7368 ISAM ONT G-2425G-A Product Guide 7368 Intelligent Services Access Manager ONT 7368 ISAM ONT G-2425G-A Product Guide 3FE-48292-ABAA-TCZZA Issue: 01 Nokia — Proprietary and confidential Use pursuant to applicable agreements
7368 ISAM ONT G-2425G-A Product Guide Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. © 2020 Nokia.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 1 Preface This preface provides general information about the documentation set for optical network terminals (ONTs). 1.1 Scope This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the current release. 1.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 1.6 Nokia quality processes Nokia’s ONT quality practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met.
7368 ISAM ONT G-2425G-A Product Guide Procedure 2 ChapterTitleVariable To access individual documents Individual PDFs of customer documents are also accessible through the Nokia Customer Support website. 1.9 1 Navigate to https://customer.nokia.com/support/s and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. 2 From the Technical Content for drop-down menu, choose the product.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 1.9.1 Procedures with options or substeps When there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals. Procedure 3 Example of options in a procedure At step 1, you can choose option a or b. At step 2, you must do what the step indicates. 1 2 Procedure 4 This step offers two options. You must choose one of the following: a This is one option.
368 ISAM ONT G-2425G-A Product Guide 1.10 ChapterTitleVariable Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file. Note — The PDF files in which you search must be in the same folder. Procedure 5 To search multiple PDF files for a common term 1 Open Adobe Acrobat Reader.
ChapterTitleVariable 8 7368 ISAM ONT G-2425G-A Product Guide 3FE-48292-ABAA-TCZZA Issue: 01
7368 ISAM ONT G-2425G-A Product Guide Table of contents 1 Preface.............................................................................................3 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.9.1 1.10 Scope ..........................................................................................................3 Audience......................................................................................................3 Required knowledge.........................................................
7368 ISAM ONT G-2425G-A Product Guide 10 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 ONT environmental requirements .............................................................29 Storage ......................................................................................................29 Transportation ...........................................................................................30 Stationary use............................................................................................
7368 ISAM ONT G-2425G-A Product Guide Issue: 01 5.5 5.6 5.7 5.8 5.9 5.10 5.10.1 5.10.2 5.10.3 5.11 5.11.1 5.11.1.1 5.11.1.2 5.11.1.3 5.11.2 G-2425G-A LEDs ......................................................................................57 G-2425G-A detailed specifications ............................................................59 G-2425G-A GEM ports and T-CONTs.......................................................60 G-2425G-A performance monitoring statistics ...................................
7368 ISAM ONT G-2425G-A Product Guide 12 3FE-48292-ABAA-TCZZA Issue: 01
7368 ISAM ONT G-2425G-A Product Guide List of figures 1 Issue: 01 Preface.............................................................................................3 2 ETSI ONT safety guidelines .........................................................17 Figure 1 Figure 2 Figure 3 Figure 4 PSE certification ........................................................................................19 Laser product label ...................................................................................
7368 ISAM ONT G-2425G-A Product Guide 14 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Wireless Schedule window......................................................................104 IP Routing network window ..................................
7368 ISAM ONT G-2425G-A Product Guide List of tables 1 2 ETSI ONT safety guidelines .........................................................17 Table 1 Safety labels ..............................................................................................18 3 ETSI environmental and CRoHS guidelines...............................27 4 ANSI ONT safety guidelines ........................................................33 Table 2 Safety labels ......................................................
7368 ISAM ONT G-2425G-A Product Guide 16 Table 32 Table 33 Table 34 Table 35 Table 36 Table 37 Table 38 Table 39 Table 40 Table 41 Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Table 50 TR-069 network parameters....................................................................108 QoS Config parameters...........................................................................111 Firewall parameters ................................................................................
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 2 ETSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). 2.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 2.1.1 Safety instruction boxes The safety instruction boxes are provided in the ONT customer documentation.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note — Information of special interest.
7368 ISAM ONT G-2425G-A Product Guide Figure 1 ChapterTitleVariable PSE certification 2.2 Safety standards compliance This section describes the ONT compliance with the European safety standards. 2.2.1 EMC, EMI, and ESD compliance The ONT equipment complies with the following EMC, EMI, and ESD requirements: • EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands • EN 300-386 V1.5.1: Electromagnetic Compatibility and Radio Spectrum Matters • • • • • 2.2.
ChapterTitleVariable 2.2.4 7368 ISAM ONT G-2425G-A Product Guide Laser product standard compliance For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products. If there is an exception to this compliance regulation, you can find this information in the standards compliance section of the unit data sheet in this Product Guide. 2.2.5 Resistibility requirements compliance The ONT equipment complies with the requirements of ITU Recommendation K.
7368 ISAM ONT G-2425G-A Product Guide 2.3.2 ChapterTitleVariable Cabling The following are the guidelines regarding cables used for the ONT equipment: • All cables must be approved by the relevant national electrical code. • The cables for outdoor installation of ONTs must be suitable for outdoor use. • POTS wiring run outside the subscriber premises must comply with the requirements of local electrical codes. In some markets, the maximum allowed length of the outside run is 140 feet (43 m).
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Observe the following danger for laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules. Danger — Possibility of equipment damage. Risk of eye damage by laser radiation. 2.5.1 Laser classification The ONT is classified as a Class 1 laser product based on its transmit optical output. 2.5.1.
