Dongguan Weimei Guanze Technology Co., LTD Bluetooth module VIP-BMS BLE01UserManal Version V 1.
A: Overview VIP-BMSBLE01 is a high-performance, ultra-low-power consumption (Bluetoot Low Energy) radio frequency of Dongguan Weimei Guangze Electronic Technology Co., LTD., with BK Bluetooth 5 SOC BK3432 as the core processor.0 Transceiver system module.This module integrates a high-performance 32-bit M0 MCU kernel to achieve superior stability, following a low-power Bluetooth protocol suitable for single-mode low-power Bluetooth applications. Two: the module technical parameters Power supply range: 2V-3.
: Application areas: Bluetooth remote control door lock Medical care equipment Smart wearable devices smart home Bluetooth electronic weighing weighing A Bluetooth printer device Bluetooth mouse, keyboard, operating lever and other consumer electronics devices Sports and fitness equipment Bluetooth anti-loss device Bluetooth selfie device Bluetooth remote control device Bluetooth tag, beacon A Bluetooth bracelet, a watch Bluetooth wearables Bluetooth blood monitor, blood glucose meter Low power Bluetooth A
Four: instructions Description of the instruction format: Set instruction: eg: FA55 (for fixed header) -06 (instruction code) -03 (data length) Any data that does not start with FA55 is thoroughly transmitted data; Data length: the unit is Byte, the length data is the actual length; Total sum check = instruction code + data length + data value; Set the device name head of instructi contracted on code labour DL Data value Device name FA55 06 length Device name data linear measure Get response data h
V: module size VI: Company information PM & Technical Services: Chen Suhong Tel number: 13530804419 E-mai l : RD02@vip-bms.
FCC Statement FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 PCB Antenna with antenna gain 0dBi We will retain control over the final installation of the modular such that compliance of the end product is assured. In such cases, an operating condition on the limit modular approval for the module must be only approved for use when installed in devices produced by a specific manufacturer.
Upgrade Firmware: The software provided for firmware upgrade will not be capable to affect any RF parameters as certified for the FCC for this module, in order to prevent compliance issues. End product labeling: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains 2A63B-BLE01”.
Compliance list INTEGRATION INSTRUCTIONS for 996369 D03 OEM the and 996369 D03 OEM by Sections 2.2 through 2.10. Requirement 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies.
signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host.
f) Production test procedures for ensuring compliance. The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design.
instructions shall inform the installer that unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. The module manufacturers shall provide a list of acceptable unique connectors. 2.8 Label and compliance information YES Grantees are responsible for the continued compliance of their modules to the FCC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating “Contains FCC ID” with their finished product.
transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
