User's Manual

ManualsBrandsNortek Security & Control ManualsElectronicsLife Shield Keypad

Wireless Keypad SKP2

The SKP2 is a Wireless Keypad with Stay, Away, and Instant

arming modes as well as panic emergency mode. The Keypad

includes a display and status LED to indicate the current status of

the system. The Keypad is powered by both batteries and an AC

power adaptor model XXX. When the Keypad is operating from

AC power, the display and backlight may operate continuously.

When the Keypad is operating from only battery power, the

display and backlight will only operate while in use (i.e. while

pressing keys and for 20 seconds thereafter).

Installation and Mounting

The Keypad must be used within good communications range of the Security Base. While range varies

with house construction, it is generally sufficient if the Keypad is within 30 to 50 feet of the Base.

The Keypad may be wall mounted or table top mounted. The

Keypad includes 2 AA batteries installed with plastic insulating

tabs. To remove the tabs, first remove the back mounting plate by

lifting on the snap (figure 1).

Pull on the tab for each battery, making sure that the batteries

remain in place. If the batteries must be replaced, follow the marked

battery polarity (figure 2).

For table top placement, re-install the back mounting plate by first inserting the tabs at top of the

mounting plate and then re-snapping the bottom of the mounting plate. Snapping is easier if you

simultaneously lift on the snap while pressing down on the mounting plate. This lifts the snap over the

small detent. Next, snap the table stand onto the back housing. Make sure the table stand is oriented as

shown with the flexible tabs aligned towards the top of the Keypad (figure 3). First insert the top tabs of

Summary of content (5 pages)

PAGE 1
Wireless Keypad SKP2 The SKP2 is a Wireless Keypad with Stay, Away, and Instant arming modes as well as panic emergency mode. The Keypad includes a display and status LED to indicate the current status of the system. The Keypad is powered by both batteries and an AC power adaptor model XXX. When the Keypad is operating from AC power, the display and backlight may operate continuously. When the Keypad is operating from only battery power, the display and backlight will only operate while in use (i.e.
PAGE 2
the table stand into the back housing. Then apply pressure to the bottom tabs until the bottom tabs can be inserted into the bottom housing. For wall mount, first consider whether you plan on using the AC power adaptor. If using the AC power adaptor, next consider how you plan to route the cord. It may be routed through the wall or hang down the wall. (a) If through the wall, the cord must be routed through the opening in the back housing.
PAGE 3
following keys simultaneously on the Keypad “1-3-7-9” for 2 seconds. The Base will respond with audio confirmation and the apps will show a success message. If the Keypad fails to register with the Base, the apps will show a failure message. Possible causes of registration failure include: Keypad not powered, wrong keys pressed, Keypad out of range with Base, or too many Keypads already registered in LifeShield System.
PAGE 4
READY TO ARM NOT READY TO ARM DISARMED ARMED AWAY ARMED STAY ARMED INSTANT EXIT DELAY ENTRY DELAY ***ALARMED*** EXIT ALARM ***PANIC*** INVALID CODE INVALID COMMAND SYSTEM ERROR KEYPAD ERROR PREPARADO NO ESTÁ PREPARADO DESACTIVADO ACTIVADO PARA SALIR ACTIVADO PARA ESTAR ACTIVACIÓN INMEDIATA SALIDA DIFERIDA ENTRADA DIFERIDA ALARMA ERROR DE SALIDA PÁNICO CÓDIGO NO VÁLIDO ORDEN NO VÁLIDA ERROR DEL SISTEMA ERROR DEL TECLADO MESSAGE NOT SENT MENSAJE NO ENVIADO NO RESPONSE RECEIVED LOW BATTERY ENTER CODE SENDING
PAGE 5
FCC Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.