7368 ISAM ONT G-2425G-A Product Guide Figure 3 ChapterTitleVariable Laser classification label CLASS 1 LASER PRODUCT ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 4 shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Figure 4 Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
7368 ISAM ONT G-2425G-A Product Guide 2.5.4 ChapterTitleVariable Location class Use cable supports and guides to protect the receptacles from strain. 2.6 Environmental requirements See the ONT technical specification documentation for more information about temperature ranges. During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue.
ChapterTitleVariable 26 7368 ISAM ONT G-2425G-A Product Guide 3FE-48292-ABAA-TCZZA Issue: 01
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 3 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest. 3.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Figure 5 Products below MCV value label 18986 3.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label Figure 6 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products).
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 3.3.3 Transportation According to EN 300-019-1-2 - Class 2.3, transportation of the OLT equipment must be in packed, public transportation with no rain on packing allowed. 3.3.4 Stationary use According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment must be in a temperature-controlled location, with no rain allowed, and with no condensation allowed. 3.3.
7368 ISAM ONT G-2425G-A Product Guide 3.3.7 ChapterTitleVariable End-of-life collection and treatment Electronic products bearing or referencing the symbol shown in Figure 7, when put on the market within the European Union (EU), shall be collected and treated at the end of their useful life, in compliance with applicable EU and local legislation. They shall not be disposed of as part of unsorted municipal waste.
ChapterTitleVariable 32 7368 ISAM ONT G-2425G-A Product Guide 3FE-48292-ABAA-TCZZA Issue: 01
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 4 ANSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals or units (ONTs or ONUs) in the North American or ANSI market. 4.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 4.1.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note — Information of special interest.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Description Label text Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canadian standard compliance (modular ONT) This Class A digital apparatus complies with Canadian ICES-003.
ChapterTitleVariable 4.2.
7368 ISAM ONT G-2425G-A Product Guide 4.2.
ChapterTitleVariable 4.2.5 7368 ISAM ONT G-2425G-A Product Guide Resistibility requirements compliance The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to overvoltage and overcurrents. 4.3 Laser safety guidelines Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Laser product label Figure 10 18455 Figure 11 shows a laser classification label. Laser classification labels may be provided in other languages. Laser classification label Figure 11 CLASS 1 LASER PRODUCT ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 12 shows a laser warning label and an explanatory label for laser products. Explanatory labels may be provided in other languages.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Figure 12 Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
7368 ISAM ONT G-2425G-A Product Guide Figure 13 ChapterTitleVariable Sample laser product safety label on the ONT equipment Model: MFG: MONTH: XX YEAR: XXXX ICS: XX MRev: XX 3FE55851ABAA MAC:XXXXXXXXXXXX SN:ALCLXXXXXXXX I.T.E FCC ID: XXXXXXXXXXX 12VDC 3A ASSEMBLED IN CHINA 2301 Sugar Bush Rd. Raleigh, NC 27612 CLASS 1 LASER PRODUCT PRODUIT LASER DE CLASSE 1 Intertek 4006119 This device complies with Part 15 of the FCC Rule.
ChapterTitleVariable 4.4 7368 ISAM ONT G-2425G-A Product Guide Electrical safety guidelines This section provides the electrical safety guidelines for the ONT equipment. Note — The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. 4.4.1 Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD. Nokia recommends that you prepare the site before you install the ONT equipment. In addition, you must control relative humidity, use static dissipating material for furniture or flooring, and restrict the use of air conditioning. 4.
ChapterTitleVariable 44 7368 ISAM ONT G-2425G-A Product Guide 3FE-48292-ABAA-TCZZA Issue: 01
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 5 G-2425G-A unit data sheet 5.1 G-2425G-A part numbers and identification 5.2 G-2425G-A general description 5.3 G-2425G-A software and installation feature support 5.4 G-2425G-A interfaces and interface capacity 5.5 G-2425G-A LEDs 5.6 G-2425G-A detailed specifications 5.7 G-2425G-A GEM ports and T-CONTs 5.8 G-2425G-A performance monitoring statistics 5.9 G-2425G-A functional blocks 5.10 G-2425G-A standards compliance 5.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Ordering kit part number Provisioning number Description CLEI Code CPR ECI/ Bar code 3FE 48292 BA 3FA 48299 BA G-2426G-A, GPON Dual Band 2+2 RGW ONT with EN7528, MTK7592, and MTC7613b processors. Supports 2 POTS ports, 4xGE, 2x2 802.11b/g/n 2.4G and 802.11ac 5G WLAN. — — — — — — — — — — — — Includes two USB 2.0 Type A ports and a 12V 2A wall-mounted AC/DC power adapter with 2-pin EU input plug and a 1.5 m DC cable.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable ONT part numbers Power model (Model No.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Figure 14 G-2425G-A ONT POWER LINK AUTH LAN1 LAN2 LAN3 LAN4 WP5 WLAN 2.4G WLAN 5G TEL1 TEL2 VOIP USB INTERNET 35646 G-2425G-A indoor ONTs provide the following functions: • Dual-band concurrent 2x2 IEEE 802.11b/g/n 2.4 GHz and 802.11ac MIMO 5 GHz • Supports 802.11 b/g/n 2x2 Wireless 2.4 GHz MIMO; Channel bandwidth 20, 40 MHz, auto • Supports 802.
