Firmware Version: 3.1x EN USER INSTRUCTIONS AND SAFETY v.
Congratulations on your purchase of an N-Com product. N-Com B1 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about B1, and to download highdefinition instructions as well as the latest Firmware version, visit the website www.n-com.
B1 Contents 1. WARNINGS AND SAFETY ...................................................... 4 1.1.Road safety.......................................................................... 4 1.2.Switching on the system in safe environments ........................... 4 1.3.Interferences ....................................................................... 4 1.4.Appropriate use .................................................................... 4 1.5.Qualified personnel ..........................................
1. WARNINGS AND SAFETY Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N-Com B1. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like.
B1 Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before you use the system on the road. Caution: Adjusting the volume to very high levels may cause damage to your hearing. Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it so as to avoid audio reproduction at high volumes. Constant exposure to high audio volumes may damage your hearing.
1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: The presence of a crossed-out wheelie bin indicates that in the European Union the product is subject to separate collection at the end of its useful life (European Directive 2002/96/EC).
B1 3. INSTALLATION The B1 system can be installed on Nolan helmets preset for the N-Com B1 system. Visit the website www.n-com.it for a list of compatible models. Open the small door on the e-box and place the rechargeable battery inside the system, making sure it is inserted in the right direction (Fig.1) Thread the keypad flex cable into the plastic clip, as shown in Fig. 2 Thread the keypad flex cable into the connector, making sure that it is all the way in. Fig.
Fig. 4 Fig. 5 Remove the protective film from the adhesive on the Ferma-flex clip (Fig. 4) Position the plastic Ferma-flex clip as shown in figure 5 Before you install the B1 system on the helmet, make sure it turns on properly. Press the “on” key for about 2 seconds, until the LED lights up and you hear a beep in the headset. Proceed with the installation. Remove the cheek padding (see helmet instructions). Remove the helmet edge gasket using the special tool (Fig. 6).
B1 Place the system in the special housing in the back of the helmet, pushing it all the way into the groove (Fig. 8). Fix the cable inside the helmet and make sure the right fixing clip snaps into its housing (Fig. 9) Position the microphone in the housing on the left of the helmet, inserting the metal boom in the groove found in the chin guard coupling frame (Fig. 10). Fig. 8 Fig. 9 Caution: make sure that the side of the microphone support with the writing “NCom” is facing inward. Fig.
3.1. Fix the cable inside the helmet and make sure the left fixing clip snaps into its housing. Hook up the keypad to the helmet by clicking in the relevant hooks. Fig. 11 Position the left and right speakers in the respective housing obtained in the polystyrene cheek padding. If necessary, rotate the speakers slightly in their housing. Reassemble the gasket and secure it with the specific screw Reassemble the cheek padding.
B1 4. SYSTEM CHARACTERISTICS N-Com B1 allows wireless connection to a mobile phone, a satellite navigator, and an MP3 A2DP player using Bluetooth technology. The system can also be used for wireless intercom communication between two helmets, if both helmets are equipped with a N-Com Bluetooth system. The system can be expanded by means of a USB Multimedia Wire accessory (sold separately), which is used for cable connection to multimedia sources.
2. 3. 4. 5. 6. 7. Press “on” and keep it pressed (for more than 6 seconds), until the LEDs start to flash quickly and you hear a sharp beep in the headset, indicating the “Pair-up mode”; On the Bluetooth device, turn on the search for Bluetooth devices (refer to the instructions manual of your device for the proper pairing up procedure, as it varies depending on the brand and model of the device); After a few seconds, the device will display the name “N-Com B1 v.X.
B1 Conference call function B1 allows a conference call with Rider and Pillion Passenger. When a call comes in on a mobile phone connected via Bluetooth to B1, the Rider-Pillion Passenger intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call (by briefly pressing “on”).
9. AUDIO DEVICES WITH CABLE CONNECTION N-Com B1 allows connection via cable (sold separately) to audio sources equipped with the 3.5mm output generally used by these devices for the headsets. To listen to the audio source, connect the cable to the helmet using the micro-USB port, then start playing the audio file on the device, then activate the audio peripheral device using the specific key. You can turn on or off listening in the helmet by pressing the “” key for 2 seconds. N.B.
B1 11. BATTERY Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely. 11.1. Battery discharged signal When turned on, the system signals when the battery is running down by switching to the “Reserve” mode.
12.
B1 13. LIMITED WARRANTY With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: - Read the cautions pertaining to safety and proper use. - Read the warranty terms and conditions. - Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the product has to be taken back to the dealer where it was purchased. 13.1.
Name and stamp of the authorized dealer. Product purchase date. Buyer’s name and address. Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the product from the dealer. 13.4.
14.
B1v04 - 28/09/2012 14.35.