LED STRIP LIGHT model no. 052-7846-2, 052-7848-8 LED DOUBLE STRIP LIGHT model no. 052-7847-0, 052-7849-6 Toll-free: 1.866.827.
Table of Contents model nos. 052-7847-0, 052-7849-6 | contact us: 1.866.827.4985 model nos. 052-7846-2, 052-7848-8 Preparation 2 Know Your Strip Light 3 Parts List 3 Assembly 4-6 Safety 6 Troubleshooting 7 Linking Feature 8 Care and Maintenance 8 Warranty 9 Preparation Please read and understand this entire manual before attempting to assemble, operate or install the product. Save these instructions so you can refer to them at a later time.
1. Fixture Plate 2. Fixture Lens Cover 1 x1 2 Know Your Strip Light 3 1. Drywall Anchor 2. Mounting Screw 3. Wire Connector 4. Linking Connector 1 x2 3 x3 2 x2 4 x1 NOTE Hardware not shown actual size.
model nos. 052-7847-0, 052-7849-6 | contact us: 1.866.827.4985 model nos. 052-7846-2, 052-7848-8 • With power disconnected to your electrical box, remove the existing fixture. Make a sketch of how the current fixture is wired (by wire color) or mark the wires with masking tape and a pencil so you will know how to properly reconnect the wires to the new LED light fixture. B Assembly A B 1.
AA A 2 1 5. Install a plastic drywall anchor (AA) and a mounting screw (BB) in each drilled mounting hole. A 2 1 Assembly BB 6. Align the 2 mounting keyholes on the fixture plate (A) with the 2 mounting screws in the ceiling. Once both screw heads are through the large ends of the keyholes (position 1), slide the fixture plate to the right until the heads of the screws slide into the narrow ends of the keyholes (position 2). Use a screwdriver to tighten the mounting screws. CC 7.
model nos. 052-7847-0, 052-7849-6 | contact us: 1.866.827.4985 model nos. 052-7846-2, 052-7848-8 A B DD Assembly 9. Snap the fixture lens cover (B) onto the fixture plate (A). Restore power to the electrical box. Turn on the light switch to activate the fixture. 10. Multiple light fixtures can be connected end-to-end, up to the maximum length shown below. Only the first light fixture needs to be hardwired.
Problem The fixture will not light. The fuse blows or circuit breaker trips when the light is turned on. Reason Solution The power is off. Check to ensure the power supply is on. The circuit breaker is off. Check to ensure the circuit breaker is in the on position. There is a bad connection. Check to ensure proper wire connections are made. Contact a qualified electrician. There is a defective switch. Contact a qualified electrician. The wires are crossed or the power wire is grounding out.
Linking Feature model nos. 052-7847-0, 052-7849-6 | contact us: 1.866.827.4985 model nos. 052-7846-2, 052-7848-8 Product Linkability Item # 052-7848-8 – 2 ft. (61 cm.) LED Strip Light Connect up to 30 2 ft. (61 cm.) 1-light strips Item # 052-7846-2 – 4 ft. (1.2 m.) LED Strip Light Connect up to 15 4 ft. (1.2 m.) 1-light strips Item # 052-7849-6 – 2 ft. (61 cm.) LED Double Strip Light Connect up to 15 2 ft. (61 cm.) 2-light strips Item # 052-7847-0 – 4 ft. (1.2 m.
Warranty This product carries a three (3) year warranty against defects in workmanship and materials. Noma Canada agrees to replace a defective product, within the stated warranty period, when returned to the place of purchase with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.
Made in China Imported by Noma Canada, Toronto, Canada M4S 2B8