7368 ISAM ONT G-2425G-A Product Guide • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Issue: 01 ChapterTitleVariable Triple-Play services, including voice, video and high speed Internet access Support for fax services Built-in layer 2 switch; Line Rate L2 traffic IP video distribution Wavelength: 1490 nm downstream; 1310 nm upstream PHY rate: 300 Mbps for 2.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide • Multi-level firewall and ACL • Econet ONT in mainstream 5.2.1 TR-069 parameter support The G-2425G-A ONT supports the following TR-069 features: • • • • • • 5.2.1.1 Host object Port forwarding Optical parameters Object support for optical parameters Statistics and troubleshooting Diagnostic parameter Host object support The ONT provides host object support for: InternetGatewayDeviceLANDevice.Hosts.Host. 5.2.1.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable • temperature • received signal levels • lower thresholds These are the same optical parameters supported in the GUI. For more information, see Table 22 in the chapter “Configure a G-2425G-A indoor ONT”. 5.2.1.
ChapterTitleVariable 5.2.2 7368 ISAM ONT G-2425G-A Product Guide Independent TR69 session with Saas The prime communication between the Nokia Motive cloud solution and the G-2425G-A ONT is TR-069. To keep the Nokia solution independent from the carrier’s ACS, the ONT can establish an independent TR-069 session with the Saas. The Saas WiFi Care URL and credentials can be programmed from the carrier’s ACS solution, or they can be incorporated in a pre-configuration file.
7368 ISAM ONT G-2425G-A Product Guide 5.2.3 ChapterTitleVariable TR69 authentication using TLS and CA certificates G-2425G-A ONTs support TLS, as well as ACS authentication using SHA-256 pre-installed certificates. If the URL is set to the https://... format, by default, the connection will use TLS without authentication mode. The ONT can also authenticate the ACS using a pre-installed CA certificate. 5.2.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 5.2.7 TR-111 support The G-2425G-A ONT supports TR-111, which extends the WAN Management Protocol defined in TR-069 to enhance the ability to remotely manage LAN devices. The device-gateway association enables an ACS to identify the associated gateway through which a device is connected. A connect request via the NAT gateway enables an ACS to initiate a TR-069 session with a device that is operating behind a NAT gateway. 5.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Note (1) The G-2425G-A ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch. 5.4.1 G-2425G-A connections and components Figure 15 shows the physical connections for G-2425G-A indoor ONTs. One USB port is on the side of the ONT.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Figure 16 G-2425G-A indoor ONT with fiber optic connector USB1 USB2 TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 POWER WLAN WPS RESET ON/OFF LED 35648 Table 6 describes the physical connections for G-2425G-A indoor ONTs. Table 6 G-2425G-A indoor ONT physical connections Connection (1) Print Letters Description POTS port TEL1 and TEL2 This connection is provided through an RJ-11 port. One POTS connection is supported.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Connection (1) Print Letters Description On/Off button USB1 and USB2 This button turns the ONT on or off. USB port This connection is provided through 1 USB port on the side of the ONT. The ONT supports external USB hard drives that can be made accessible to all LAN devices. Fiber optic port TEL1 and TEL2 The SC/APC fiber optic port is located at the back of the ONT and provides the connection for the fiber optic cable.
ChapterTitleVariable Table 7 7368 ISAM ONT G-2425G-A Product Guide G-2425G-A indoor ONT LED descriptions Indicator LED color and behavior LED behavior description Power Green solid Power on Red solid Light failed on startup (for example corrupt flash), or self test failed on startup, or self test failed during regular operation or when executed over OMCI Off Power off Link Auth Green solid GPON link between ONT and OLT is operating normally Off GPON link is down or no link is connected Off
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Indicator LED color and behavior LED behavior description INTERNET Green solid HSI WAN is connected: a) the device has an IP address assigned from IPCP, DHCP, or static, and no traffic has been detected; b) the session is dropped due to idle timeout but the PON link is still present. Green flashing PPPoE or DHCP connection is in progress, or transmit and receive traffic is ongoing.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Table 10 G-2425G-A indoor ONT environmental specifications Mounting method Temperature range and humidity Altitude On desk or shelf Operating: 23°F to 113°F (-5°C to 45°C) ambient temperature Contact your Nokia technical support representative for more information 5% to 95% relative humidity, non-condensing Storage: -4°F to 158°F (-20°C to 70°C) 5.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable • Table 14 provides statistics for PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, and PONONTTCVOIP type counters • Table 15 provides statistics for PONONTTC aggregate type counters Note — If you have trouble accessing G-2425G-A ONTs performance monitoring statistics using TL1, please contact your Nokia support representative for more information about how to access and retrieve performance monitoring type counters.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide RXFRAGS LOSTFRAGS ? ? ? ? ? BADGEMHDRS RXBLOCKS G-2425G-A (1) PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP statistics TXFRAGS ONT Package S ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics TXBLOCKS Table 14 Note (1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds
7368 ISAM ONT G-2425G-A Product Guide Figure 18 ChapterTitleVariable G-2425G-A ONT functional block xPON WAN LAN FXS USB DC12V/1.5A UX3320 BOSA GE TXMR (4Port) PEF32002 SLIC USB POWER CIRCUIT Sheet 4 Sheet 5 Sheet 11 Sheet 7 Sheet 8 1.5V CDR 1000BaseX ZSI Interface 3.3V Voice USB BUS EN7528DU MT7592 WiFi Sheet 9 25MHz SoC MEMORY-BUS PCI-E0_BUS DDR3/NAND SPI FLASH Sheet 6 Sheet 1-2 PCI-E1_BUS 5G WiFi MT7613E WiFi GPIO LEDs Sheet 7 35650 5.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide • IEEE 802.11 ac/b/g/n for Wi-Fi • ITU-T G.711, G.722, G.723, G.726, G.729 • SIP RFC 3261 5.10.1 Energy-related products standby and off modes compliance Hereby, Nokia declares that the G-2425G-A ONTs are in compliance with the essential requirements and other relevant provisions of Directive 2009/125/EC together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013.
