over each Column (E+F). (Figure 8) Top Cover (I) Left Column (E) Figure 8 Assemble the Media Shelf (K) Figure 9 1. Flip the Media Shelf (K) upside down and place on a clean and flat surface. 2. Place the Support Bar (O) up against the Media Shelf (K), aligning the holes in the Support Bar (O) with the holes found in the Media Shelf (K). (Figure 9) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
3. Hold one of the Knobs (P) up against the outermost hole in the Support Bar (O) and insert one of the M6 x 25 mm Button Head Screws (Y) through the square shaped hole in the Media Shelf (K), the Support Bar (O), and into the Knob (P). 4. Tighten the Knob, by hand. 5. Repeat steps 3-4 to attach the second Knob. 6. Insert two M6 x 14 mm Screws (W) through the innermost circular shaped holes in the Media Shelf (K) and into the Support Bar (O). 7.
1. Lower the Media Shelf (K) Assembly from above into the Supporting Blocks, located on the insides of the Columns (E+F). Align the holes in the Support Bar (O) with the holes in the Supporting Blocks. (Figure 10) 2. Insert one M6 x 25 mm Hex Head Screw (V) through the hole in the Supporting Block on the Left Column (E) and into the Support Bar (O). 3. Tighten the M6 x 25 mm Hex Head Screw (V), using the Hex Key (B1). 4. Repeat steps 2-3 for the Right Column (F). 5.
Adjust the Height of the Columns (E+F) Hex Screws Figure 11 1. Loosen the two Hex Screws in each Column (E+F) (4 Hex Screws total), using the Hex Key (B1), while supporting the full weight of the Universal Plate Assembly (C+J). (Figure 11) Warning! Once all of the Hex Screws have been loosened, the full weight of the Universal Plate Assembly (C+J) will become unsupported. Ensure the full weight of the Universal Plate Assembly (C+J) is supported until the Hex Screws have been adequately tightened. 2.
Attach the TV Mounting Brackets (G+H) Figure 12 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
1. Place one TV on a flat, clean, and padded surface with the screen side down. (Figure 12) 2. (Optional) Identify and remove the pre-installed VESA Hardware from the back of the TV. Note: Not all TVs will have placeholder VESA Hardware. Only remove the four Screws for the VESA Mount. Do not remove any of the screws from the TV’s structural assembly. 3. Place the necessary number of Small (M-G) and/or Large Spacers (M-H) over each VESA Mounting Hole. 4.
Hang the TV onto the Universal Plate (C) Figure 13 Warning! Ensure the TVs are correctly mounted onto the Universal Plates (C) and the locking mechanisms are properly engaged before releasing the displays. 1. Select the first TV to be mounted and loosen the 2 Screws, located at the bottom of the TV Mounting Brackets (G+H), using a Phillips Head Screwdriver. (Figure 13) Note: Loosening the Screws lowers the locking mechanisms, located on the TV Mounting Brackets (G+H).
4. (Optional - Locking) Insert a Padlock (not included) through the holes, located at the bottom of either TV Mounting Bracket (G+H). 5. Repeat steps 1-4 for the second TV. Assemble the Camera Shelf (M) Figure 14 1. Hold the Camera Shelf (M) up against the top of the Connecting Plate (L), aligning the three holes in the top of the Camera Shelf (M) with the three holes in the Connecting Plate (L). (Figure 14) 2.
Attach the Camera Shelf (M) Assembly Figure 15 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
1. Prepare two M6 x 25 mm Button Head Screw (R) Assemblies by threading a Connecting Plate Washer (A1) over each M6 x 25 mm Button Head Screw (R). 2. Select the two openings in the Connecting Plate (L) that will provide the optimal mounting height for the Camera Shelf. Insert one of the M6 x 25 mm Button Head Screw (R) Assemblies through the Connecting Plate (L). Insert the second M6 x 25 mm Button Head Screw (R) Assembly through the opening next to the first M6 x 25 mm Button Head Screw (R) Assembly.
Cable Management Figure 16 1. Route the Cables from the back of the TVs into the Grommets located at the top-front of the Columns (E+F). (Figure 16) Note: All the Grommets are removable. 2. Push the Cables through the Columns (E+F). 3. Route the Cables out of the Grommets, located at the bottom-front of the Columns and into the respective Power and/or Video Sources. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Operation Figure 17 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjust the Tilt Angle of the TV Mounting Brackets 1. Loosen the two Nuts on the outward facing side of one TV Mounting Bracket (G or H), using the Wrench (C1). 2. Repeat step 1 for the second TV Mounting Bracket (G or H). 3. Tilt the TV to the desired angle. Note: Two People are required for all tilt adjustments. 4. Tighten the four Nuts that were loosened in steps 1-2, using the Wrench (C1).
Warranty Information This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
