B901 EN USER INSTRUCTIONS AND SAFETY Congratulations on your purchase of an N-Com product. N-Com B901 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. For additional information about B901, and to download high-definition instructions as well as the latest Firmware version, visit the website www.n-com.it Firmware Version: 1.
Model: B901 K
Contents 1. WARNINGS AND SAFETY ................................................................................................................... 4 1.1.Road safety .................................................................................................................................................................................................4 1.2.Switching on the system in safe environments .....................................................................................................
EN 1. WARNINGS AND SAFETY Read this User Manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like. Caution: Installation of the N-Com B901 system results in a weight increase of approximately 110g, which is added to the weight of the helmet and of the other accessories.
B901 Caution: An incorrect installation of the system in the helmet may alter the aerodynamic and safety characteristics of the helmet itself, thus creating dangerous conditions. Install the N-Com system according to the instructions provided in the product documentation. In case of doubt, please contact your local N-Com dealer. Warning: Listening to other equipment should not interfere with driving the vehicle, which must be the top priority at all times.
EN 2.
B901 3. INSTALLATION ON THE HELMET Important: Prior to installing the N-Com system, it is recommended to write down the identification code affixed to the product (see chapter 19.5). You can download the installation video from www.n-com.it X-Series Download section. 3.1. Preliminary operations – Jet helmets or Flip-up helmets Open the helmet chin guard (only on Flip-up helmets). Pull out both comfort cheek pads, left and right, from the helmet. (Fig.
EN Fig. 4 Fig. 5 Fig. 6a Fig. 7 Fig. 6b ONLY FOR X701 – X603 - X602 HELMETS: Take the polystyrene cheek pads that have just been removed and, using a pair of scissors, remove the round insert by cutting the fabric securing points. (Fig. 8) Keep the foam used to cover the speakers housing in case you wish to use the helmet without the Bluetooth Kit system. Fig. 8 Fig. 9 helmets X702GT - X701 – X603 Fig.
B901 3.3. Installing the microphone – jet helmets or flip-up helmets Set up the microphone by inserting the clip that holds it in place, being careful to position it correctly. (Fig. 11) Note: The flat part of the clip has to face upward when the microphone is positioned as shown in Fig. 11. Fig. 11 Fig. 12a Position the microphone on the left side of the helmet, screwing the screw into the small frame. (Fig.12 a/b) Make sure that the fluorescent band is facing the inside of the helmet.
EN 3.5. Installing the battery and the right-hand side speaker Connect the battery to the wiring system. (Fig. 16) Position the battery in the right polystyrene cheek pad housing and secure it using the Velcro ribbon. (Fig. 17 / 18) Fig. 16 Fig. 17 Fig. 18 Position the right-hand side speaker in the specific cheek pad housing and secure it using the specific adhesive (Fig. 19). Reposition the right polystyrene cheek pad in its housing. Fig.
B901 ONLY FOR X702 HELMET: Position the battery connector and wiring underneath the shell gasket (Fig. 21). Cut along the pre-cut lines of the plastic tab on the back of the comfort padding (Fig. 22). Secure the wiring underneath the plastic tab. Close the cut parts using the cable fixing adhesives (Fig. 23). Fig. 21 Fig. 22 3.6. Fig. 23 Positioning the e-box Connect the microphone to the e-box. (Fig. 24) Position the e-box in the left polystyrene cheek pad housing. (Fig.
EN N.B.: BEFORE replacing the left polystyrene cheek pad, follow the instructions provided in the following chapter. 3.7. Installing the adhesive keyboard Remove the N-Com plug from the left side of the helmet; to make this easier, it is recommended to push the plug from the inside of the helmet. (Fig. 27) Thoroughly clean the outside surface of the shell to make sure that the adhesive keyboard sticks properly.
B901 Remove the protective film from the back of the adhesive keyboard using the special tab. (Fig. 32) Pass the antenna and keypad cable completely through, inside the helmet. Fig. 32 Fig. 33 Apply the keyboard to the shell and press down on its entire surface to make sure that it sticks properly. (Fig. 33) Note: Make sure you do not glue the antenna and keypad cable underneath the keypad support.
EN ONLY FOR FLIP-UP / JET HELMETS: Secure the neck roll (left side), being careful to slide the neck roll plastic ring behind the microphone, then clicking it in the press stud. (Fig. 35) Secure the neck roll (right side) by hooking up the plastic ring to the press-stud. Fig. 35 Warning: Always verify the proper length of your chinstrap and adjust it if necessary, referring to the specific helmet instructions.
B901 5. BASIC FUNCTIONS Press “ON” and keep it pressed for about 2 seconds, until the LEDs turn on and you hear the voice announcement. Press “ON” and keep it pressed for about 6 seconds, until the LEDs turn off and you hear the voice announcement. System ON System OFF 5.1. Volume adjustment You can easily adjust the volume by tapping the “” button or the “” button. You will hear a beep when the volume reaches the maximum or minimum level. The volume is independent for each sound source.