7368 ISAM ONT G-2425G-A Product Guide 5.10.3 ChapterTitleVariable FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 5.11.1.2 Wi-Fi standards and certifications The Wi-Fi service on G-2425G-A indoor ONTs supports the following IEEE standards and Wi-Fi Alliance certifications: • certified for IEEE 802.11ac/b/g/n/standards • WPA support including WPA-PSK • certified for WPA2-Personal 5.11.1.3 Wi-Fi GUI features G-2425G-A indoor ONTs have HTML-based Wi-Fi configuration GUIs. 5.11.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 6 Install a G-2425G-A indoor ONT 6.1 Purpose 6.2 General 6.3 Prerequisites 6.4 Recommended tools 6.5 Safety information 6.6 Procedure 6.1 Purpose This chapter provides the steps to install a G-2425G-A indoor ONT. 6.2 General The steps listed in this chapter describe mounting and cabling for a G-2425G-A indoor ONT. 6.3 Prerequisites You need the following items before beginning the installation: • all required cables 6.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide • drill and drill bits • paper clip 6.5 Safety information Read the following safety information before installing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
7368 ISAM ONT G-2425G-A Product Guide 6.6 ChapterTitleVariable Procedure Use this procedure to install a G-2425G-A indoor ONT. 1 Place the indoor ONT unit on a flat surface, such as a desk or shelf. Note — The G-2425G-A cannot be stacked with another ONT or with other equipment.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 5 Connect the fiber optic cable with SC/APC adapter to the SC/APC connector on the bottom of the ONT. Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Warning — Be careful to maintain a bend radius of no less than 1.5 in. (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 7 Replace a G-2425G-A indoor ONT 7.1 Purpose 7.2 General 7.3 Prerequisites 7.4 Recommended tools 7.5 Safety information 7.6 Procedure 7.1 Purpose This chapter provides the steps to replace a G-2425G-A indoor ONT. 7.2 General The steps listed in this chapter describe mounting and cabling for a G-2425G-A indoor ONT. 7.3 Prerequisites You need the following items before beginning the installation: • all required cables 7.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide • optical power meter • drill and drill bits 7.5 Safety information Read the following safety information before replacing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
68 ISAM ONT G-2425G-A Product Guide 7.6 ChapterTitleVariable Procedure Use this procedure to replace a G-2425G-A indoor ONT. 1 Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). i Use the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output.
ChapterTitleVariable Figure 20 7368 ISAM ONT G-2425G-A Product Guide G-2425G-A indoor ONT connections Fiber optic port USB USB port Wall mounting hole Wall mounting hole TEL LAN1 LAN2 LAN3 LAN4 POWER RESET WLAN WPS LED ON/OFF On/off button POTS port (RJ-11) Ethernet ports (4) (RJ-45) Power Reset button Wireless Wi-Fi on/off security button buttons 28478 3 Power down the unit by using the on/off power switch.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 8 Connect the POTS cable directly to the RJ-11 port as per local practices; see Figure 20 for the location of the RJ-11 ports. 9 If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection. See the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information about fiber optic handling, inspection, and cleaning.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 14 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information. Note — A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 8 Configure a G-2425G-A indoor ONT 8.1 General 8.2 HGU mode GUI configuration 8.1 General Please refer to the configuration information provided with your OLT for the software configuration procedure for a G-2425G-A ONT. For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 8.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 2 Enter your username and password in the Log in window, as shown in Figure 21. The default user name is AdminGPON. The default password is ALC#FGU Figure 21 Web login window Caution — Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID.
7368 ISAM ONT G-2425G-A Product Guide • • • • • Procedure 7 ChapterTitleVariable WAN status WAN status IPv6 Home networking information optics module status voice information Device information retrieval 1 Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 22. Device Information window Figure 22 Note — Upon login, the GPON Home Gateway window displays the WAN status block on the bottom left part of each window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description Vendor Name of the vendor Serial Number Serial number of the ONT Hardware version Hardware version of the ONT Boot version Boot version of the ONT Software version Software version of the ONT Chipset Chipset of the ONT Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds (2 of 2) 80 2 Click Refresh to update the displayed information. 3 STOP.
