NOLO 使用说明 Model：CV1 PRO NOLO Instructions 详细使用教程，请访问官网(www.nolovr.com/getstarted/)进行査看。 For detailed instructions, please visit the official website (www.nolovr.
Positioning Base Station *1 Interactive Controller *2 Headset Marker *1 电源适配器 X1 一字型定位器卡座 X1 L 型定位器卡座 X1 Power Adapter *1 Slotted Positioner Socket*1 L-type Positioner Socket*1 一分三充电线 X1 OTG 数据线 X2
1 米数据线 X1 一字型定位器卡座 X1 Three-In-One Charging Cable *1 OTG Data Cable*2 1 m Data Cable*1 Slotted Positioner Socket*1 了解设备 Learn More about the Device 交互手柄 1 扳机键 2 配对键 3 侧按键 4 触控板 5 菜单键 6 指示灯 7 系统/电源键 Interactive Controller 1 Trigger Key 2 Pairing Key 3 Side Keys (Each for the left and right sides) 4 Touch Key 5 Menu Key 6 Indicator Lamp 7 System/ Power Key
定位基站 电源键 配对键 Positioning Base Station Power Key Pairing Key 头盔定位器 指示灯 USB 接口 配对键 Headset Marker Indicator Lamp USB Interface Pairing Key
一. 配合 VR—体机使用说明 I. Instructions for Standalone Headsets 1.搭建网络环境 1. Set up the network environment 将路由器和电脑通过网线连接； 将 VR—体机和电脑连接至同一路由器的 5G Wi-Fi 频段。 Connect the router and the computer with the network cable; Connect the standalone headsets and computer to the 5G Wi-Fi band of the same router. 2.电脑软件准备 2. Software Preparation of PCs 电脑下裁并安装 NOLO HOME Windows 版 (http://download.nolovr.com )。 Download and install the Windows version of NOLO HOME (http://download.nolovr.com). 3.
5.开启 NOLO 设备 将基站放置在与肩同高的水平桌面边缘，并保持基站正面朝 外正对使用者，然后开启基站 和手柄的电源开关。 5. Turn on the NOLO Device Place the base station on the shoulder-height table edge with the front side facing the user, and then turn on the power switches of the base station and controllers. 6. 连接头盔定位器 把 NOLO 附带的头盔定位器底座粘贴在 VR+体机上(注意不要遮挡电源键然后将头盔定位器 插入底座； 使用 OTG 线连接头盔定位器和 VR+体机。 6.
8. 开始游戏 正确佩戴 VR—体机进行标定后，手持 NOLO 手柄，正对基站，开始享受精彩极致的游戏体 验吧！ 注:标定方法请参考-四.NOLO 使用说明 8. Start Game After correctly wearing the standalone headsets to calibrate, take the NOLO controllers, face the base station and start to enjoy the ultimate gaming experience. Notes: Please refer to IV. Instructions for the calibration method. 二. 配合 PC 头显使用说明 II. Instructions for the PC Head-Mounted Display Device 1.连接 PC 头显 使用 PC 头显专用数据线连接 PC 头显。 1.
3.连接头盔定位器 把 NOLO 附带的头盔定位器底座粘贴在 PC 头显上，然后将头盔定位器插入底座； 使用 OTG 线连接头盔定位器和 PC 头显。 3. Connect the Headset Marker Stick the base of the attached headset marker of NOLO to the PC head-mounted display device and then insert the headset marker into the base; Connect the headset marker and the PC head-mounted display device through the OTG cable. 4.开启 NOLO 设备 将基站放置在与肩同高的水平桌面边缘，并保持基站正面朝 外正对使用者，然后开启基站 和手柄的电源开关。 4.
head-mounted display device is searched. 6.开始游戏 正确佩戴 PC 头显进彳 Tfe 定后，手持 NOL◦手柄，正对基站，开始享受精彩极致的游戏体 验吧！ 注:标定方法请参考-四.NOLO 使用说明 6. Start Game After correctly wearing the PC head-mounted display device to calibrate, take the NOLO controllers, face the base station and start to enjoy the ultimate gaming experience. Notes: Please refer to IV. Instructions for the calibration method. 三. 配合安卓手机使用说明 III. Instructions for Android Mobile Phone 注:需同时搭配 VR 眼镜使用。 Note: The VR glasses are needed. 1.
