EN USER INSTRUCTIONS AND SAFETY
Congratulations on your purchase of an N-Com product. N-Com Bluetooth Kit3 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about Bluetooth Kit3, and to download high-definition instructions as well as the latest Firmware version, visit the website www.n-com.
Contents 1. WARNINGS AND SAFETY _______ 5 1.1.Reference standards _________ 5 1.2.Road safety ________________ 5 1.3.Switching on the system in safe environments____________________ 6 1.4.Interferences _______________ 6 1.5.Appropriate use _____________ 6 1.6.Qualified personnel __________ 7 1.7.Accessories and batteries______ 7 1.8.Disposal ___________________ 8 2. CONTENT OF THE PACKAGING __ 9 3. INSTALLATION _____________ 10 4. SYSTEM CHARACTERISTICS ___ 11 4.1.Basic functions _____________ 12 4.2.
FOR USA MARKET ONLY: SPECIAL WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
1. WARNINGS AND SAFETY Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N-Com Bluetooth kit3. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like.
• • • • • • 1.3. • • • • 1.4. Set your cell phone on automatic answer (see the cell phone instructions to do this). If your cell phone is not equipped with this function, first stop your vehicle in a safe area, in compliance with Traffic Regulations and then answer the call. Do not make any calls while riding. Stop your vehicle in a safe place in compliance with Traffic Regulations, and then make the call.
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before you use the system on the road. Caution: Adjusting the volume to very high levels may cause damage to your hearing. Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it so as to avoid audio reproduction at high volumes. Constant exposure to high audio volumes may damage your hearing.
• • Contact your local dealer to see about the availability of approved accessories. When disconnecting the power supply cable of any accessory or of the battery charger, always grab and pull the plug not the cable. Do not use batteries for purposes other than the prescribed ones. Never use batteries or battery chargers that turn out to be damaged. Do not short-circuit the battery. Keep the battery at a temperature between 10°C and 35°C.
2.
3. INSTALLATION Bluetooth Kit3 can be installed on all Nolan helmets pre-set for the N-Com system. In order to use the N-Com Bluetooth Kit3 system, the Nolan helmet must be equipped with the Basic Kit2 (or Basic Kit), sold separately. Note: Before using the N-Com Bluetooth Kit3 system, the battery must be installed and recharged (see instructions for Basic Kit). • Install the Basic Kit2 (or Basic Kit) on the helmet, according to the specific instructions. Fig. 1 Fig. 2 • • • Fig.
Position the e-box in the relevant housing. First insert the front part, then press down on the e-box until both hooks fully click. To remove the e-box, press the two sliding hooks at the same time until the e-box comes out. Warning: Do not leave the helmet exposed to atmospheric agents without the e-box or the protection plate provided with the helmet. 4.
4.1. Basic functions All N-Com system functions are available through the operation of three pushbuttons: “ ”, “on” and “ ”. Every time the system is given a command, a special acoustic signal can be heard, which varies depending on the function being requested. This way, all the functions can be used while wearing the helmet. The type of command given to the system depends on how long the pushbutton is pressed. System ON System OFF Increase Volume Decrease Volume 4.2.
Menu Base Radio A2DP Functions • • • • • • • • Management of an external source connected via cable Use of Mobile phone/GPS with Bluetooth connection Use of the intercom (“Rider–Pillion Passenger” or “Bike-to-Bike”) Listening to and management of FM Radio Use of Mobile phone/GPS with Bluetooth connection Use of the intercom (“Rider–Pillion Passenger” or “Bike-to-Bike”) Listening to and management of Bluetooth A2DP player Use of Mobile phone/GPS with Bluetooth connection Functions concerning Bluetooth m
5. PAIRING UP BLUETOOTH DEVICES In order for the Bluetooth Kit3 system to be connected to another Bluetooth device, the latter needs to be first paired up with the N-Com system. The pairing up procedure is the same for all Bluetooth devices: mobile phones, MP3 Bluetooth players, satellite navigators, etc. 1. Make sure the Bluetooth Kit3 is turned off; 2.
Connection Disconnection Briefly press “ ” and “ ” at the same time, releasing them right away. Press “ ” and “ ” at the same time and keep them pressed for 4 seconds. Note: Connection to the Mp3 Bluetooth player is automatic by positioning the system on the relevant menu position. 5.1. Affiliation reset function You can remove all affiliated devices from the system memory.
Voice call (if equipped) Redial last number Transferring a call from helmet to mobile phone Briefly press “ ” and “ ” at the same time, releasing them right away Press “ ” and “ ” at the same time and keep them pressed for 2 seconds (until you hear the acoustic signal) To transfer an ongoing call from the helmet to the mobile phone, press both “ ” and “ ” at the same time and keep them pressed for 4 seconds Conference call function Bluetooth Kit3 allows a conference call with Rider and Pillion Passenger.
Note: If the navigator is pre-set for connection to a Bluetooth mobile phone, you will be able to receive the phone call audio directly in the helmet through the GPS. In this case, you can answer the call directly from the navigator. GPS Conference Call Function The Conference function allows you to keep the “Rider-Pillion Passenger” intercom open even while the satellite navigator is giving instructions, thus preventing the intercom mode to be turned off every time the navigator gives instructions.