7368 ISAM ONT G-2425G-A Product Guide Procedure 8 LAN status retrieval 1 Figure 23 ChapterTitleVariable Select Status > LAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 23. LAN status window Table 18 describes the fields in the LAN status window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description Wireless Encryption Status Encryption type used on the wireless connection Wireless Rx Packets Number of packets received on the wireless connection Wireless Tx Packets Number of packets transmitted on the wireless connection Wireless Rx Bytes Number of bytes received on the wireless connection Wireless Tx Bytes Number of bytes transmitted on the wireless connection Power Transmission (mW) Power of the wireless trans
7368 ISAM ONT G-2425G-A Product Guide Procedure 9 WAN status retrieval 1 Figure 24 ChapterTitleVariable Select Status > WAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 24. WAN status window Table 19 describes the fields in the WAN status window. Table 19 WAN status parameters Field Description WAN Connection List Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description WAN Link Status Whether the WAN link is up or down IPv4 Address IP Address of the ONT Netmask Network mask Gateway Gateway address Primary DNS Primary Domain Name Server Second DNS Secondary Domain Name Server Manual DNS Manual Domain Name Server PON Link Status Whether the PON link is up or down Tx Packets Number of packets transmitted on the WAN connection Rx Packets Number of packets received on the WAN co
7368 ISAM ONT G-2425G-A Product Guide Procedure 10 WAN status IPv6 retrieval 1 Figure 25 ChapterTitleVariable Select Status > WAN Status IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 25. WAN status IPv6 window Table 20 describes the fields in the WAN status IPv6 window. Table 20 WAN status IPv6 parameters Field Description WAN Connection List Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description Primary DNS Primary Domain Name Server Second DNS Secondary Domain Name Server PON Link Status Whether the PON link is up or down Tx Packets Number of packets transmitted on the WAN connection Rx Packets Number of packets received on the WAN connection Tx Dropped Number of packets dropped on the transmit WAN connection Rx Dropped Number of packets dropped on the receive WAN connection Err Packets Number of errore
7368 ISAM ONT G-2425G-A Product Guide Procedure 11 Home networking information retrieval 1 Figure 26 ChapterTitleVariable Select Status > Home Networking from the top-level menu in the GPON Home Gateway window, as shown in Figure 26. Home networking information window Table 21 describes the fields in the Home networking window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description Access Point Hexadecimal address of the wireless access point Local Devices Table entry Each entry indicates the status (active or inactive), connection type, device name, IP address, hardware address, IP address allocation, lease remaining, and last active time of each connected local device. (2 of 2) 2 Click Delete to delete a particular local device connection. 3 Click Refresh to update the displayed information.
7368 ISAM ONT G-2425G-A Product Guide Table 22 Issue: 01 ChapterTitleVariable Optics module status parameters Field Description Laser Bias Current (ONT ANI-ONT-Side Optical Measurements) Laser bias current, measured in uA Optics Module Voltage (ONT ANI-ONT-Side Optical Measurements) Optics module voltage, measured in V Optics Module Temperature (ONT ANI-ONT-Side Optical Measurements) Optics module temperature, measured in C Rx Optics Signal Level at 1490 nm (ONT ANI-ONT-Side Optical Measurement
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 13 Voice information retrieval 1 Figure 28 Select Status > Voice Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 28. Voice Information window Table 23 describes the fields in the Voice Information window. Table 23 Voice Information parameters Field Description Line Choose a line from the drop-down menu. The default is Line 1.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Field Description Register Status The default is Registered Blank if no voice service is provisioned Register Error Code SIP standard error code for the register status; for example, 401, 403, 503 This field is blank if the register is set to OK Register Error Reason SIP standard error reason for the register status This field is blank if the register is set to OK User Agent IP IP address of the user agent ExternalIPAddress in WANIPConnec
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 14 LAN networking configuration 1 Figure 29 Select Network > LAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 29. LAN network window Table 24 describes the fields in the LAN network window.
7368 ISAM ONT G-2425G-A Product Guide Table 24 ChapterTitleVariable LAN network parameters Field Description Port Mode All Ports to Bridge Mode Select this checkbox to set all ports to Bridge mode Port 1 - 4 Drop-down port mode for each port: Route mode or Bridge mode IPv4 Address IP Address of the ONT Subnet Mask Subnet mask of the ONT DHCP enable Select this checkbox to enable DHCP DHCP Start IP Address Starting DHCP IP address DHCP End IP Address Ending DHCP IP address DHCP Lease Time
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 15 LAN IPv6 networking configuration 1 Figure 30 Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 30. LAN IPv6 network window Table 25 describes the fields in the LAN IPv6 network window.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Field Description Interface This field appears if you selected the Wan Connection option for the “prefix config” field. Choose a WAN connection interface from the drop-down menu.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 16 WAN networking configuration 1 Figure 31 Select Network > WAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 31. WAN network window Table 26 describes the fields in the WAN network window.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Field Description WAN IP Mode Choose an IP mode from the drop-down menu Manual DNS Manual Domain Name Server (2 of 2) 2 Configure a specific WAN connection. 3 Click Save. 4 STOP. This procedure is complete. Procedure 17 WAN DHCP configuration 1 Figure 32 Select Network > WAN DHCP from the top-level menu in the GPON Home Gateway window, as shown in Figure 32. WAN DHCP window Table 27 describes the fields in the WAN DHCP window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Table 27 98 WAN DHCP parameters Field Description WAN Connection List Choose a WAN connection from the drop-down menu DHCP Option 50 Persistent Select this checkbox to enable DHCP Option 50 persistent Enable DHCP Option 60 Select this checkbox to enable DHCP Option 60 (vendor class identifier) Enable DHCP Option 61 Select this checkbox to enable DHCP Option 61 (client identifier) Enable DHCP Option 77 Select this checkbox to enable D
7368 ISAM ONT G-2425G-A Product Guide Procedure 18 WiFi 2.4GHz networking configuration 1 Figure 33 ChapterTitleVariable Select Network > WiFi 2.4GHz from the top-level menu in the GPON Home Gateway window, as shown in Figure 33. WiFi 2.4GHz network window Table 28 describes the fields in the WiFi 2.4GHz network window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Table 28 WiFi 2.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Field Description WPA Key Enter the WPA key Enable WPS Choose Enable or Disable WPS from this drop-down menu WPS Mode Choose a WPS mode from the drop-down menu: PBC (Push Button Connect) or PIN (Personal Identification Number) (2 of 2) Issue: 01 2 Configure the WiFi connection. 3 If you have enabled and configured WPS, click WPS connect. 4 Click Save. 5 STOP. This procedure is complete.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 19 WiFi 5GHz networking configuration 1 Figure 34 Select Network > WiFi 5GHz from the top-level menu in the GPON Home Gateway window, as shown in Figure 34. WiFi 5GHz network window Table 29 describes the fields in the WiFi 5GHz network window.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Field Description Channel Choose a channel from the drop-down menu or choose Auto to have the channel automatically assigned Transmitting Power Choose a percentage for the transmitting power from the drop-down menu: • • • • Low (20%) Medium (40%) High (60%) Maximum (100%) WMM Choose Enable or Disable from the drop-down menu to enable or disable WiFi multi-media Total MAX Users Enter the total number of MAX users SSID Configuration SSID
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 20 Wireless scheduling 1 Figure 35 Select Network > Wireless Schedule from the top-level menu in the GPON Gateway window, as shown in Figure 35. Wireless Schedule window 2 Select the Schedule Function checkbox to turn the wireless signal off for the configured period. 3 Click the plus sign (+) to add a scheduling rule. A separate panel displays for configuring wireless schedule rules.
