Firmware Version: 1.
Congratulations on your purchase of an N-Com product. N-Com B1 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about B1, and to download highdefinition instructions as well as the latest Firmware version, visit the website www.n-com.
B1 Contents 1. WARNINGS AND SAFETY ........................................................ 4 1.1.Road safety ........................................................................... 4 1.2.Switching on the system in safe environments............................ 4 1.3.Interferences ......................................................................... 4 1.4.Appropriate use ..................................................................... 4 1.5.Qualified personnel....................................
B1 1. WARNINGS AND SAFETY Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N-Com B1. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like.
B1 Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before you use the system on the road. Caution: Adjusting the volume to very high levels may cause damage to your hearing. Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it so as to avoid audio reproduction at high volumes. Constant exposure to high audio volumes may damage your hearing.
1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: The presence of a crossed-out wheelie bin indicates that in the European Union the product is subject to separate collection at the end of its useful life (European Directive 2002/96/EC). Do not dispose of these products together with undifferentiated urban waste.
B1 3. INSTALLATION Fig. 1 Fig. 2 Remove the N-Com protection plate located on the helmet shell (Fig. 1) and open the helmet chin guard (flip up helmets). Remove the right and left cheek pads from the helmet (see specific instructions provided in the user manual of the helmet). Fig. 3 Fig. 4 Remove the Noise Reducers from the two cheek pads, and tear off the precut plastic (if equipped). Fig. 5 Remove the back of the comfort padding by pulling on the neck roll until it separates from the shell (Fig.
ONLY FOR FULL- FACE HELMETS Remove the chin guard by pulling on the special red tab. Fig. 7 Remove the right and left polystyrene cheek pads by gently pulling them out of the helmet. The helmet shell can be opened slightly to facilitate the removal of the cheek pad . Caution: In case the polystyrene cheek pad is damaged during this operation, turn to your local dealer for its replacement. Fig.
B1 3.1. Installing the microphone JET HELMETS OR FLIP- UP HELMETS Fig. 9 Fig. 10 Prepare the microphone by inserting the microphone clamp, being careful to position it properly (Fig. 9) Fig. 11 Note: the flat part of the clamp must be facing upward when the microphone is positioned as shown in figure 11. Position the microphone in its support as shown in figure 10, being careful that the fluorescent clamp is facing toward the inside of the helmet.
3.2. Connecting the battery Only for Jet helmets or flip- up helmets: Fig. 15 Fig. 16 Hook up the battery cable (Red+Black) to the connector located on the wiring system (Fig. 15). Insert the battery in its holder, first positioning the side equipped with the cables outlet, keeping the cables underneath the plastic tab (Fig. 16). Fig. 17 Fig. 18 Insert the connectors set in the cable-stop guide located on the side of the batteryholder (Fig. 17 and 18).
B1 3.3. Installing the system on the helmet Fig. 20 Position the system inside the helmet as shown in figure 20, next to the N-Com housing in the shell. Looking at the helmet from the outside, slide the rear positioning tab into groove A as shown in the figure; Press in the area marked PUSH from inside the helmet until the fastening clasp B clicks (Fig. 21). Fig. 21 Pull out the connectors area from the helmet gasket: the gasket will have to be slightly deformed to facilitate the insertion. Fig.
Fig. 23 Fig. 24 Insert the microphone connector in the micro USB electronic plate. Before you place the speaker in its housing, apply the Velcro pad to the polystyrene cheek pad (Fig. 24). Position the loudspeaker in the special housing obtained in the polystyrene cheek pad (Fig. 25). Fig. 25 Replace the polystyrene cheek pad (left side), positioning the cable in the groove that you see in the cheek pad (Fig. 25).
B1 Only for Jet helmets or flip- up helmets Secure the battery-holder support to the right side of the helmet, lining up the holes with the pins on the shell (Fig. 27) Fig. 27 Before you place the speaker in its housing, apply the Velcro pad to the polystyrene cheek pad (right side). Position the loudspeaker in its housing obtained in the polystyrene cheek pad (right side). Replace the polystyrene cheek pad (right side), positioning the cable in the groove you see in the cheek pad.
Position both the comfort cheek pads in their housing (see specific instructions provided in the helmet user manual) making sure that all the press-studs click. Note : Carefully check the proper final positioning of the cheek pad, pulling the chinstrap toward the inside of the helmet and testing the press-studs. Caution: Make sure that there are no cables sticking out of the helmet and that the loudspeakers are in their housing.
B1 5.1. Basic functions All N-Com system functions are available through the operation of three pushbuttons: , on and . Every time the system is given a command, a special acoustic signal can be heard, which varies depending on the function being requested. This way, all the functions can be used while wearing the helmet. The type of command given to the system depends on how long the pushbutton is pressed. System ON System OFF Increase Volume Decrease Volume 5.2.
Note: If a Bluetooth device (mobile phone or GPS) equipped with music player with Bluetooth A2DP player has already been paired up, the pairing up DOES NOT have to be repeated as the A2DP protocol has already been stored in the B1. Once the Bluetooth device has been paired up, connection is automatic when the system is turned on. 6.1. Affiliation reset function You can remove all affiliated devices from the system memory.
B1 Note: If the navigator is pre-set for connection to a Bluetooth mobile phone, you will be able to receive the phone call audio directly in the helmet through the GPS. In this case, you can answer the call directly from the navigator. GPS Conference Call Function The Conference function allows you to keep the Rider-Pillion Passenger intercom open even while the satellite navigator is giving instructions, thus preventing the intercom mode to be turned off every time the navigator gives instructions.
11. RIDER- PASSENGER INTERCOM MODE In order to use B1 in wireless intercom mode, both helmets have to be equipped with a NCom Bluetooth system. In order for two N-Com systems to communicate with one another, they have to be paired up first. 11.1. Intercom affiliation 1. Make sure both N-Com Bluetooth systems are turned off; 2. Set both N-Com Bluetooth systems in Pairing up mode by pressing on (for more than 4 seconds), until the LEDS start to flash quickly; 3.
B1 12. BATTERY Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely. 12.1. Battery discharged signal When turned on, the system signals when the battery is running down by switching to the Reserve mode.
13.
B1 14. LIMITED WARRANTY With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: - Read the cautions pertaining to safety and proper use. - Read the warranty terms and conditions. - Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the product has to be taken back to the dealer where it was purchased. 14.1.
Name and stamp of the authorized dealer. Product purchase date. Buyer s name and address. Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the product from the dealer. 14.4.
15.
B1 - 16/10/2012 9.28.