Turning on the radio Turning off the radio New station automatic search Pre-setting a radio station The radio turns on automatically by selecting the “Radio” menu (scroll through the menu by pressing “on” for 2 seconds). The radio turns off when you change the menu item (scroll through the menu by pressing “on” for 2 seconds) Press “ ” and keep it pressed for 2 seconds Press “ ” and keep it pressed for 4 seconds. This function can also be turned on through PC using the “N-Com Wizard” programme.
Play music (Play) Pause function (Pause) Next track (Skip) Stop playing music (Stop) Press the “ ” button and keep it pressed for 2 seconds. When the player is connected and playing music, press “ ” for 2 seconds. When the player is playing music, press “ ” for 4 about seconds. Press “ ” for 2 seconds. The music stops and the A2DP player is disconnected. By moving to another function with the menu key, the system automatically disconnects the A2DP device.
Once it is turned on, cable connection stays active even in the subsequent menus. Consequently, you can hear the device connected via cable even while listening to music via A2DP or via RADIO. The Bluetooth Kit3 can be connected with cables of the N-Com range of both the Mono type (Multimedia Wire or Mobile Wire) and Stereo type (Multimedia Wire2). Bluetooth Kit3 is pre-set to receive Stereo cables. In order to use a Mono cable, a pre-selection needs to be carried out.
4. 5. 11.2. 3b. Bike-to-Bike pair up: On one of the two helmets, press “on” for at least 2 seconds; After a few seconds, the helmets “recognize” each another, a beep is emitted to signal the pair up was successful and intercom communication is activated; Turn off both Bluetooth Kits and turn them back on to store the pair up data. Intercom function After carrying out the proper pair up procedure, turn on the two helmets.
• The audio coming from an external source (connected via cable or Bluetooth) IS NOT shared with the helmet connected in Bike-to-Bike Intercom mode. • The audio coming from the radio IS NOT shared with the helmet connected in Bike-to-Bike Intercom mode.
13. BATTERY Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely. 13.1. 1) Connect the battery charger to the mains. 2) Plug in the battery charger connector in the corresponding connector on the helmet.
14.
Button Radio menu A2DP menu Base Menu Intercom Pressure on on Brief Long Brief Long Brief Long Brief Long Activate intercom X Deactivate intercom X Intercom swap (from Bike-to-Bike to Rider-Pillion Passenger)* X X Activate audio device Deactivate audio device X (2s) Play music (Play) X (2s) X (2s) X (4s) Pause Function (Pause) Next track (Forward) Automatic search for new station Change station (preset stations) Pre-set station X (2s) X (2s) X (2s) X (4s)
Button Setting Pressure Pairing up mode system turned off Pilot-Passenger intercom pair up Bike-to-Bike intercom pair up** Operation with Mono/Stereo Cable** Operation with only one loudspeaker** Erase pair ups** on on Brief Long Brief Long Brief Long Brief Long X (4s) X X (2s) **With N-Com system in Pairing up Mode 26 X (2s) X (2s) X (2s)
15. LIMITED WARRANTY With this LIMITED WARRANTY CERTIFICATE, Nolan® warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: - Read the cautions pertaining to safety and proper use. - Read the warranty terms and conditions. - Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the product has to be taken back to the dealer where it was purchased. 15.1.
This warranty does not include those parts subject to wear and tear such as, for example, the rechargeable battery and the cables used for connection between the various N-Com systems or between the N-Com systems and other devices. Since Nolan® does not supply the system on which the cell phones work, it shall not be responsible for the operation, availability, coverage, services or range pertaining to the aforementioned system.
AFTER 2 (TWO) YEARS FROM THE DATE OF PURCHASE, THIS LIMITED WARRANTY IS VOID FOR ALL EFFECTS AND PURPOSES. Repairs or maintenance under warranty do not extend the period of the warranty itself. Therefore, in case the product or one of its components is replaced, this does not initiate a new warranty period, as the purchase date of the original product shall be taken into account for warranty purposes.
15.5. Product identification N-Com products are identified by means of a code that allows product traceability and identification. The identification code is found underneath the bar code printed on the product packaging. - FOR USA AND CANADA MARKET ONLY - Dear Customer, Thank you for choosing a Nolan® N-com™ device. PLEASE READ CAREFULLY ALL THE CLAUSES AND CONDITIONS OF THIS LIMITED WARRANTY CERTIFICATE.
This warranty covers only material and manufacturing defects.
PROCEDURE TO BE FOLLOWED TO MAKE POSSIBLE CLAIMS To proceed with any claim covered by this warranty, the purchaser must notify directly Nolan’s agent in the USA of the alleged defect encountered by him. In agreement with Nolan’s agent, the purchaser may have to return the device to which complains refer, at the purchaser’s expense, along with the sales receipt or other proof of purchase (and date of purchase) and a copy of the warranty registration form.
16.
Bluetooth Kit3 - 19/01/2011 8.54.