7368 ISAM ONT G-2425G-A Product Guide 8 Click Save Changes. 9 STOP. This procedure is complete. Procedure 21 IP Routing configuration 1 Figure 36 ChapterTitleVariable Select Network > IP Routing from the top-level menu in the GPON Home Gateway window, as shown in Figure 36. IP Routing network window Table 30 describes the fields in the IP Routing network window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description Destination IP Address Enter the destination IP address Destination Netmask Enter the destination network mask Gateway Enter the gateway address IPv4 Interface Choose a WAN connection previously created in the WAN network window from the drop-down menu Forwarding Policy Choose a forwarding policy from the drop-down menu (2 of 2) 106 2 Enter the IP routing information. 3 Click Add. 4 STOP.
7368 ISAM ONT G-2425G-A Product Guide Procedure 22 DNS configuration 1 Figure 37 ChapterTitleVariable Select Network > DNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 37. DNS network window Table 31 describes the fields in the DNS network window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 3 Enter the domain name and IPv4 address and click Add. 4 If required, associate an origin domain with a new domain, click Add. 5 STOP. This procedure is complete. Procedure 23 TR-069 configuration 1 Figure 38 Select Network > TR-069 from the top-level menu in the GPON Home Gateway window, as shown in Figure 38. TR-069 network window Table 32 describes the fields in the TR-069 network window.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Field Description URL URL of the auto-configuration server Username Username used to log in to the auto-configuration server Password Password used to log in to the auto-configuration server Connect Request Username Username used to log in to the ONT Connect Request Password Password used to log in to the ONT (2 of 2) 2 Configure TR-069 by entering the required information. 3 Click Save. 4 STOP. This procedure is complete.
ChapterTitleVariable Figure 39 7368 ISAM ONT G-2425G-A Product Guide QoS Config window (L2) Figure 40 shows the window for configuring QoS L3 (Layer 3 packet sizes).
7368 ISAM ONT G-2425G-A Product Guide Figure 40 ChapterTitleVariable QoS Config window (L3) Table 33 describes the fields in the QoS Config window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description Type Choose a QoS service layer type from the drop-down menu L2 or L3. Classification Criteria Source MAC Enter the source MAC Select the Exclude checkbox to exclude the source MAC Interface Choose an interface from the drop-down menu Classification Result DSCP Remark Enter the value for the DSCP mark (range: 0-63); valid only for L3 Criteria 802.1p Remark Enter the value for the 802.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable • parental control • DMZ and ALG • access control Procedure 25 Firewall configuration 1 Select Security > Firewall from the top-level menu in the GPON Home Gateway window, as shown in Figure 41. Figure 41 Firewall window Three security levels are available: High, Low, and Off.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 3 Click Save. 4 STOP. This procedure is complete. Procedure 26 MAC filter configuration 1 Select Security > Mac Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 42. Figure 42 MAC filter window Table 35 describes the fields in the MAC filter window.
7368 ISAM ONT G-2425G-A Product Guide Table 35 ChapterTitleVariable MAC filter parameters Field Description Ethernet Interface MAC Filter Mode Choose the MAC filter mode from the drop-down menu: Blocked or Allowed LAN Port LAN port range MAC Address Choose the MAC address from the drop-down menu or enter the address in the text field Wi-Fi SSID Issue: 01 MAC Filter Mode Choose the MAC filter mode from the drop-down menu: Blocked or Allowed SSID Select Choose the SSID from the drop-down menu
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 27 IP filter configuration 1 Select Security > IP filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 43. Figure 43 IP filter window Table 36 describes the fields in the IP filter window.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 3 Click Add. 4 STOP. This procedure is complete. Procedure 28 URL filter configuration 1 Select Security > URL Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 44. URL Filter window Figure 44 Note — You cannot use URL filtering for HTTPS. The URL is encrypted when using HTTPS. Table 37 describes the fields in the URL Filter window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description URL Address Type the URL address Port - default to 80 Type the port number; the default is 80 (2 of 2) 118 2 Configure the URL Filter. 3 Click Add Filter. 4 STOP. This procedure is complete.
7368 ISAM ONT G-2425G-A Product Guide Procedure 29 Parental control 1 Issue: 01 ChapterTitleVariable Select Security > Parent Control from the top-level menu in the GPON Gateway window, as shown in Figure 45.
