EN USER INSTRUCTIONS AND SAFETY Firmware Version: 4.
Congratulations on your purchase of an N-Com product. N-Com B5 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about B5, and to download high-definition instructions as well as the latest Firmware version, visit the website www.n-com.
Contents WARNINGS AND SAFETY ............................................................. 4 1.1.Road safety............................................................................. 4 1.2.Switching on the system in safe environments..................................... 4 1.3.Interferences ........................................................................... 4 1.4.Appropriate use........................................................................ 4 1.5.Qualified personnel.......................
1. WARNINGS AND SAFETY Read this User Manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like. Caution: Installation of the N-Com B5 system results in a weight increase of approximately 107g, which is added to the weight of the helmet and of the other accessories.
B5 Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before you use the system on the road. Caution: Adjusting the volume to very high levels may cause damage to your hearing. Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it so as to avoid audio reproduction at high volumes. Constant exposure to high audio volumes may damage your hearing.
1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: 2. The presence of a crossed-out wheelie bin indicates that in the European Union the product is subject to separate collection at the end of its useful life. Do not dispose of these products together with undifferentiated urban waste.
B5 3. INSTALLATION Important: Prior to installing the N-Com system, it is recommended to write down the identification code affixed to the product (see chapter 17.5). You can download the installation video from www.n-com.it N-Com / Download section. Before you install the B5 system on the helmet, make sure it turns on properly. Press the “on” key for about 2 seconds, until the LED lights up and you hear a beep in the headset. Proceed with the installation.
Option 1 Option 2 N.B.: Keep the filling material in case you wish to use the helmet without the N-Com system in the future. Place the system in the special housing in the back of the helmet, pushing it all the way into the groove (Fig. 3). Fig. 3 Fold the antenna back inside the shell. Fig. 4 8 Fix the cable inside the helmet and make sure the right fixing clip snaps into its housing (Fig.
B5 Position the microphone in the housing on the left of the helmet, inserting the metal boom in the groove found in the chin guard coupling frame (Fig. 5). Caution: make sure that the side of the microphone support with the writing “NCom” is facing inward. Fig. 5 Fix the cable inside the helmet and make sure the left fixing clip snaps into its housing. Hook up the keypad to the helmet by clicking in the relevant hooks. Fig.
3.1. Removing the B5 system from the helmet Proceed as follows to remove the B5 system from the helmet: Remove the cheek padding and the shell gasket; Remove the keypad from the shell, using a flat head screwdriver (or a similar tool) to lever upwards in the special hollow as shown in fig. 7. Fig. 7 Unhook the right and left clips from the shell, levering upward using a flat head screw (or a similar tool), as shown in figure 8. Fig. 8 Fig.
B5 4. BASIC FUNCTIONS System ON System OFF Increase Volume Decrease Volume 4.1. Press “on” and keep it pressed for about 2 seconds, until the LEDs turn on and you hear a beep in the headset. Press “on” and keep it pressed for about 6 seconds, until the LEDs turn off and you hear a beep in the headset. Briefly press “” to increase the volume. A double tone signals the highest volume level. Briefly press “” to decrease the volume. A double tone signals the lowest volume level.
5. MOBILE PHONE Answering a phone call Briefly press any key when you hear the incoming call signal. Voice call Press “on” and keep it pressed for about 2 seconds. Redial last number Press “on” and “n” at the same time. Dial Friend Number Press “n” and keep it pressed for about 2 seconds. Hanging up/rejecting a phone call Transferring a call from helmet to mobile phone Press “on” and keep it pressed for about 2 seconds.
B5 6. MUSIC VIA BLUETOOTH – A2DP BLUETOOTH PROTOCOLL Play music (Play) Briefly press “on”. Pause function (Pause) When the player is connected and playing music, briefly press “on”. Next track (Skip) When the player is playing music, press “” for 2 about seconds. Previous track (Rew) When the player is playing music, press “” for 2 about seconds. Turning off the A2DP Press “on” and keep it pressed for about 4 seconds.
8.1. Navigators on Smartphone (Smart Navi System) By connecting the B5 system to a Smartphone, all navigator instructions are sent to the helmet through the A2DP profile. During each navigator communication, the intercom via Bluetooth is automatically cut off and subsequently restored when the navigator has stopped giving road instructions (SMART NAVI SYSTEM function). The Smart Navi System function can be turned off in Setting Mode (see Chapter 15). 9.
B5 12. BIKE TO BIKE INTERCOM The N-Com system is used for bike-to-bike communication up to a distance of about 500 m (open terrain, no obstacles). The B5 system entails the use of a default “STANDARD” commands configuration, or the use of a “FRIENDS” configuration that can be turned on from the N-Com Wizard or dedicated App.
12.2. Bike to bike intercom function How the Bike-to-Bike call works (Standard Configuration) Connection CHANNEL 1 Briefly press “n”. Call CHANNEL 2 Press the “n” key twice. Call CHANNEL 3 Press the “n” key three times. Disconnection of active intercom Briefly press “n”. Con FRIENDS CONFIGURATION active: Call CHANNEL 4 Briefly press “on”. Call CHANNEL 5 Press the “on” key twice. Call CHANNEL 6 Press the “on” key three times. Disconnection of active intercom Briefly press “on”. N.B.
B5 13. “UNIVERSAL INTERCOM” INTERCOM The N-Com B5 system can be connected via Bluetooth to intercom systems of other brands, thanks to the UNIVERSAL INTERCOM function. 13.1. Pairing up the UNIVERSAL INTERCOM The N-Com system can be paired up to an intercom of a different brand (from now on referred to as Intercom B) as if it was a mobile phone. 1. 2. 3. 4. 5. 13.2.
14. SETTING MODE All Bluetooth pair ups and other adjustments are carried out in this mode. To put the system in Setting mode, press the “on” key and keep it pressed for 4 seconds, until the red LED starts to flash quickly. n on N + on ▲ Turning on/off the RDS ▲ + ▼ x1 Turning on/off the Smart Navi System Pairing up Secondary Phone Pairing up CHANNEL 1 Pairing up CHANNEL 2 Pairing up CHANNEL 3 Pairing up CHANNEL 4 Pairing up CHANNEL 5 Pairing up CHANNEL 6 Reset *With Friends Configuration active.
16.
Radio Menu Button n on Turning on the Radio x2 Turning off the Radio x2 N + on Automatic search for new station Change station (pre-set stations) + 2 sec 2 sec Pre-set station 4 sec Pairing up mode (system turned off) Setting* Turning on/off the RDS X Turning on/off the Smart Navi System Pairing up secondary mobile phone (or device) 2 sec 2 sec Pairing up CHANNEL 1 X Pairing up CHANNEL 2 x2 Pairing up CHANNEL 3 x3 Pairing up CHANNEL 4 X Pairing up CHANNEL 5 x2 Pairing
B5 17. LIMITED WARRANTY With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: - Read the cautions pertaining to safety and proper use. - Read the warranty terms and conditions. - Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the product has to be taken back to the dealer where it was purchased. 17.1.
17.3. Validity of this limited warranty This warranty is valid only if the enclosed warranty form is duly and completely filled out with the following information: Product identification code Name and stamp of the authorized dealer. Product purchase date. Buyer’s name and address. Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the product from the dealer. 17.4.
18.
www.n-com.