EN 6. CONFIGURATION MENU All Bluetooth pair ups and other adjustments are carried out in this mode. To put the system in “Configuration mode” (starting from a switched off system) press the “ON” key and keep it pressed for 4 seconds, until the blue LED starts flashing quickly and you hear the voice announcement “Configuration ”. Once in the “Configuration” menu, press the keys“” and “” to scroll through the various menu items.
B901 7. PAIRING UP WITH MOBILE PHONES OR OTHER BLUETOOTH DEVICES • • Make sure the B901 is turned off; Put the system in the “Configuration” mode, then press the “ON” key and keep it pressed for 4 seconds until the blue LED starts flashing quickly; Press the key “” to access the “Mobile phone pair up mode””. Turn on the search for Bluetooth devices (smartphone, MP3 reader) on the device; Select the N-Com device.
EN On your own mobile phone (paired up and connected to the N-Com system), call the phone number you wish to assign to the selected speed dialling position. The call is interrupted before it goes through, and the selected number will be saved; at this point you will hear the special voice announcement confirming the selection (“Save Speed Dialling 1” / “Save Speed Dialling 2/ “Save Speed Dialling 3”).
B901 9. MANAGING TWO MOBILE PHONES (OR BLUETOOTH DEVICES) The B901 system can be hooked up to two phones (or Bluetooth) devices at the same time. The second phone (secondary device) can receive calls but not make them.
EN 11. MUSIC VIA CABLE Connect the mini USB connector of the Multimedia Wire (not included) to the helmet and the other end to the audio device. A coloured band on the cable indicates the connector to be hooked up to the audio device. Turning on the cable audio Press the “ON” key three times. Turning off the cable audio Press the “ON” key three times. 12. SATELLITE NAVIGATOR FOR MOTORCYCLES B901 system is compatible with the most common satellite navigators for motorcycles.
B901 14. N-COM INTERCOM (SERIES “900”) The N-Com B901 system allows communication with other N-Com systems, up to a distance of about 700 m (in open field, with no obstacles). Important: The procedure described below refers exclusively to the pairing up and operation between the B901 and the “900” series N-Com systems. To pair up to N-Com systems of a range other than the “900” series, please refer to the procedure described in chapter 14 “Universal Intercom”. N.B.
EN The VOX function is disabled by default on the device. N.B.: In case the pre-setting position is empty, or the system being called cannot be reached within the maximum range or it is already engaged in a phone call, you will hear an error voice message. N.B.: In case the Intercom connection system falls outside the range (Intercom connection interrupted), the B901 system will automatically try to reconnect every 8 seconds. Double beeps will be emitted until the Intercom connection is not restored.
B901 3. In the case where one of the systems presses the “N” key or falls outside the connection range, the group intercom is interrupted. Smart Conference connection Smart Conference disconnection Press the “N” key for 2 seconds. Activation is confirmed by a beep in the helmet and by the voice message “Group Intercom”. Briefly press the “N” key. Disconnection is confirmed by the voice announcement “Group Intercom ended. N.B.
EN • The N-Com B901 systems keeps an active connection with a mobile phone even during Bluetooth communication with other intercom systems. The intercom system connected to N-Com B901 may not allow simultaneous connection to a mobile phone. Only one system paired up in Universal Intercom mode can be stored. • • 15.3.
B901 4. The three systems are not in intercom conference call mode and can talk to each other at the same time. All intercom conference call systems can be disconnected by briefly pressing the “N” command on any one of the devices connected in conference call. 5. In case you wish to add another system (D), the latter must be paired up beforehand to system C. Press the relative connection command to start a 4-participant intercom conference call. N.B.: The “Universal Conference” mode (chapter 14.
EN 17. BATTERY AND RECHARGE 17.1. Low battery signal During its operation, the system alerts the user with a voice message when the battery is low. From the first message, the system has a 1-hour autonomy. Warning is given every 10 minute. 17.2. Charging the system To charge the system, hook it up to the battery charger or to a USB outlet powered with the USB-mini USB cable supplied as standard equipment.
B901 18.
EN Radio Menu N-Com Intercom (900 series) Button N Connection CHANNEL 1 X Disconnection of active intercom X Calling CHANNEL 2 x2 Calling CHANNEL 3 Group intercom connection Group intercom disconnection ON x3 X x2 Turning off the Radio x2 Automatic search for new station Change station (pre-set stations) 2 sec 2 sec Setting*** Pre-set station 4 sec 4 sec 2 sec X x2 x3 Reset *Press any key on the N-Com keypad. **Press the keys at the same time.
B901 19. LIMITED WARRANTY With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: - Read the cautions pertaining to safety and proper use. - Read the warranty terms and conditions. - Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the product has to be taken back to the dealer where it was purchased. 19.
EN 19.3. Validity of this limited warranty This warranty is valid only if the enclosed warranty form is duly and completely filled out with the following information: Product identification code Name and stamp of the authorized dealer. Product purchase date. Buyer’s name and address. Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the product from the dealer. 19.4.
20.
Certification and Safety Approvals FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
aux instructions, il peut occasionner des interférences nuisibles au niveau des communications radios. Cependant, il n’existe aucune garantie que ces interférences ne se produiront pas dans une installation particulière.