2.电脑软件准备 2. Software Preparation of PC 使用电脑下裁并安装 NOLO HOME Windows 版 (http://download.nolovr.com )。 Download and install the Windows version of NOLO HOME (http://download.nolovr.com). 3.手机端软件准备 使用手机中的应用市场下裁并安装 NOLO HOME 手机版； 运行手机中的 NOLO HOME。 3. Software Preparation of the Standalone Headsets Download and install the NOLO HOME through the application market of the mobile phone; Run the NOLO HOME on the mobile phone. 4.连接头盔定位器 使用 OTG 短线连接手机和头盔定位器，并允许手机上的 USB 权限弹窗。 4.
Stick the base of the attached headset marker of NOLO to the VR Glass and then insert the headset marker into the base; Place the mobile phone into the VR Glass and fix it. 6.开启 NOLO 设备 将基站放置在高度适当的桌面上，并保持基站正面朝外正对使用者，然后开启基站和手柄的 电源开关。 6. Turn on the NOLO Device Place the base station on the shoulder-height table edge with the front side facing the user, and then turn on the power switches of the base station and controllers. 7.建立 PC 连接 运行电脑上和手机中的 NOLO HOME; 保持手机中的 NOLO HOME 为等待连接状态，待电脑自动扫 描到手机后，点击连接按纽。 7.
验。 注:标定方法请参考-四.NOL◦使用说明 8. Start Game After correctly wearing the mobile phone and the VR Glass to calibrate, take the NOLO controllers, face the base station and start to enjoy the ultimate gaming experience. Notes: Please refer to IV. Instructions for the calibration method. 四. NOLO 使用说明 IV. NOLO Instructions 定位基站摆放要求 1.建议将基站摆放在与肩同高的位置； 2.确保基站位于水平桌面的边缘； 3.确保基站正面朝向使用者(带有 NOLO 标识的为正面)。 Placement Requirements for the Positioning Base Station 1.
标定正方向方法 The Positive Direction Calibration Method 1. 双臂前伸，双手并拢，目视前方； 2. 保证基站、手柄、头盔定位器在一条直线上； 3. 分别双击两个手柄上的电源键完成正方向标定。 1. Keep your arms forward and your hands together with your eyes to the front; 2. Keep the base station, controllers and the headset marker at the same straight line; 3. Click the power key of the two controllers twice respectively to complete the calibration of the positive direction.
2. Slightly press the Pairing Key on the headset marker to complete the height calibration. 定位问题处理 1.同一定位范围内，无多套 NOLO 交互设备同时使用，如果必须开启多套 NOLO 设备，请 按照下图摆设 NOLO 的定位基站，避免多个基站互相干扰。 2.同一环境下,无其他红外激光设备干扰如 HTC VIVE、主动式红外摄像头等,无其他超声波 发射设备干扰。如有以上设备请关闭干扰设备再使用，或更换使用环境。 3.尽量避免环境内有镜面等反射平面的存在。如果在类似环境发现设备定位抖动情况，需更 换环境使用。 4.使用过程中切勿背对基站或遮挡手柄、头盔定位器，以上情况会导致定位丢失，如遇以上 情况请正对基站标定正方向。 5.如遇无线干扰，导致设备定位卡顿，需重新配对处理，请参考配对说明。 Positioning Problem Processing 1.
2.长按定位基站配对键(如图所示)，进入配对模式，定位基站指示灯呈绿色闪烁状态。 2. Long press the Pairing Key of the positioning base station (as shown) to enter the pairing mode with the indicator lamp shining in green. 3.分别长按两支交互手柄的配对键(如图所示），直至手柄震动。每次配对过程中每支交互手 柄只需配对一次，请不要重复配对。 3. Respectively long press the Pairing Key of the two interactive controllers (as shown) till the controller vibrates. During each pairing process, each controller can only be paired once. Please do not re-pair. 4.长按头盔定位器的配对键，直至头盔定位器指示灯红色 LED 闪烁一次。 4.