ChapterTitleVariable Figure 45 7368 ISAM ONT G-2425G-A Product Guide Parental Control window Table 38 describes the fields in the Parental Control window.
7368 ISAM ONT G-2425G-A Product Guide Table 38 ChapterTitleVariable Parental control parameters Field Description Access Control Select this checkbox to enable access control Add Access Control rule Policy Name Enter a name for the parental control policy or choose a policy from the list MAC Address Enter the MAC address or choose a MAC address from the list IPv4 Address Enter the IPv4 address for the device or choose an IPv4 address from the list Url Port Enter the URL port for the device D
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 30 DMZ and ALG configuration 1 Select Security > DMZ and ALG from the top-level menu in the GPON Home Gateway window, as shown in Figure 46. Figure 46 DMZ and ALG window Table 39 describes the fields in the DMZ and ALG window.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 5 Click Save DMZ. 6 STOP. This procedure is complete. Procedure 31 Access control configuration This procedure describes how to configure the access control level (ACL). Note 1 — ACL takes precedence over the firewall policy. Note 2 — The trusted network object will be shared for all WAN connections; it is not applied individually to a WAN connection.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Table 40 Access control parameters Field Description WAN Choose a connection from the drop-down menu Trusted Network Enable Click to enable or disable ICMP, Telnet, SSH, HTTP, TR-069, HTTPS, SFTP Select an access control level for each protocol: WAN side: Allow, Deny, or Trusted Network Only LAN side: Allow or Deny Trusted Network Source IP Start Enter a start IP address for the new subnet trusted network Source IP End Enter an end IP
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable • USB • UPnP and DLNA Procedure 32 Port forwarding configuration 1 Figure 48 Select Application > Port forwarding from the top-level menu in the GPON Home Gateway window, as shown in Figure 48. Port forwarding window Table 41 describes the fields in the port forwarding window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Field Description WAN Connection List Choose a WAN connection from the drop-down menu Note: only active devices are shown on this menu (2 of 2) 2 Configure port forwarding. 3 Click Add. 4 STOP. This procedure is complete. Procedure 33 Port triggering 1 Figure 49 Select Application > Port Triggering from the top-level menu in the GPON Gateway window, as shown in Figure 49.
7368 ISAM ONT G-2425G-A Product Guide Table 42 ChapterTitleVariable Port triggering parameters Field Description Application Name Choose an application name from the drop-down menu The default is Custom settings Open Port Enter the open port range Triggering Port Enter the triggering port range Expire Time Enter the expiration time in seconds Open Protocol Choose the open port protocol from the drop-down menu: Trigger Protocol • • • TCP UDP TCP/UDP Choose the triggering port protocol from
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 34 DDNS configuration 1 Figure 50 Select Application > DDNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 50. DDNS window Table 43 describes the fields in the DDNS window.
7368 ISAM ONT G-2425G-A Product Guide Procedure 35 NTP configuration 1 Figure 51 ChapterTitleVariable Select Application > NTP from the top-level menu in the GPON Home Gateway window, as shown in Figure 51. NTP window Table 44 describes the fields in the NTP window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 3 Click Save. 4 STOP. This procedure is complete. Procedure 36 USB configuration You can connect USB storage devices and USB printers to the USB ports of the device. The USB menu enables you to configure FTP and SFTP for your USB storage devices. The USB connected devices are shown in overview table on the bottom of the USB window. 1 Figure 52 Select Application > USB from the top-level menu, as shown in Figure 52.
7368 ISAM ONT G-2425G-A Product Guide Table 45 ChapterTitleVariable USB parameters Field Description Enable FTP server Select this checkbox to enable using an FTP server Username Username for the FTP server Password Password for the FTP server Re-enter Password Password for the FTP server Enable SFTP server Select this checkbox to enable using an SFTP server Enable SFTP for Remote Access Select this checkbox to enable SFTP for remote access Username Username for the SFTP server Password
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 37 UPnP and DLNA configuration 1 Figure 53 Select Application > UPnP and DLNA from the top-level menu in the GPON Home Gateway window, as shown in Figure 53. UPnP and DLNA window 2 Select the Enable UPnP/DLNA checkbox to enable UPnP/DLNA. 3 Click Save/Apply. 4 STOP. This procedure is complete. 8.2.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable • diagnose WAN connections • view log Procedure 38 Password configuration A password must adhere to the password rules, which are as follows: • • • • • the password may consist of uppercase letters, lowercase letters, digital numbers, and the following special characters ! # + , - / @ _ : = ] the password length must be from 8 to 24 characters the first character must be a digital number or a letter the password must contain at least two types
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide • • 1 Figure 54 the first character cannot be a special character there are not enough character classes Select Maintain > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 54. Password window Table 46 describes the fields in the password window.
7368 ISAM ONT G-2425G-A Product Guide 3 Click Save. 4 STOP. This procedure is complete. Procedure 39 WAN speed test 1 Figure 55 ChapterTitleVariable Select Maintain > Speed Test from the top-level menu in the GPON Home Gateway window, as shown in Figure 55. Speed Test window 2 Click Start to start the speed test. Enter the URL for the test server in the pop-up window. 3 Issue: 01 STOP. This procedure is complete.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 40 LOID configuration 1 Figure 56 Select Maintain > LOID Config from the top-level menu in the GPON Home Gateway window, as shown in Figure 56. LOID Config window Table 47 describes the fields in the LOID configuration window.