5. Click the Pairing Key of the positioning base station to end the pairing mode. If the LED indicator lamp of two controllers and the headset marker turn to green after 3 to 5 seconds, then the pairing succeeds; if turn to red, then the pairing fails and please re-pair.
Red and Green Flashing Alternately Hardware Error Green Flashing Pairing Green Fully Charged/ Normal Operation Red Flashing Low Power Red (The Interactive Controllers and Headset Marker) Waiting for the End of Pairing/ Unpaired Red (The Base Station) Improperly Placed/ Abnormal Operation 五、安全信息 V.
7.请按当地规定处理本设备、电池及其他附件，不可将他们作为生活垃圾处理。若电池处置 不当可能导致电池爆炸。 7. Please dispose this device, battery and its accessories according to local regulations, but not as the domestic garbage. The improper disposal may cause the battery’s explosion. 8.使用未经认可或不兼容的电源、充电器或电池，可能引发火灾、爆炸或其他危险。 8. The use of unapproved or incompatible power, charger or battery may cause fire, explosion or other dangers. 9.只能使用设备制造商认可其与此型号设备配套的配件。如果使用其他类型配件，可能违反 本设备保修条款及本设备所处国家的相关规定，并可能导致安全事故。如需获取认可配件， 请与授权服务中心联系。 9.
Complete accessories (Excluding the headset marker buckles); No private disassembly or modification. 15 天内包换：凡购买本公司 NOL◦产品,如遇产品出现非人为原因导致的性能故障，可在 15 天内申请免费换新，申请通过后请将问题产品寄回指定地址，新产品将在收到问题产品后 为 您寄出；若经检测后，发现产品硬件没问题，则不予换新。 Guarantee for replacement within 15 days: All purchased NOLO products of the company with performance fault caused by non-artificial reason can apply for a free replacement within 15 days.
•由于使用者或第三者的疏忽、过失、滥用、误用或灾祸等原因造成产品损坏的,如摔坏、外 表刮痕、划伤、进水、输入不当电压、机械破坏、高温、产品烧毁或与不适当的设备、装置、 软件、服务或其他未授权第三方物件一起使用等； •用户发回返修途中由于运输、装卸等造成的损坏(若是我司寄回途中导致的损坏，则由我司 负责)； •产品因不可抗拒的自然因素造成的损坏,如地展、火灾、雷 击等； •非 NOLO 官方生产的假冒伪劣品； •使用本产品时，由于违反当地法律导致产品出现故障； •进行沟通和查找原因时，故意隐瞒事实真相者； •无法提供相关购买凭证或包装侧面条形码被涂改、斯毁或遗失； •超过三包有效期； •其他三方配件及赠品均不包括在保养服务内。 • The product failures or damages caused by incorrect or improper operations; • The product damages caused by using non-original or failing to use, maintain, upkeep according to the instructions
• The company reserves the final right to interpret the above after-sales service policies to the extent permitted by law. 若有变更，以本公司新制定的有关规定或国家更新的相关法律法规为准。 If there are any changes, the new relevant regulations of the company or the updated relevant laws and regulations by the state will prevail. 七. 有害物质声明 VII.
会另行标示(例如，电池单元模块会有另一个标示贴在其产品上)。此环保使用期限只适用于 手册中规定的使用中所规定的条件下工作。 This symbol also refers to the environmental protection use period of the product and its accessories. It will be indicated separately if different environmental protection use period is applicable to some parts (For example, a different label is pasted on the battery unit module). The environmental protection use period is only applicable to the prescribed operating environment in the Instructions.
Name Contact E-mail Address Postcode Product Model Contact Device SN No. 关注 NOLO VR 官方微信 联系 NOLO VR 客服 了解更多信息，请访问：www.nolovr.com Follow NOLO VR Official WeChat Contact NOLOVR Customer Service For more information, please visit www.nolovr.com.
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