7368 ISAM ONT G-2425G-A Product Guide Procedure 41 SLID configuration 1 Figure 57 ChapterTitleVariable Select Maintain > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 57. SLID configuration window Table 48 describes the fields in the SLID configuration window.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 3 Click Save. 4 STOP. This procedure is complete. Procedure 42 Device management 1 Figure 58 Select Maintain > Device Management from the top-level menu in the GPON Home Gateway window, as shown in Figure 58. Device management window Table 49 describes the fields in the Device management window.
7368 ISAM ONT G-2425G-A Product Guide 3 Click Add. 4 STOP. This procedure is complete. Procedure 43 Backup and restore 1 Figure 59 Issue: 01 ChapterTitleVariable Select Maintain > Backup and Restore from the top-level menu in the GPON Home Gateway window, as shown in Figure 59. Backup and Restore window 2 Click Choose file and choose the backup file. 3 Click Import to restore the ONT to the saved backup, or click Export to export the current ONT configuration to the backup file. 4 STOP.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 44 Upgrade firmware 1 Figure 60 140 Select Maintain > Firmware Upgrade from the top-level menu in the GPON Home Gateway window, as shown in Figure 60. Firmware upgrade window 2 Click Choose file and choose the firmware file. 3 Click Upgrade to upgrade the firmware. 4 STOP. This procedure is complete.
7368 ISAM ONT G-2425G-A Product Guide Procedure 45 Reboot ONT 1 Figure 61 Issue: 01 ChapterTitleVariable Select Maintain > Reboot Device from the top-level menu in the GPON Home Gateway window, as shown in Figure 61. Reboot window 2 Click Reboot to reboot the ONT. 3 STOP. This procedure is complete.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 46 Restore factory defaults 1 Figure 62 142 Select Maintain > Factory Default from the top-level menu in the GPON Home Gateway window, as shown in Figure 62. Factory default window 2 Click Factory Default to reset the ONT to its factory default settings. 3 STOP. This procedure is complete.
7368 ISAM ONT G-2425G-A Product Guide Procedure 47 Diagnose WAN connections 1 Figure 63 Issue: 01 ChapterTitleVariable Select Maintain > Diagnostics from the top-level menu in the GPON Home Gateway window, as shown in Figure 63. Diagnostics window 2 Choose a WAN connection to diagnose from the drop-down menu. 3 Enter the IP address or domain name. 4 Select the test type: ping, traceroute, or both. 5 Enter the number of ping attempts to perform (1 - 1000); the default is 4.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide 9 Click Cancel to cancel the test. 10 STOP. This procedure is complete. Procedure 48 View log files 1 Figure 64 144 Select Maintain > Log from the top-level menu in the GPON Home Gateway window, as shown in Figure 64.
7368 ISAM ONT G-2425G-A Product Guide 2 Choose a write level from the drop-down menu to determine which types of events are recorded in the log file: • • • • • • • • 3 Emergency Alert Critical Error Warning Notice Informational Debug Choose a reading level from the drop-down menu to determine which types of events to display from the log file: • • • • • • • • 8.2.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 49 Retrieve Residential Gateway (RG) troubleshooting counters 1 Select RG Troubleshooting Counters from the left menu in the GPON Home Gateway window. The RG Troubleshooting Counters window appears; see Figure 65. Figure 65 RG Troubleshooting Counters window Table 50 describes the fields in the RG Troubleshooting Counters window.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable Field Description US Packet Loss The number of upstream packages lost DS Packet Loss The number of downstream packages lost Internet Status Whether the broadband connections is active (UP) or not (DOWN) Latency This test is used to determine the lowest round-trip time in milliseconds by pinging the target server multiple times Click Latency Test to specify the time for the test The default is weekly, performed at idle to a public server
ChapterTitleVariable 148 7368 ISAM ONT G-2425G-A Product Guide 3FE-48292-ABAA-TCZZA Issue: 01
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable 9 ONT configuration file over OMCI 9.1 Purpose 9.2 Supported configuration file types 9.3 ONT configuration file over OMCI 9.1 Purpose This procedure describes how to use configuration files over OMCI to configure ONTs.
ChapterTitleVariable Table 51 7368 ISAM ONT G-2425G-A Product Guide Supported configuration files File Index Description Details Supported ONTs/DPU PRE ONT pre-configuration file The XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings. All Nokia GPON and 10 GPON ONT. The pre-configuration file includes the factory default value for the residential gateway.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable File Index Description Details Supported ONTs/DPU GFT G.fast-related configuration file This text-based json script file controls the default behavior of the G.Fast ONT. Nokia G.fast. This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning. While the ONT functions well with the default values; they can optionally be customized.
ChapterTitleVariable 7368 ISAM ONT G-2425G-A Product Guide Procedure 50 Configuring an ONT using a configuration file via OMCI 1 Generate the TAR file to be uploaded to the OLT. Using the raw configuration file(s) provided by Nokia, generate the TAR file as follows: i On a Linux platform, rename the raw configuration file to adhere to the naming convention, as described in section 9.2. ii Tar the ABCXXXXVER raw configuration file: tar -cf ABCXXXXVER.
7368 ISAM ONT G-2425G-A Product Guide ChapterTitleVariable FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required. iv If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same.
ChapterTitleVariable 154 7368 ISAM ONT G-2425G-A Product Guide 3FE-48292-ABAA-TCZZA Issue: 01
Customer document and product support Customer documentation Customer Documentation Welcome Page Technical Support Customer Documentation Technical Support Documentation feedback Customer Documentation Feedback
Copyright 2020 Nokia.